Search Documents

By S. Whinery

I am indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of

Jan 1, 1913

By Murray F. Hawkins

One problem of reservoir engineering is the early estimation of the size of newly discovered reservoirs. Often these reservoirs are the expansion type in which sizeable pressure drops occur incident to the production of small fractions of the oil reserve, above the bubble point, and a material balance equation may be solved to find the reserve. The early form of this equation' considered only the compressibility of the oil. Later Hall2 showed that the compressible nature of the formation rock is a significant factor in production above the bubble point, and he presented a new equation which includes a formation (rock) compressibility term. This note presents a further extension of the material balance equation as applied to volumetric, unsat-urated reservoirs above the bubble point by including a term for the presence and compressible nature of the interstitial water. DERIVATION OF EQUATION During a decline in average reservoir pressure, ?p ?p, — p1 the initial reservoir volume V,, will decrease to some value V, due to the reduction in pore volume as a result of a decline in the hydrostatic pressure within the formation, and v, = V,, [l — cr ?p]......(1) The formation compressibility c, is expressed in terms of change in pore volume per unit pore volume per psi. Simultaneously the connate water within the formation expands from an original volume V,, = S,V,, to a new volume V,, V, = s,v,, [I + c,npl.....(2) The difference [Vp — V,] is the hydrocarbon pore volume at pressure p and may be equated to the volume of the remaining oil, or [N — N,] B, = V,,, [I - C~A;] - S,.Vpi [l + cwnjl.........(3) But the initial oil in place in terms of the initial reservoir volume, connate water, and formation volume factor is Ilividing Equation 3 by Equation 4 eliminates V,, to give,

Jan 1, 1956

ANDES, lying south of Chuquicamata and north of Braden on the western slope of Chile's cordillera, can best be described as a big well-managed copper-mining enterprise without any peculiarly outstanding features. In point of copper produced, since output started in 1927, it ranks fifth among the Porphyries, being exceeded only by its two Chilean contemporaries and by Utah Copper and Morenci in the United States. Even so, there is little to distinguish it from other properties. It does not have the phenomenally rich ore (better than 2 per cent copper) that characterizes Braden; and it is not in the same class as Chuquicamata whose ore has the excellent tenor of around 1.7 per cent, nor has it Chuqui's immense tonnage of proven ore reserves and potential ore resources. One might say the operations are standard in that there are no basic or radical departures from established practice. A letter from New York supplying me with sundry pertinent facts for which I had asked, makes this comment regarding the answer to one inquiry: "omitted because it is the ordinary equipment found in any well-run mine." The substance of that remark applies generally to the other operations, plants, and facilities. One interesting fact that helps explain this situation should not be overlooked. Until the "new" Morenci in 1942, Andes was the last of the Porphyry copper mines to come into production. It did not do much pioneering because other companies had, of necessity, charted the way in many particulars. The company was organized by the Anaconda Copper interests in 1916 to take over a, group of claims held under option by William Braden who, a few years earlier, had interested

Jan 1, 1957

By Edgar Bain

OF THE important phenomenon of the hardening of steel, Professor Sauveur1 says: "It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem.. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say, this of other problems. It seems likely that one of the new avenues of approach to many metallographic problems is the study-of crystal structure, or more accurately, the atomic arrangement by means of the X-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of X-rays by Laue and the Braggs2 and later by Hull,3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the X-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 2, 1922

Discussion of the paper of L. C. Graton and Joseph Murdoch, presented at the New York Meeting, February, 1913, and printed in Bulletin No. 77, May, 1913, pp. 741 to 797. THOMAS T. READ, New York, N. Y. (communication to the Secretary *) :-At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper 1 on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows : ?The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a wade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 10, 1913

By Frank Firmstone

Discussion of the paper of John B. Dilworth, presented at the Pittsburg meeting, March, 1910, and printed in Bulletin No. 35, November, 1909, pp. 1041 to 1043. FRANK FIRMSTONE, Easton, Pa. (communication to the Secretary*) :-Mr. Dilworth's formulas and tables are of course correct, and the extinction will occur as calculated, provided the money periodically set aside for sinking-fund be really invested. and the interest compounded as assumed in the calculation. Actually, in almost all cases, such funds are used "in the business," in which case, in addition to the periodical charges for principal of the fund, additional charges must be made at the end of each period to cover the interest and compound interest on previous charges. The periodical charge for sinking-fund thus becomes a varying and continually increasing one until the date of extinction. On many accounts it seems more natural and convenient to make the extinction by a fixed periodical charge under the legal rule for partial payments, namely, that each payment should apply first to the interest due at the date of payment;: and any remainder, after this is satisfied, be deducted from the principal before the interest for the next period is calculated. The formula below is convenient for such calculations S, Principal to be extinguished. Q, Periodical payment or charge for sinking-fund. B, Balance unpaid at date of nth payment, but before that payment is made. r, Rate of interest per period per cent. n, Number of payments or periods. Then, B=S(1+r)n-Q(1+ r)n-(1+r) Received July 27, 1910.

Apr 1, 1911

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials; it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted.

Jan 3, 1918

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By D. C. Anderson

Utah Construction & Mining Co.'s Lucky Mc mine is one of the major uranium producers in the United States. It is located near the geographic center of Wyoming in Fremont County. The climate is middle-latitude steppe, with an average annual precipitation amount of 10 in.; the temperature varies from 40º below zero to 100º above. The land surface is moundlike, rolling terrain, with sparse grass and sagebrush. The northern slopes of the higher ridges support a scattering of juniper and pi[n]ion growth. DISCOVERY The discovery was made by Neil E. McNeice, of Riverton, Wyo., on Sept. 13, 1953. After prospecting the area and staking a few claims, McNeice reported his findings to geologists of the Atomic Energy Commission (AEC), who immediately began preliminary studies of the numerous surface uranium exposures of the district. The discovery received widespread publicity, resulting in an intensive search for uranium throughout the region ; thousands of claims were staked. The AEC drilled several shallow holes near the discovery outcrop. Assays of cuttings from these holes confirmed the presence of a low-grade, oxidized uranium deposit. McNeice and his partner, L. A. Morfeld, tried to start a mining operation but were plagued by a lack of capital and technical know-how. They sought assistance from a Salt-Lake-City-based mining firm, the New Park Mining Co., engaged in underground base-metal mining in the Park City district of Utah. After a period of negotiations, New Park initiated activities that led to the forming of the original Lucky Mc Uranium Corp. The company started limited development drilling and mining operations in the summer of 1954, with the first ore production being shipped by truck to the Vitro mill in Salt Lake City. The mining

Jan 1, 1969

By C. M. Weld

The southeastern coast of China, from Ning-Po to .Macao, represents an element in the continental mass of Asia which has at practically all times in the remote past exhibited a tendency to rise rather than to subside.' This strip of land, 1,000 or more miles long by perhaps 150 miles wide at its widest part, has in fact stood above sea level since at least early Cambrian times, while the great basins to the north and west were receiving their massive accumulations of Sinian (Cambro-Ordovician), Carboniferous, and later deposits. We find, .therefore, a coastal fringe of metamorphic and igneous rocks bordering the huge expanses of sedimentary rocks which occupy the interior. Hong-Kong is situated toward the southwestern extremity of this fringe. Hong-Kong is an island of approximately 30 sq. miles, on the north shore of which is situated the city of Victoria, with its 325,000 inhabitants. This island was ceded to Great Britain in 1842. In 1560 the peninsula of Kowloon (about 5 sq. miles), being that part of the mainland lying directly across from the city of Victoria, was added to Hong Kong. Thirty-eight years later, in 1898, a stretch of territory, including the mainland behind Kowloon and. numerous adjacent islands, was leased to Great Britain for 99 years. This last addition is known as the "New Territory of Hong-Kong" and comprises 376 sq. miles in area. A map of Hong-Kong, Kowloon, and the "New Territory" is shown in Fig. 1. My studies of this total area of over 400 sq. miles were devoted primarily to an investigation of the mineral resources. Systematic mapping of the immensely complex exposures of rocks was not possible in the time at my disposal. However, observations in, this. direction warrant a few generalizations.

Jan 2, 1914

The problems associated with the processing of the Tilden ore are very much representative of the problems encountered in plants processing fine grained magnetic and nonmagnetic iron ores. I would like to comment on some of the problems mentioned in Dr. Nummela'spaper and add to his list of research opportunities in the processing of iron ores. Grinding, the most important step in the processing of fine grained iron ores, is synonymous with liberation. One grinds to separate discrete grains of minerals from the gangue. By convention- al grinding in tumbling mills, mostly random size reduction is achieved with relatively little preferential liberation of minerals. Not only are discrete particles broken that should not be broken, but damage is done to the mineral surfaces. The combination of over- grinding and surface damage shows up in lower recovery figures and higher grinding costs. What is obviously needed is a better comminution process that is more discriminating and that would permit liberating mineral particles at the coarsest possible size with a minimum production of fines. Laboratory attempts at such preferential grinding have been quite successful, but technological difficulties have unfortunately prevented its use. Impact grinding is a good example of a new comminution process that has not been accepted because of equipment problems. Either these problems have to be solved or new comminution systems have to be developed to reduce grinding costs and improve liberation. In his paper Dr. Nummela mentions the change in the primary mill throughput that occurs during the winter months. Seasonal changes in the operation of the grinding circuit and other unit operations have been observed in many plants, and many explanations for this phenomenon have been advanced. The fact is that we do not fully

Jan 1, 1979

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

By Robert Franke

In view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in. For the ore of this mine, a moderately hard but very fissile schist,

Jan 1, 1914

EUGENE WESLEY SHAW,* Washington, D. C. (written discussion?).-Mr. Requa's subject is one of great economic importance, yet relatively new, and he has been able to combine extensive practical experience with the talent of grasping the broad features of a problem that has many discordant details.

Jan 5, 1918

By John C. Bilello

The brittle fracture behavior of cold-worked sintered tungsten was studied over the temperature range 4.2° to 298°K using a high-sensitivity strain measuring system and electronfractography. Similar observations were made on a swaged electron beam zone-refined monocrystal. In sintered tungsten irreversible plastic deformation was observed during cyclic load-unload tests at stress levels well below the fracture stress for all temperatures, but general microyielding could be detected only down to 202°K. For the zone-refined samples macroyielding occurred at all test temperatures with evidence for twinning below -202°K. The fracture stress of the sintered tmgsten was virtually independent of temperature, while the zone-refined crystal showed a 2.3 times increase over the same temperature range. Electronfractography confirmed the presence of numerous rod-shaped and spherical submicroscopic voids which ranged in diameter from 1400 to 4300A in the sintered tungsten; no voids could be found in the zone-refined tungsten. Contrast effects observed on the replicas in the vicinity of certain voids indicated that plastic deformation could be induced by the local stress concentration. It has been suggested that the presence of these voids may be responsible for the low-temperature brittle failure of sintered tungsten. Based m this suggestim und on the evidence obtained here, a dislocatim model is presented to account for the brittle behavior of sintered tungsten. In this model slip, which is induced by the local high stress concentration in the region at the edge of a favorably oriented void, could cause the void to grow to a microcrack of critical size. STUDIES of brittle fracture in bcc metals have led to the well-known experimental relationships between grain size, yield stress, fracture stress, and temperature which have formed the basis for the various dislocation pile-up1-3 or interaction4'= models for slip-induced microcrack nucleation. While microcracks can be nucleated by deformation twins,6,7 there has been no direct evidence furnished by transmission electron microscopy to support conclusively either the Zener pile-up or Cottrell dislocation reaction models for producing micro-cracks in all "brittle" materials. In addition to the "inverse" grain size relationship for yield and fracture stresses the cottrel14 theory predicts that the fracture stress below the transition temperature should behave in a fashion similar to that of the yield stress above this temperature. Such behavior has been verified for several bcc metals.8-10 With reference to both grain size effects and the tem- perature dependence of the fracture stress below the transition temperature, the behavior of sintered tungsten appears anomalous. Early work by Bechtold and Shewrnon 11 showed no apparent temperature dependence of the fracture stress below the ductile-brittle transition temperature (DBTT). They attributed this result to the intergranular nature of the fractures observed. More recent work by Wronski and Four-deux12'13 on considerably purer material did not show any systematic relationship between the fracture stress and temperature below DBTT. The dependence of flow and fracture stresses on grain size is also not clearly established for sintered tungsten. Koo, for example, has shown that the DBTT for sintered tungsten depended chiefly on the annealing temperature and was relatively insensitive to the actual grain size achieved. Using electrofractography and transmission electron microscopy, Wronski and Fourdeuxl3 showed that numerous spherical and rod-shaped submicroscopic voids could be found in sintered tungsten but not in melted tungsten of nominally the same purity. They suggested that these voids could be responsible for the temperature insensitivity of the fracture stress below the DBTT. In the present work the temperature dependence of the fracture stress for high-purity commercially sintered tungsten has been determined. The presence of submicroscopic voids in sintered materials was confirmed, and these were studied in detail to examine the role they could play in nucleating brittle fracture. A dislocation model is suggested which could cause an inherent spherical void to lengthen into a Griffith crack of critical size. EXPERIMENTAL PROCEDURE Commercially sintered tungsten rod was obtained in the as-swaged condition from Sylvania. A zone-refined crystal was obtained from the same source. This crystal was grown by giving three zone passes (at 25.4 cm per hr) to a sintered rod of high-purity tungsten. The rod axis prior to cold working was -15 deg from the [110] direction. Originally the zone-refined rod was -6 mm in diam; it was reduced to -3 mm by eight swaging passes, at high temperatures, with each step having about the same reduction of area. The final swaging step gave a 7.5 pct reduction of area at 1050°C. All swaging operations were performed in a hydrogen atmosphere. For the sintered rod a similar working schedule was employed. Metal-lographic examination of the sintered material revealed that the cold-worked structure had an apparent grain diameter of -25 u transverse to the swaging direction (obtained by the intercept method). In the longitudinal direction cold-worked grains were approximately 1.5 to 2 times their diameter. No distinct fiber structure could be observed optically for the zone-refined rod. The cold-worked structure in the

Jan 1, 1969

Extractive Metallurgy Division Institute of Metals Division Iron and Steel Division OFFICERS AND COMMITTEES John Chipman, President W R Hibbard, Jr, Past President C C Long, Vice-President T D Jones, Treasurer R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1959

By R. A. Spurling, C. G. Rhodes

SATISFACTORY metallographic sample preparation of very soft metals, such as lead and its alloys is generally difficult. The prime requisite of any technique must be that the result gives an undis-torted microstructure for the microscopist to examine. A small amount of mechanical polishing followed by a chemical or electrolytic polish is usually the most desirable way to obtain an undis-torted surface. Several chemical-4 and electrolytic3-' polishing solutions have been developed for dilute lead alloys. Perchloric acid mixtures (with acetic anhydride, ethyl alcohol, or water) are among the most prominent electropolishing solutions used for lead; however, the presence of bismuth in the alloy precludes the use of any perchloric-containing solution. The other solutions1-7 were found to be unsatisfactory on alloys ranging from 10 to 65 wt pct Bi in lead. With increasing bismuth content, the microstructure shows a lead (terminal solid solution), 0-6 mixture, E (peri-tectically formed hexagonal phase), and E bismuth mixture (eutectic at 56.7 wt pct Bi).9 The metallographic samples were mounted in "Araldite" epoxy (the heat generated during polymerization does not alter the microstructure), ground by hand on well-waxed silicon carbide papers (400 and 600 grit), and polished with 3- and 0.25-CL diamond paste on billiard and microcloths, respectively. The use of the various polishing and etching solutions reported in the literature resulted in the formation of irremovable reaction products on the sample surface when applied to "as-ground" or "as-polished" surfaces. The E phase was the most difficult to clean chemically and in the development of an etchant for this system several solutions which satisfactorily etched the bismuth or a phase were unacceptable because of their reaction with the E. It was found that a mixture of 50 ml lactic acid 30 ml nitric acid 20 ml (30 pct) hydrogen peroxide (Solution #1) was a satisfactory etchant for the a-matrix alloys. The samples were prepared as before and etched after 1 min of polishing with 3-p diamond paste. The etchant was applied by swabbing (light pressure) for 30 sec to 1 min and the sample was then rinsed in running water. The E has a slight stain and the a is fairly bright, Fig. 1.

Jan 1, 1965

By Arthur Braid

THE war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be. obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find-in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the- manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain- grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferro-manganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within 'the last few years, and particularly since the war began, the great value of manganese in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 11, 1918

By Harold H. Goe, Louis V. Bender

The recovery of arsenic was started at the Washoe Reduction Works (later called the Anaconda Reduction Works) in 1904, when an arsenic plant was constructed adjacent to the lower end of the 60-ft. main flue.' This plant originally consisted of a Brunton roasting furnace for treatment of flue dust and a small reverberatory furnace for treating the crude arsenic produced in the roasting operations, together with the necessary kitchens for condensation of the fumes and grinding and barreling apparatus for preparing the refined white arsenic for market. The Brunton furnace was fired with wood. It was 14 ft. 6 in. in diameter with two outside fireboxes. The hearth revolved upon a central shaft. The charge was fed through a dust-tight hopper on to the center of the hearth and slowly moved to the outer edge of three rows of stationary rabbles fastened in the roof of the furnace. There was a 3-ft. space between the hearth and roof. A crude arsenic was condensed from this furnace. The hot flame from the fireboxes passed directly over the charge, vaporizing the As203 that was carried through brick flues to the condensing chamber. This chamber was 8 ft. high, 16 ft. wide and 240 ft. long, divided into small kitchens by partitions spaced every 7 ft. It was connected with the main flue system to provide draft and to receive any losses from the chamber. The small kitchens were connected by openings in such a way that the fumes took a zigzag course, causing them to come in contact with the cold walls and ceiling and condense the arsenic. There was an opening from the outside into each kitchen, for the removal of the deposited arsenic, which was closed by a wooden door. The refining furnace was a small coke-fired reverberatory having a hearth 10 by 20 ft. in dimensions. It had three hoppers through which the crude charge was introduced, and one firebox placed at one end. The hot gas from the burning coke passed over the charge, volatilizing the arsenic and carrying it to the kitchens.

Jan 1, 1934