Search Documents

By L. L. Melton, D. L. Lord, B. W. Hulsey

A mathematical model d1.20p/4L = A(8v)8 derived from the Blasius equation is proposed to be applicable to turbulent flow through straight cylindrical pipe for time-independent fluids which produce a diameter family of straight parallel lines on a log (dp/4L) vs log (8v/d) plot or stress-flow diagram. Such a correlation should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable frictional pressure reductions. The Newtonian diameter exponent value 1.20 is shown to be empirically valid for turbulent non-Newtonian flow by application of numerical analysis methods. Multiple regression analysis is applied to a logarithmic linearization of the proposed model. An improved data fit results from further linearization achieved by taking linear terms from a generalized Taylor's series expansion about the multiple regression coefficients. Extensive experimental data obtained in five pipe diameters with water, sodium carboxymethyl-celIulose solutions, guar gum solutions, bentonite clay suspensions and calcium carbonate slurries are presented. Except for calcium carbonate slurries, which were investigated rather than time-dependent cement slurries, the fluids studied contain drilling or fracturing fluid additives. The behavior exhibited by these fluids is considered typical of most fluids encountered in drilling, cementing and fracturing operations. INTRODUCTION Considerable difficulties have been encountered in predicting turbulent flow pressure drops produced by non-Newtonian fluids flowing through straight cylindrical pipe. Correlations previously presented require extensive experimental data which represent several pipe diameters and a wide flow rate range to estimate the necessary scale-up parameters.l-7 One must implement either elaborate experimental apparatus or spend considerable time and effort to gather these data. Presented here is a correlation method which should minimize the experimental effort and data analysis normally required by utilizing flow data taken with only one pipe diameter. Turbulent flow data (up-stream and down-stream pressure and volumetric flow rates) were collected for five pipe diameters through operation of a small pipeline system having an electronic data acquisition and digitizing system. A mathematical model derived from the Blasius equation was utilized to describe the functional relationship between pressure drop and the two independent variables, diameter and average flow velocity. A correlation, which should produce a valid single-pipe scale-up, resulted from a computer-implemented statistical and numerical data analysis for several time-independent non-Newtonian fluids.

By AIME AIME

THE CHAIRMAN of the fast growing Petroleum Division is not only a graduate of the University of California, but a third generation native son. After a few years spent in hard-rock geology, his professional efforts were transferred to the sedimentaries and to petroleum investigations, as a consulting geologist. For ten years these investigations covered the Rocky Mountain, Oklahoma, Texas, and eastern districts. After the war he returned to Casper, Wyo., as chief geologist for the Consolidated Royalty Oil and Western Exploration Companies. This employment afforded him the opportunity to study particularly the economic relationship between the lessor-lessee interests in development and production, a somewhat unusual type of petroleum specialization.

Jan 1, 1939

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By J. A. Bowknocker

NATURAL GAS was secured in the Trenton limestone near Findlay, Hancock County, in 1884, and oil in the following year. Drilling was rapid so that the production increased by leaps and bounds; in 1896, it exceeded 25,250,000 bbl., the maximum for the field. Since that time, the yield has decreased steadily and in 1921 was only 1,447,243 bbl. The territory extends as an arc of a circle from near the western end of Lake Erie southwest into Indiana, which it enters in Adams and Jay Counties. Sixteen counties are listed in Ohio but five of them combined had a new production of only 264 bbl. and they might well be omitted. Progress in the Trenton limestone field of northwest Ohio in 1923 is shown in Table 1.

Jan 3, 1924

By John F. Abel

At the spring meeting of the Open Pit Division of AIME's Arizona Section, I was asked a question which indicates the acceleration of technical advancement. The question was: "How does an engineer at a properly keep abreast of what is new?" The fact that some 200 Arizona AIME members were at the meeting is a testimonial to the desire of these men to do just that- keep abreast. There is a great deal of talk in academic circles about the built-in obsolescence of an engineering or scientific education, too. About 100 commencement speakers every spring are sure to admonish the graduates that education is a continuing thing. Mining engineers are a small fraternity. We keep informed by talking to one another. Talking shop is valuable but there is no substitute for reading.

Jan 1, 1970

By Guilliaem Aertsen

The derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria." In the infancy of railroads, the tracks consisted of flat bars of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which, in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now Wayne Junction, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the fist locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler and Matthias Baldwin were brothers-in-law; the latter's name will be identified with American locomotives until locomotives are forgotten. The wheels on these first locomotives, designed to run on this primitive rail, mere shod with plain iron bands, bent and welded. The flanges consisted of separate iron bands, bent sidewise,welded, and bolted to the sides of the wooden fellies, or rims. Before many years had elapsed the tires were fabricated of iron bands, rolled in one piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices. Germany is generally given the credit for first making such tires of

Jan 1, 1917

By Jesse O. Betterton

Recently some experimental work was conducted by the author in connection with the direct leaching of certain zinc ores with sulfuric acid with the object of subsequently recovering the zinc by electrolysis. The ores contained relatively large quantities of soluble silica, making it necessary to evolve special methods for handling the silicate solutions resulting from a leach of the ore, and also for the final removal of the silica before electrolysis. The problem was complicated by the presence of vanadium in the ore, the commercial recovery of which was very desirable. This paper, however, deals only with the silica phase of the problem. The zinc in the ore occurs in the form of a silicate (hemimorphite) and, to a very small extent, as the phosphate (hopeite) and carbonate (calamine); the vanadium is found as descloizite and vanadinite but mainly as descloizite. The experimental work was done in a plant producing 50 lb. of zinc = daily, in which the complete cycle of operations, including the final electrodeposition of the zinc, was performed continuously for one year. Some of the conclusions given here are the result of the operations in -this plant; the others are from laboratory tests inaugurated both as a guide to the plant operations and, in certain cases especially, to determine the limits in question. The practice in the 50-lb. zinc plant was to direct leach the ore crushed to pass 40 mesh, with spent electrolyte from the cells containing approximately 3 per cent. zinc and 10 per cent. free acid. This resulted in an acid leach solution and an ore residue. The acid leach solution was ' subjected to a special treatment for subsequent removal of vanadium; then the silica and vanadium in solution were precipitated together and removed as a "silica residue" by pressing through an ordinary plate and frame press. The next step was to treat the filtrate from the silica residue with zinc dust as a final purification step before it went to

Jan 1, 1923

By Jesse O. Betterton

Recently some experimental work was conducted by the author in connection with the direct leaching of certain zinc ores with sulfuric acid with the object of subsequently recovering the zinc by electrolysis. The ores contained relatively large quantities of soluble silica, making it necessary to evolve special methods for handling the silicate solutions resulting from a leach of the ore, and also for the final removal of the silica before electrolysis. The problem was complicated by the presence of vanadium in the ore, the commercial recovery of which was very desirable. This paper, however, deals only with the silica phase of the problem. The zinc in the ore occurs in the form of a silicate (hemimorphite) and, to a very small extent, as the phosphate (hopeite) and carbonate (calamine); the vanadium is found as descloizite and vanadinite but mainly as descloizite. The experimental work was done in a plant producing 50 lb. of zinc = daily, in which the complete cycle of operations, including the final electrodeposition of the zinc, was performed continuously for one year. Some of the conclusions given here are the result of the operations in -this plant; the others are from laboratory tests inaugurated both as a guide to the plant operations and, in certain cases especially, to determine the limits in question. The practice in the 50-lb. zinc plant was to direct leach the ore crushed to pass 40 mesh, with spent electrolyte from the cells containing approximately 3 per cent. zinc and 10 per cent. free acid. This resulted in an acid leach solution and an ore residue. The acid leach solution was ' subjected to a special treatment for subsequent removal of vanadium; then the silica and vanadium in solution were precipitated together and removed as a "silica residue" by pressing through an ordinary plate and frame press. The next step was to treat the filtrate from the silica residue with zinc dust as a final purification step before it went to

Jan 1, 1923

By AIME

BILL BREWSTER was a natural for the steel business. His family lived at Iron Mountain, Mich., when Bill was born on June 14, 1889, so that he had iron in his blood. Always he has looked toward the finished product, rather than the raw material, so that it was a fore-gone conclusion that he should work toward the steel end of the business. After preparing for college at Hotch-kiss Academy he entered the Sheffield Scientific School of Yale University from which he graduated in 1910 with the degree of Bachelor of Philosophy. No reunion of his class would be complete without Bill Brewster. Unlike many of us who try several jobs before settling down, Bill shot straight for the mark. After a summer's work at Iron Mountain, making sure of his background in the production of the raw iron ore, he entered the employ of Wisconsin Steel Works of the International Harvester Co. in September 1910 and has been there ever since. It wasn't much of a job to start with, just a laborer in the billet dock department, but soon there was an opening in the blast-furnace department, where he started as superintendent's clerk in December 1910.

Jan 1, 1946

By H. R. Barnhurst

It would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Donbtless the crossing of the sticks of wood in building a mood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets, utilized metal bars as supports for the same purpose. It is probable that Tuba1 Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in cast iron, grate bars came in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deli-. ciencies in its primary development, and within that time there has been great advancement in the means of producing initially a fire of high effciency, so that to-day we are moving rapidly toward both high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This, question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to him nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for making what was at best a very imperfect pulverization of the coal, arid the expense of preparation mas very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 1, 1914

The American Institute of Mining Engineers, the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers have established the . Engineering Societies Employment Bureau under the management of their Secretaries. One of the purposes of the Bureau is to keep in touch with all engineering firms with a view to supplying them with desirable men. Plans are under way to assist in placing men who are retiring from the government service. The Bureau is not intended to be exclusively for the benefit of unemployed members, of the Founder Societies; non-members who are introduced properly will be registered. Information, registration forms, etc., may be obtained from the office of the Bureau, Engineering Societies Building, 29 West 39 Street, New York, Room 903.

Jan 1, 1919

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or. other persons.) Position for a single man experienced in cyanide mill construction and operation at a small mine in Nicaragua. Salary $150 per month and expenses. No.. 39. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, desires position in ore dressing, either experimental or operating. Has had practical experience in flotation and other special methods. No. 228. Member, technical. graduate, 10 years' experience in Belgian coal mines, five years' experience in American coal mines in connection with reorganization of companies and opening of new coal fields. Aged 37. Speaks Spanish. No. 229

Jan 7, 1915

PAUL D. FOOTE AND T. R. HARRISON, Washington, D. C. (written discussion *).-There are several methods for measuring the internal resistance of a battery, the line resistance in a circuit containing an e.m.f., or the true value of this e.m.f. The writers, however, were the first to em-ploy a simple principle whereby the total resistance of the circuit is ad-justed to a preassigned value for which the scale of the millivoltmeter is graduated, the only e.m.f. employed being that of the source measured. One of the simplest forms of these instruments is described on page 2842, September Bulletin. In papers now in the press we have described some twenty modifications of this simple design but all operating upon the same fundamentally new principle. The instrument devised by Mr. . Porter is of this general type but, unlike the designs we have recom-mended, is open to serious objections.

Jan 12, 1919

By J. G. LECKIE

During the first ten months of 1943 copper was produced at a higher rate than in 1947. However, on Oct. 24 one of the large mines was shut down due to a strike. As of Dec. 31 the strike was still in effect and had already resulted in a loss of production of 50,000 tons of copper. The demand for copper was considerably greater throughout the year than the supply. The price of electrolytic copper delivered at the Atlantic Seaboard refineries advanced from 21.20 to 23.20 cents per lb during the year. This sustained demand for copper, together with the increase in price, has had the natural effect of spurring interest in uncovering new deposits, and in re-examination of known low-grade deposits and old tailing clumps. This is in addition to the usual reevaluation activities which normally result from the constant improvements in efficiency of ore concentration.

Jan 1, 1949

By H. V. Winchell

It seems to me that uniformity of mining law in North America must of necessity start with uniformity in each country. I understand that the Provinces of Canada have the right to make their own individual laws and conditions, to prescribe the terms under which the prospector or the applicant for mineral titles may secure the same. That is not true of the states in the United States. In this country, the Federal Mining Law was made applicable to the public domain, which, at the time of the adoption of this Act in 1872, was chiefly west of the Missouri River; it is impossible to locate a mining claim in most of our eastern states. It is true, however, that there are certain holdover rights, mostly obsolete, arising from the fact that at the time of the formation of the Confederation of States, the land that belonged to each state became the property of the Federal Government. I am not quite correc-t in that, it was sometime after the adoption of our Constitution, I think it was 1778, but those rights were largely, by agreement, surrendered to the Federal Government; but it is a fact that the great acquisitions of territory in the West, with the single exception of Texas, were of domain that came into the possession of the Federal Government and our Federal Mining Law applies to that territory. No state has the right to (by legislative enactment) enlarge upon the rights given by the Federal Mining Law, governing the acquisition of mining claims in its territory, within its boundaries. Each state, however, may, and some of them do, limit somewhat the rights given to the prospector. For instance, the Federal Mining Law provides that a claim may be taken, staked upon the public domain, of 600 ft. in width and 1500 ft. in length. Some of the states, like South Dakota and Colorado, have at times said "that is an excessive amount of land for a single mining claim; we will therefore limit it to 300 ft. or 200 ft. in width." There is, therefore, not any direct and immediate need for uniformity of mining laws in the United States, such as there might possibly be if it were considered at all desirable upon the whole in Canada. The initiation of mining rights under the Federal Mining Act is the act of discovery of valuable mineral in place, referring now to the lode mining claims, but the same is true of the placer claim. It is true that the emphasis has never been laid upon the word valuable and that

Jan 1, 1920

[ ] TEN FEET TALL and four feet wide, tire designed for Le Tourneau equipment is world's largest, and will operate with only 10 to 15 pounds air pressure. (15) SOIL SAMPLING: A complete collection of data about soil sampling techniques, accumulated during the past 33 years by the Acker Drill Co., is displayed in a 16-page bulletin. Modern sampling techniques are discussed along with recommendations as to correct tools and accessories best suited for economical recovery of samples. (16) GEAR MOTOR: U. S. Electrical Motors Inc. has a new bulletin on the type GW Syncrogear motor, showing phantom views of inner construction and operating detail. [ ] (17) SAFETY: A booklet containing an up-to-date list of American Safety Standards has been published by the American Standards Association. Comprehensive subject index and brief commentaries on the standards helps in selecting proper documents. Nearly all of the 160 American Safety Standards listed are widely used, and some have been adopted as a basic part of governmental codes.

Jan 1, 1952

One item of general interest in MINING ENGINEERING Trends, May 1952 gives the wrong impression of the scale of the ilmenite operations in North Carolina It also implies there are known deposits of rutile which "guarantee self-sufficiency for many years" So far as we know this is not true At present, rutile is in such short supply in the United States that the Defense Mineral Authority is encouraging prospecting for new deposits So far none have been found of any consequence and our needs have to be met largely from the deposits near Jacksonville, Fla, and rutile imported from Australia JAY P WOOD VICE-PRESIDENT HUMPHREYS GOLD CORPORATION The reference to self-sufficiency was meant to apply to the ilmenite-bearing sands, not rutile, but improper phrasing failed to make this clear However, the press release that the Glidden Co circulated stated that this deposit of ilmenite was one of the largest in North America -Editor

Jan 1, 1952

71 BROADWAY, NEW YORK, Sept. 22, 1913. CHARLES W. GOODALE, Chairman, . DARSIE C. BARD, ESQ., Secretary. Committee on Precious and Base Metals, Butte, Montana. Gentlemen The wonderful success of the meeting of the Institute held in Montana makes it necessary that some public acknowledgment should be made to those to whom this success is due. We are conscious that the securing of the great number of technical papers of lasting value and the carrying to success of most complete detailed arrangements for holding the meeting have called for several months of skilled effort on your part. The benefit of the meeting is very great and extends not only to those who were fortunate enough to be present, but to our four thousand absent members and their friends as well. To you and your associates on the Committee whose efforts have made this never-to-be-forgotten meeting possible we owe far more than can be expressed in votes of thanks. Very respectfully, CHARLES F. RAND, President.

Jan 10, 1913

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion ?).-Studies of the probable future production of oil wells and fields-particularly those in the nature of the recent work by Lewis and Beal, having the object of increasing the percentage of recovery-rank, in both practical and theoretic value, very high, if indeed they do not outrank all other petroleum investigations except structural surveys. Even such surveys, although saving untold millions that might have been spent in prospecting unpromising territory, may have less ultimate value than generally supposed, for it may perhaps be argued that much if not most of the condemned territory will sooner or later be tested-some is already productive-and the most that can be rightly claimed is the recovery of cream first; also that the consumption of the richest portions first cannot be extenuated, as it might with some resources, on the ground that if the best is not taken now it will deteriorate.

Jan 5, 1918

We did install one 100% brick bottom in our #33 furnace which is basically the same design as Inland's furnace. We had previously embarked on a program of replacing all bottoms in our 300 ton furnaces every 2nd campaign which would be about every 2000 - 2300 heats. This had been necessitated by the effect of our rather high oxygen blowing rates and our desire to maintain a minimum bottom interval level. This meant that we were able to compare bottom performance of various types of materials on a realistic bas is. Since furnace availability is critical to our operation, we are organized to employ every piece of equipment and all the necessary man power to complete a rebuild in the shortest possible time. A 300 ton furnace requires 7.5 days to rebuild. If a new bottom is to be installed an additional 2.5 days is added - 24 hours for tear out and 36 hours for bricklaying - making a total of 10 days.

Jan 1, 1972