Search Documents

By M. Potesser

One of the main targets in the automotive mass industry and supplying industry is the weight reduction of the vehicle for decrease of the fuel consumption. For that reason combinations of different kinds of materials and connections of, for example, steel and aluminium are developed or are already successfully field-tested. A determining factor concerning the quality assessment of the welded joint during hybrid welding is the characterization of the intermetallic Fe-Al layer regarding strength, hardness, morphology and mainly the different phases in which Fe occurs together with the Aluminum (FeAl, Fe2Al5, FeAl3.). A combination of conventional light microscopy, SEM - EDX - analysis, the usage of an atomic force microscope including a Nanoindenter and theoretical thermodynamic calculations turned out to be highly effective. Based on the attained results, the constitution of the intermetallic FeAl layer, influenced by silicon, manganese and zinc, can be predicted.

Jan 1, 2006

By Olga Karabelchtchikova

Keywords: Multipass grinding, Residual stress, Retained austenite, X-ray diffraction The study investigated residual stresses behaviors and their superposition effect in D2 dies for thread-rolling applications. A nested factorial experiment was applied to test hypotheses that the residual stresses profiles change due to combination of heat treatment and multipass grinding operations, and that certain patterns can be derived due to the memory relationship between pre-existing and final residual stresses distributions. The amount of the retained austenite along with residual stresses in variation with depth was measured using x-ray diffraction technique. Statistical analyses indicate that the proposed hypotheses hold. Residual stresses distributions as well as tensile peak location were found to be significantly influenced by the treatment parameters used. Unique characteristic patterns in the residual stresses profiles were observed due to multipass grinding technique across all experimental conditions. This finding suggested a plausible memory relationship between the cutting passes, and the causes of the foregoing results are further proposed and discussed.

Jan 1, 2005

By Z. Sun, H. A. Davies

"Current understanding of the mechanisms by which glassy and crystalline thin ribbons are formed in high speed continuous casting processes is considered. A computer model of the combined heat and momentum transfer during melt spinning has been developed. The influence of roll velocity and of heat transfer coefficient (between the melt and the roll) on the temperature and velocity distributions within the melt puddle is analysed and the thickness of the extracted ribbon computed. The relative importance of heat and momentum transfer under different conditions is assessed and differences between the casting of crystalline and amorphous strip highlighted.IntroductionHigh speed continuous casting of thin metallic ribbon and strip is currently of considerable interest both to metal processers and to those studying process mechanisms. The practical interest arises both from the potential economic benefits to be gained from a shorter and more energy-efficient production route and from the ability to obtain extended and uniform thin strip having a metastable microcrystalline or amorphous structure with enhanced or unique properties. The latter arise from the rapid solidification associated with the cooling of very thin sections of melt brought into intimate thermal contact with one or two rapidly moving heat sinks.The principal processes for casting thin strip include free jet, chill-block melt-spinning (GBMS) (1), melt drag (MD) (2), planar flow casting (PFG) (3) and twin-roll casting (TRG) (4). For the first three of these, all essentially variants of melt-spinning, melt flows through a nozzle onto the circumferential surface of a rapidly rotating roll, whereas for TRG the melt passes into the nip between two contra-rotating rolls. We shall be concerned in this paper with the single-roll melt spinning processes only. For these, a puddle is established where the melt contacts the roll surface and the length of this puddle l is a function of the process conditions, notably the circumferential velocity of the roll Us and the volumetric flow rate of the melt Q. The contact time between any point on the roll surface and this puddle, or residence time eR(= l /Us) determines the thickness of ribbon t extracted from the puddle. This thickness, in turn, partly governs the cooling rate T and the amount of undercooling in the melt and thus the microstructure of the solidified ribbon."

Jan 1, 1986

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By A. Gibson

Most methods for the treatment of scrap printed circuit boards do not reclaim the components in working order as the boards are either fed to a copper smelter, to recover the valuable elements, or, simply landfilled. This work reports the dissolution of the solder in fluoroboric acid containing Ti4+ ions which was particularly selective for solder, allowing the components to be recovered. The solder was subsequently electrowon from the leachant. The boards were then shredded and the copper dissolved in ammonium sulfate and, then treated via solvent extraction to give an electrolyte suitable for electrowinning. The remainder of the metals were dissolved aqua regia, silver remained unattacked by the aqua regia, palladium precipitated as Pd(NH4)Cl6 in the presence of zinc and nickel, the gold was removed by solvent extraction and precipitated as nanoparticles. The aqua regia was then diluted and the zinc and nickel separated by solvent extraction.

Jan 1, 2009

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By Pinai Mungsantisuk

Keywords: Pd-Ni alloys, Pd-Fe alloys, Pd-Co alloys, Magnetostriction, Magnetic Properties The presence of congruent melting minima, the occurrence of ferromagnetic transition over a large composition range, and FCC type crystal structure make Pd-Ni, Pd-Co, and Pd-Fe based systems attractive candidates in our search for materials with no rare-earths, large low-field magnetostriction, and good mechanical properties. The presence of paramagnetic-ferromagnetic transition over a broad range of composition also provides opportunity for fundamental studies. In this work, we have examined the magnetic and magnetostrictive behavior of Pd-Ni, Pd-Co, and Pd-Fe alloys over the entire composition range. Alloy sample rods were prepared by arc melting and casting. X-ray diffractometer was used to obtain lattice parameter data. Magnetostriction was measured along the rod axis using strain gages. Magnetic properties were measured using a vibrating sample magnetometer.

Jan 1, 2005

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005