Search Documents

By F. M. Perkins, R. H. Jamison

Publications concerning scaling laws for laboratory flow models of oil reservoirs indicate that the relative permeability and capillary pressure relations must be the same functions of saturation in the model and its prototype. In this paper, the relative permeabilities and saturations are redefined in a way which permits one to have diflerent relative permeability and capillary pressure relations in the model and prototype. The development of the new scaling criteria is demonstrated by deriving scaling laws for one simple flow problem. INTRODUCTION The successful application of information gathered through bench-scale model studies to the prediction of multi-phase fluid flow behavior in petroleum reservoirs requires careful consideration of the scaling criteria. The requirements which must be met for a small-scale model to duplicate the behavior of a much larger reservoir prototype have been discussed by Leverett, et al,' Rapoport,2 and Geertsma, et al.3 According to these authors, the relative permeabilities to water, oil and gas and the dimensionless capillary pressures must be the must have the same values in the model and prototype. Furthermore, they point out that the viscosity ratios must have the same values in the model and prototype. In addition to these requirements, other scaling criteria are given which, when considered, usually dictate a much higher permeability in the model than exists in the reservoir. Since the more permeable model sands may have connate-water and residual oil saturations quite different from those in the prototype, the scaling requirements pertaining to the dependence of relative permeabilities and dimension l ess capillary pressures on saturation usually are not met. Also, if the model fluids are selected to give equal viscosity ratios in the model and prototype, one may find greatly different mobility ratios* in the two cases and, therefore, may expect grossly different flow patterns. For this reason, Craig, et al,' correlated the results of their model studies with mo- bility ratio rather than with viscosity ratio. As yet, however, no satisfactory method has been advanced which permits use of anything other than the scaling requirements outlined in the previously mentioned papers. The purpose of this paper is to present a method of developing a set of scaling criteria which permits different relationships between saturation and relative permeability or capillary pressure in the model and prototype. Rather than attempt to report scaling criteria for a variety of practical situations, this paper demonstrates by use of one simple example how the modified scaling criteria are derived.

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By Arnulf Muan, Hobart M. Kraner

Ferromanganese alloys react with aluminu-silica brick in blast furnace hearths and cause the formation of new phases with low refractoriness and consequent failure of the refractory lining. The nature of these reactions is explained on the basis of petrographic observations, thermodynamic data, and Phase equilibrium considerations. Animproued hearth design resulted from these findings. The production of ferromanganese in blast furnaces presents many problems which are not encountered in the production of iron in the same furnaces. One of the most serious of these problems is the rapid failure of refractories caused by their reaction with the ferromanganese metal. The present paper describes such a "hearth attack", its symptoms, causes, and cure. Following an introductory discussion of operating practice in ferromanganese blast furnaces, results are presented of a petrographic examination of samples from a furnace which had to be shut down because of refractory failure. The causes of this failure are then analyzed on the basis of petrographic observations combined with thermodynamic and phase equilibrium data available in the literature. The latter type of data were subsequently used as a guide in recommending improvements in hearth designs which have since proven themselves successful in practical operations. I) FERROMANGANESE BLAST FURNACE PRACTICE It is considered good practice to blow in a furnace on iron and operate it in this way for a period of time preliminary to producing ferrornanganese. During this time, iron generally penetrates the bottom refractories six or more feet below the original working surface of the hearth. Not only does this metal pervade the joints to these depths, but the pores of the refractories are usually also filled by molten iron. The high throughput of the iron furnace provides ample heat to maintain a high temperature in the hearth refractories. This, together with a high ferrostatic pressure, causes porous clay brick of the hearth to shrink. During subsequent use of such a furnace in ferromanganese production, the iron in the pores of hearth brick if; replaced to some extent by ferromanganese. The replacement is usually not complete. This is probably due to the lower metal throughput and lower prevailing temperatures resulting from this in the brick of the hearth bottom. When the ferrornanganese furnace is banked—or when the temperature in the furnace falls due to a furnace delay—-manganese oxidizes even though the atmosphere is largely CO. Considerable expansion accompanies this oxidation of manganese from metal to oxide. The hearth refractories are then subjected to the disintegrating forces of the volume expansion. These forces may in extreme cases be large enough to lift the furnace off its mantle supports as was described in a previous paper.' When cooling takes place slowly, however, and the temperature remains at a fairly high level, the refractories undergo fluxing action by the MnO. This latter reaction and the reduction of SiO2 of the clay brick is the general subject of the present paper. The observations to be described herein were made on a ferromanganese furnace located at the Johnstown plant of Bethlehem Steel Co. The furnace was lined entirely with clay refractories and had operated on iron for 266 days and on ferromanganese for 96 days prior to being taken off because of a hearth wall failure. II) PETROGRAPHIC EXAMINATION AND CHEMICAL ANALYSIS The photograph reproduced in Fig. 1 shws a cross section of the upper part of an 18 by 9 by 4-1/2 in. bottom block removed from the blast furnace. This brick came from a depth of approximately 6 ft below the original working face of the bottom. It will be noted that the 4-1/2 in. dimension is almost the same as when the brick entered the furnace. Three characteristically different zones marked I, II, and III on the print of Fig. 1 are apparent. Results of chemical analyses of the original brick and samples from each of these zones are listed in Table I. Petrographically the various zones were characterized as follows: The central zone marked I was essentially un-reacted brick. The microstructure consisted of fine needles of mullite, and the pores in this entire area were filled with iron. This is characteristic of

Jan 1, 1962

By Louis V. Bender, R. E. H. Pomeroy, David H. Browne

E. P. Mathewson, Anaconda, Mont.—After hearing about the success of D. H. Browne with his furnaces, we in Anaconda decided we might venture into the field of pulverized coal for reverberatory smelting. We sent a delegation of investigators to see Mr. Browne and his work, and they returned, filled with enthusiasm, and said they would recommend it strongly.. We thereupon asked for an appropriation, and after some delay obtained the same and fitted up one furnace to use pulverized coal. We copied Mr. Browne's practice and his selection of machinery for drying and pulverizing coal; and we also copied the burner he used, which was a standard article on the market. We got an expert coal-dust machinery man to design our plant, and were very glad we did so as we avoided some of the unpleasantness that had been experienced at other plants through fires and minor explosions. I want to say, before describing our apparatus a little in detail, that we were quite familiar with the work of Mr. SÖrensen, the pioneer in the use of pulverized coal for copper smelting. Our attention had been called to it by Mr. Klepetko early in the game. And afterward we were familiar with the work done at Cananea by Mr. Shelby. We sent an expert to investigate the question 10 years ago. He examined the work of Mr. SÖrensen; and then went to the cement men and examined their work, and reported at great length that coal dust was the ideal fuel for them, as they took the ash from the coal and sold it as cement. He reported that coal-dust firing could not be made economical in reverberatory copper smelting, and his reasons were that a blanket of nonconducting material would cover the charge in a short time and insufficient heat would reach the charge proper, and we would have floaters over all our furnaces. The flues would be stopped by the dust that did not settle on the charge. We accepted that until our Irish friend got busy and showed us how to do it. Then we built a furnace which we thought was a slight improvement over Mr. Browne's. We put railroad tracks over our furnaces to draw the charge to the furnace. We had

Jan 1, 1915

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By Walter Hull Aldridge

Much has been said about the foreseeable exhaustion of known mineral reserves-particularly in the United States. It is claimed that we are about to become a have-not nation insofar as certain essential minerals are concerned; and in this respect our position is often contrasted with that of the world as a whole, largely because we have drawn so heavily on our domestic resources during the last fifty years. As a matter of fact, the difference is not great if one takes a reasonably long-term view of the situation. No one denies that nature endowed the United States richer in mineral resources than any other equal area. It is granted that we have skimmed the cream of many kinds of minerals; but in a free international trade in minerals it would not be many decades before the richer deposits-at least the deposits easy of discovery throughout the world would be depleted to much the same degree as those in the United States today. For it is a fact that the problem of satisfying the needs of our industrial society for minerals is fundamentally worldwide in scope. The singular and significant attribute to all minerals is that there is but a single crop. Forests can be grown, but mineral deposits can be replaced only by finding new ones. Thus, one of the vital tasks of the mining engineer, the petroleum engineer, and the geologist is to find these new mineral resources. Another task is to devise means and methods for the exploitation of, at costs that are economic, low-grade deposits and those deeply buried in the crust of the earth. The first need, however, is to find the deposits in the ground. If the assumptions of those who today fear an early exhaustion of all deposits are valid, the outlook for continued material and social progress is gloomy indeed. I take a more optimistic view, for it is my belief that vast new sources of needed minerals will have come to light before our known resources are gone. The real question is whether the outside layer of the crust of the earth that is accessible to engineers contains adequate mineral deposits; and whether engineers can find those deposits. The answer must be based on geologic science, geologic fact, and mining history. Every continent, and almost every country, has yielded minerals of industrial utility in substantial quantity. Mineral deposits are widespread. Geologists know the conditions that were favorable to the occurrence of ores and the types of rocks in which various kinds of ores may ordinarily be found. They know that such rocks occur over broad regions of the earth's surface. They also know that in large areas rocks that are potential carriers of ores are covered and concealed by material of entirely different character. Such cover may consist of lava flows, layers of volcanic ash, or beds of material washed down from the surrounding mountains. Sometimes those covers are thick, sometimes relatively thin. But men well-qualified to pass judgment are sure that concealed deposits, large in number and in size, exist close enough to the surface to make exploitation practical. Only by actual penetration of the surface can this contention be proved, but to conclude otherwise would be to ignore the laws of probability and to deny the over-all consistency of nature. The task of probing the crust of the earth to determine the location of these deposits, and to obtain some notion of their size and quality, poses serious problems. However, they should not be beyond human solution. Much more research must be done in analyzing and explaining the laws of ore deposition. New tools, in the shape of techniques and methods and of mechanical and electrical devices and instruments, must be developed. But no reasonable person can doubt that these objectives will be achieved. As the need becomes increasingly pressing, scientists and engineers will supply the imagination and the ingenuity that will provide the solution. The time and effort thus far devoted to the development of methods for locating hidden ore bodies have been pitifully meager. Energetic investigation of the subject of applied geophysics is essential to the success of the mineral industry, and I have no hesitation in predicting that effective techniques will be found and successfully applied. Twenty-five years ago the petroleum industry

Jan 3, 1950

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations.. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which, if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its use is, however, confined to a person having skill in the manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms—the call-bell—has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanche cells, two or more electric bells, and a mile or more of mire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By ELLSIVOKTH DAGGETT

THE Berlin gold quartz mine is situated in Nye county, Nevada, on the west flank of the Shoshone range, about 40 miles south and 30 miles west from the town of Austin, the county-seat of Lander county. The distance from Austin is about 60 miles by stage-road. The outcrop of the vein, at the top of the incline-shaft, is situated just at the base of the mountain proper, almost exactly at the intersection of the mountain-side with the gravelly bench that slopes for about three-quarters of a mile to the flatter sage-brush plain, or desert valley, below. The -vein itself consists almost entirely of quartz, with perhaps 2 per cent. of sulphide of iron, copper, lead, zinc and antimony, and perhaps a trace of some of the compounds of tellurium with gold and silver, although none of the latter have been as yet positively identified. The relative proportion, by weight, of silver and gold in the ores, varies in different parts of the vein, from 12 silver for 1 of gold, to 7 silver for 1 of gold. The quartz vein-filling is usually frozen fast to the walls, and is very hard and compact, seldom showing the friable, fissured, or shelly structure often to be found in quartz veins. Comparatively little evidence of relative motion of one wall of the vein upon the other is to be found-a fact indicating that during the formation of the vein, and prior to the extensive movements herein described, little disturbance had taken place. No evidence whatever of metasomatic origin has been observed. On the other hand, occasional occurrences of comby structure, in which the axes of the quartz crystals are at right angles to the plane of the vein, rather indicate deposition from solution in a pre-existing fissure. Spurs, or branches, and small parallel veins, while not en-\

Mar 1, 1907

By J. J. Gilvarry, B. H. Bergstorm

The first part of this paper describes a new approach to the problem of energy relationships in fracture and comminution. The basic theoretical method used (as contrasted to previous empirical or semi-empirical approaches) is an attempt to verify or disprove the hypothesis of von Rittinger, In the second part of the paper, theoretical conclusions for the three headings of single fracture, plural fracture, and comminution are tested. Agreement between theory and experimental results is demonstrated. The classical hypotheses on the energy relationship in brittle fracture are those of von Rittinger-that the energy required is proportional to the new surface formed— and the alternative one of Kick.' Over the years, repeated attempts have been made to discriminate experimentally between the two assumptions, or to replace both of them, as has been done by Bond? However, no semblance of agreement seems to exist among different investigators. This paper is the first in a series essaying a new approach to the entire problem of energy relationships in fracture and comminution. The purpose of this program of research is to verify (or disprove) the hypothesis of von Rittinger. In contrast to previous empirical or semi-empirical approaches to the problem, the basic method adopted is theoretical. The prime aim is to determine the distribution function for fragment size theoretically and to verify the predicted distribution experimentally. This approach should make possible determination of the total surface of the particles by integration over the corresponding distribution function; one may hope that this direct procedure will yield more definitive results than use of gas adsorption or other methods. The surface area so obtained can then be compared with experimental energies, as obtained by Bergstrom, Sollenberger, and Mitchell,4 for example. It is convenient to distinguish between single fratture, plural fracture, and comminution. Single fracture of a brittle solid is defined as fracture by an external stress system which is removed instantly and permanently when fracture is initiated. Plural fracture consists of single fracture of the original specimen, followed by a sequence of only a few secondary fractures; comminution differs in that the sequence of secondary fractures consists of a large number of repetitive steps. For single fracture, Gilvarrys has given a rigorous derivation of the proper distribution function for fragment size, based on a closely defined physical model and deduced strictly by the laws of probability. Gilvarry and Bergstrome have compared the predictions of the theory with experiment, and have found excellent agreement. The prior work of Gilvarry and of Gilvarry and Bergstrom considers only single and plural fracture. The purpose of the present paper is to extend the discussion to the case of comminution. For prefatory purposes, the theory of Gilvarry for single fracture will be outlined. The considerations will then be applied to the cases of plural fracture and comminution. SINGLE FRACTURE The derivation is based on the Poisson law.7 For Points distributed with mean density y over a domain, this law states that the probability p(t)dt of one point lying in the range t to t + dt with none in the interval 0 to Ms p(t)dt = ye-yt dt. For this distribution to be valid, it is necessary and sufficient that the points be distributed at random, individually and collectively in the sense of ~~~.7 The former qualification requires that the position of One Point be independent of another, and the latter implies that the probability of a region containing a

Jan 1, 1961

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.'-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By G. R. M. Del Giudice, A. F. Taggart, Othon A. Ziehl

In a previous paper1 in which one of the authors collaborated, it was postulated that All dissolved reagents which, in flotation pulps, either by action on the to-be-floated or on the not-to-be-floated particles affect their floatability, junction by reason of chemical reactions of well recognized types between the reagent and the particle affected. This generalization, apparently, like many pioneer structures, had for certain observers a flimsy appearance, and these, judging its stability rather by the number than by the character of its foundation posts, have attempted variously to overthrow it, either by the frontal attack of general denial, or by the flanking movement involved in assuming that those cases in which the facts were unknown or unproved were, therefore, discordant. But as time has passed and further evidence on the question has accumulated, it has become apparent that the results of verifiable experiments add stone by stone to the substructure of the hypothesis, and that the super-tructure has lost nothing in weathering. The present paper constitutes an examination of the opposing positions in the light of the more recent evidence developed. It will clarify the discussion if, at this point, we state more fully the implications of the disputed hypothesis. In the first place, it is explicitly limited to reagents that are dissolved in the water of the flotation pulp. Next, it refers only to such of these dissolved reagents as act on the solid particles in the pulp to affect their floatability. This includes the collectors, activators, and certain depressors and gangue-control reagrnts, but not the pure frothers, and not, necessarily, conditioners whose function seems to be merely that of pH control, although in certain cases it has been demonstrated that such control has the effect of regulating the primary reaction of the collector, depressor, or the like. Finally, there is no limitation as to the nature of the chemical reaction postulated.

Jan 1, 1935

By Frank C. Smith

THE following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Gold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Arizona, which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerals were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables were elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By B. N. Thompson

Main industrial minerals produced in New Zealand are nonmetallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. Other minerals, some with minor production, include diatomite, feldspar, magnesite, sulfur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example, clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of late Cenozoic acidic volcanic rocks.

Jan 1, 1984

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By C. D. Michaelson

The memory of D. C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was immeasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War II, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling's remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential.

Jan 4, 1969