Search Documents

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By Isabella Faria da Cunha Peixoto

O emprego das ligas NiTi proporcionou a fabricação de instrumentos endodônticos com diferentes desenhos de lâminas cortantes. Este estudo investigou a relação entre as características geométricas destes instrumentos e a força apical necessária para inseri-los em canais artificiais em blocos de acrílico. A força apical foi registrada através de um dispositivo de bancada de testes. Dez instrumentos de cada tipo ES, Mtwo, ProFile GT, ProFile GTX, K3, RaCe e PTU F1 foram testados a uma velocidade de 300 rpm e um torque de 5 Ncm com um movimento vertical de 17 mm de comprimento. Os dados foram comparados por análise de variância (a = 0,05). Avaliação geométrica e dimensional mostrou que o instrumento K3 tem a maior área de seção transversal, seguido por PTU F1 e GT. Os ângulos helicoidais menores de RaCe, ES e GTX podem ter contribuído para os baixos valores de força apical encontrados. Maiores valores de força apical foram determinados nos instrumentos GT, K3 e PTU F1 em relação à RaCe, ES e GTX. Foi observado que a força apical exercida durante o preparo do canal está diretamente relacionada à área de seção transversal e aos valores dos ângulos helicoidais dos instrumentos.

Aug 16, 2017

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Valdeci Paula Alvarenga

Foi desenvolvida uma mistura briquetada utilizando escória recirculada, gerada no convertedor MRP-L e finos de fluorita para substituir a fluorita granulada no refino primário do aço SAE1012 na Aperam. A utilização desse briquete permitiu a substituição parcial da fluorita granulada, importada, sem prejudicar as reações de descarburação e desfosforação, mantendo as mesmas condições físico-químicas da escória. A qualidade interna dos aços produzidos, usando este novo insumo, permaneceu inalterada, atendendo a todas as exigências especificadas para os produtos.

Jul 30, 2018

By Sébastien Gérardin

Developed for more than 30 years, continuously improved, cored wire is nowadays a reliable solution for the improvement of sustainability, safety, health and doing quality and cost saving. Cored wire allows the addition of ferroalloys and treatment of liquid steel, especially concerning the calcium treatment. Amongst all the processes in secondary metallurgy, calcium treatment is certainly the most critical one before casting. Besides the traditional CaSi and CaFe wires, new types of wire have been designed for becoming the new reference in calcium treatment. PapCal (calcium insulated wire) and HDx (high density calcium wire) are a very versatile range of products. Indeed, according to the steelmaking process parameters (steel grade, treatment temperature, ladle size, calcium content targeted in tundish and even injection conditions), their technical specifications may be adapted in order to optimize the calcium treatment as high as possible.

Aug 16, 2017

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By José Aparecido Pereira

Em um laminador de barras e perfis leves (MBQ) é necessário ter um padrão técnico corretamente elaborado a fim de facilitar a preparação do câmbio e tornar o ajuste de bitola (set up) mais rápido gerando o mínimo de sucata e de produto fora da especificação de qualidade. Para se chegar ao padrão diversas etapas necessitam ser cumpridas para se ter um resultado confiável e uma ferramenta de trabalho acessível e de fácil entendimento pelos operadores do laminador. A Engenharia de Processos cuida de todas as etapas deste trabalho e também adota métodos para que o processo de produção se mantenha estável e com boa produtividade.

Aug 16, 2017

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Willy Ank de Morais

Este trabalho teve como objetivo analisar, através da fractografia, o desempenho de aços inoxidáveis Duplex 2205 soldados por três processos diferentes: FCAW - Flux-Cored Arc Welding (Arame Tubular), o GTAW - Gas Tungsten Arc Welding (TIG), e o SMAW - Shielded Metal Arc Welding (Eletrodo Revestido). A superfície de fratura das amostras foi obtida através de ensaios de tração, nos quais foram registradas as respectivas curvas tensão-deformação completas, que também foram analisadas. Os resultados mostraram que o tipo de influência da solda nas propriedades mecânicas analisadas.

Oct 30, 2017

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By Fernando Vital Silva

O processo de lingotamento contínuo consiste de uma série de etapas que promoverão a extração de calor de maneira controlada do aço líquido, com o objetivo de promover sua solidificação. Uma vez que a solidificação é considerada uma transformação de fase, regida essencialmente pela troca térmica, o enfoque do processo de lingotamento contínuo se encontra direcionado para o perfil térmico de resfriamento do aço desenvolvido ao longo dos veios da máquina. É extremamente importante para a qualidade final do tarugo que este processo de extração de calor ocorra a taxas controladas, de maneira contínua e uniforme em todas suas faces. Segregação, trincas e romboidade são alguns dos problemas de qualidade que podem ser originados devido a um controle não assertivo ou deficiência do sistema de refrigeração. Os tarugos lingotados do aço 1545-D, produzidos na máquina de lingotamento contínuo da Votorantim Siderurgia Barra Mansa, apresentavam com frequência trincas sub-superficiais nas quatro direções de resfriamento e a uma distância constante da superfície do tarugo. Através de equações de solidificação foi constatado que a profundidade em que as trincas se encontravam nos tarugos correspondia a um trecho da máquina no qual existia gap de refrigeração, provocando reaquecimento do material e o surgimento de trincas devido ao regime de contração/dilatação ao qual o mesmo estava submetido. Tais conclusões permitiram comprovar falha no projeto de refrigeração secundária da máquina.

Jul 30, 2018

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Uazir Bezerra de Oliveira, Günther Staudinger, Michael Skorianz, Edo Engel

Oct 1, 2019

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Daniel Hiroshi Taira Anese

O objetivo desse trabalho consiste no estudo do grau de sensitização do aço UNS S31803 envelhecido a 700ºC por ensaios de reativação potenciodinâmica de duplo loop (DL-EPR). Para isso corpos de prova do aço em estudo foram solubilizados a 1175ºC e envelhecidos a 700ºC em tempos entre 10 min e 360 h. Corpos de prova metalográficos foram utilizados para caracterização microestrutural que foi realizada por meio de técnicas de estereologia quantitativa a partir de imagens de elétrons retroespalhados e análises magnéticas usando o ferritoscópio. Os ensaios DL-EPR foram conduzidos em solução 2M H2SO4 + 0,5M NaCl + 0,01M KSCN à 30ºC em amostras polidas. Observou-se que o comportamento eletroquímico do aço UNS S31803 possui forte influência da microestrutura, já que o grau de sensitização (GS) aumenta com o aumento do tempo de envelhecimento, devido à formação de fases intermetálicas que empobrecem as regiões adjacentes em Cr e Mo.

Aug 7, 2018