Search Documents

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Isabel Ferreira de Barros

O objetivo deste trabalho é avaliar o efeito da frequência de pulsação da corrente de soldagem sobre a microestrutura e propriedades resultantes de solda de chapas finas do aço inoxidável austenítico AISI 316L. Chapas do aço inoxidável AISI 316L foram submetidas à soldagem variando a frequência de pulsação de 2 a 8 Hz, mantendo-se constante a energia de soldagem. Os parâmetros de soldagem foram selecionados de forma a se obter penetração total. Foram realizadas análises das características superficiais. A microestrutura da seção transversal foi avaliada por microscopia óptica e microscopia eletrônica de varredura. A avaliação da resistência mecânica foi realizada por meio de ensaios de tração uniaxial, dureza e dobramento. Os resultados têm mostrado que variações na frequência de pulsação não atuaram de forma a conferir melhores propriedades mecânicas à junta soldada.

Aug 7, 2018

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017

By Bruno Cordeiro Costa

Inseridas em um mercado extremamente competitivo, as empresas siderúrgicas vêm buscando aprimorar seus processos produtivos e de gestão de forma a reduzir custos de produção e garantir sua sustentabilidade. A principal parcela do custo de produção da empresa em relação a um aço inoxidável ligado ao Cromo e Níquel está na Aciaria, e a carga metálica representa mais de 80% deste valor. Visando aumentar a competitividade, foi aberto um projeto para otimizar a carga metálica na Aciaria. A redução da mistura de escórias é uma fase deste projeto. O propósito do presente trabalho é mostrar a metodologia adotada para otimizar o processo de recuperação de sucata das escórias de aços inoxidáveis, minimizando a ocorrência de misturas de escórias, para maximizar seus teores de Ni e Cr e, consequentemente, reduzir o uso de fontes mais nobres e caras destes elementos. Foi adotada a filosofia “Zero de Escória no Chão” e, para alcançar este objetivo, várias ações foram implantadas. Considerando 2011 como base 100%, o teor médio de Ni da sucata recuperada de 3XX aumentou 45% em 2013 e o teor médio de Cr subiu 36% na sucata recuperada neste mesmo período. Como consequência direta da redução da mistura de escórias de grupos de aços diferentes ao longo de todo fluxo produtivo, ocorre a redução dos residuais de Ni e Cr nos aços carbono e elétricos e de Ni nos aços 4XX. A metodologia adotada foi eficiente e os objetivos do projeto foram alcançados.

Jul 30, 2018

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Georg Keintzel

The origin and elimination of 3rd octave mill chatter is a frequently investigated topic since tandem cold mills are in operation. So far only chatter monitoring systems have been successfully deployed, but this implies speed reductions and therefore a significant loss in mill output. Primetals Technologies has developed a new system using active injection of damping in order to eliminate 3rd octave mill chatter. The new hydraulics-based ChatterBlock® Control has now been proven successfully in mill operation. 3rd octave mill chatter, typically occurring in a frequency range between 90 and 150Hz, is a self-excited vibration phenomena typically occurring in the rear stands of tandem cold mills. It can produce significant gauge variations and even cause strip breaks. 3rd octave mill chatter is characterized by a quickly diverging vertical vibration of the rolls for specific rolling conditions (material, mill speed, forces, gauge etc.). Its occurrence requires immediate speed reduction of the mill in order to avoid strip breakage and/or strip quality degradation. This phenomenon thus severely limits mill productivity. The first step to proof the industrial feasibility of the new system was its installation on stand no. 4 of a 5-stand tandem mill. The development process and first results of the industrial implementation will be presented in this paper.

Aug 16, 2017

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Bernardo Siqueira

This paper presents a unique stirred milling technology, Outotec HIGmill™, a modern, flexible and energy efficient grinding solution for fine and ultra fine grinding being tested in an industrial scale level. The test was performed at an iron ore pellet producing plant in Sweden (for confidentiality reasons, it will be referred to only as “the client”) where a pilot HIGmill™ unit (HIG25) was installed parallel to a conventional regrind circuit to compare its performance to the existing ball mill. By using a continuous test run procedure and evaluating the parameters of F80, P80, mill shaft rotation speed and power drawn it was determined its grinding capabilities, operational flexibility and energy efficiency. Outotec HIGmill™ outperformed the existing ball mill in the plant proving its capabilities to grinding finer, with steeper particle size distribution (PSD) and much higher energy efficiency. The tests performed showed that, with further refining of its operation, it is capable of consistently deliver the required PSD with up to 30% higher grinding efficiency.

Aug 16, 2017

By Sandro Griza

Neste estudo, foi analisado um segmento de perfil em “U” que rompeu em serviço. O perfil compunha uma estrutura metálica em treliça que sustentava uma bandeja de construção civil. Foram realizadas análises de fratura, análises de caracterização do material e estudo de rigidez do perfil. O perfil rompeu por sobrecarga estática porque foi instalado do lado inverso. Isto desfavoreceu a rigidez da estrutura.

Aug 16, 2017

By Fabrício Tibúrcio Silva Araújo

O AutoLog é uma solução em tecnologia de automação e informação para controle absoluto do carregamento e descarregamento de caminhões em um grande cliente no ramo de fertilizantes. Seu objetivo é garantir uma operação autônoma que otimize os lucros e reduza os custos em logística. Este trabalho visa demonstrar o problema que originou a solução, a metodologia utilizada no seu desenvolvimento e o seu objetivo final.

Oct 30, 2017

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By Alexander Fleischanderl

Steel market has become somehow unpredictable and requires quick adjustment in production conditions to survive in the harsh market environment. Steel production is not anymore driven by output records, but by efficient cost reduction measures to remain competitive under strongly varying production conditions. Energy efficient production and flexible raw material scenarios have become decisive factors to succeed and survive in our industry. Such scenarios have to be carefully investigated to be well prepared to adopt production steps continuously. The paper analyses various process opportunities to optimize energy and raw material consumption in the production route. Off-gas treatment systems have still a huge untapped potential to recover energy from the hot waste gases. This is valid for the EAF mini mills as well as for the integrated route. Various examples for waste heat recovery systems including resulting benefits are discussed for the EAF, agglomeration, blast furnace, direct reduction and BOF. New innovative bag-filter systems feature extremely low emission levels at lowest pressure loss and sound emission conditions. Also improved control and automation solutions support the operators to minimize the operation and maintenance costs of their off-gas system. Steelmaking by-products shall not be considered as residues, but as a valuable and cheap raw material source. The paper presents some show cases how to valorize slags as well as utilizing coke and iron oxide fines to increase productivity and minimize raw material cost. A new process for highly flexible converter steelmaking allowing for extraordinary high HBI and scrap rates above 50% and improved yield is discussed and evaluated

Oct 30, 2017

By Claudio Pereira Diogo

A lot of galvalume/aluzinc steel sheet was furnished to a metallic roof manufacturer intended for tile fabrication. But, according with the roof manufacturer, that coils develops a different superficial aspect during processing. The purpose of this work was to provide an explanation for the appearance of the observed surface on one side of the coils. In order to find out the origin of the problem, mechanical and microstructural characterization tests were done at INSPEBRAS with the support of a partner laboratory. The results are described in this paper with their analysis and conclusions.

Aug 16, 2017

By Jean-Paul Simoes

The development of the blast furnace over the last years lead to a substantial increase in production capacity and productivity. This development triggered an evolution of the cooling systems in order to cope with the raising heat loads. The excellent protection of the shell by copper staves allowed blast furnace operators to achieve campaign lifetimes of more than 20 years. However in recent years some blast furnaces have experienced severe wear of the copper staves due to abrasion. The influences of the blast furnace design as well as of the operation conditions on this premature wear have been analysed and the mechanisms leading to the wear will be explained. New developments in the copper stave technology are part of the solution for avoiding premature wear during periods with less favourable conditions. The protection mechanisms made available by the new design extend the inherent protection mechanisms of copper staves to these periods. BFXpert® system is the ideal tool for the monitoring of the process data, the process models and the recommendations given by Sachem® support the operator in choosing efficient operation points. The charging with a Bell Less Top® (BLT) allows an accurate controlling of the blast furnace with regard to the optimization of the gas distribution. High performance operation together with long campaign lifetimes are thus made possible.

Aug 1, 2018

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017