Search Documents

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Paul K. Sims

The Central City district is one of several adjacent mining areas in the Front Range, Colorado, that contain precious metal-bearing sulfide veins of Laramide (Late Cretaceous and early Tertiary) age. The districts are in the Front Range segment of the Colorado mineral belt, and are characterized by porphyritic igneous rocks of intermediate composition that have intruded Precambrian crystalline rocks in the core of the Front Range. The veins and minor stockworks that constitute the ore deposits in the district were formed largely as fracture fillings. The veins range from simple fissures to complex, branching lodes, and commonly range from less than 0.5 to about 1 m in width. The principal values are in gold and silver. The common metallic minerals are pyrite, sphalerite, chalcopyrite, tennantite, and galena; minor minerals are enargite, pitchblende, and gold tellurides. Quartz, cryptocrystalline silica, carbonates, fluorite, and barite compose the gangue. The ore deposits have a well-defined concentric zonal arrangement. A core of pyrite veins (central zone) is surrounded by a peripheral zone of galena-sphalerite vein with gold and silver. An intermediate zone contains transitional veins that have minerals characteristic of both the central and peripheral zones. The minerals were deposited in three stages during a single period of mineralization: uranium; pyrite; base metals, gold and silver. The wall rocks were altered primarily during pyrite-stage mineralization. Sericite envelopes developed adjacent to fractures, and were succeeded outward by zones of argillized rock. The valuable ore minerals were deposited in ore shoots localized by several types of structural controls, principally vein intersections, the physical nature and structure of the wall rocks, and irregularities along the fractures themselves. During supergene alteration, gold was concentrated in the upper, oxidized parts of the veins, commonly to depths of 50 m. The precious metal-bearing sulfide ore deposits are closely associated in space and time with the Laramide porphyritic igneous rocks and are believed to have been derived from hydrothermal fluids related to the magmatic activity. The ore deposits have mesothermal aspects and apparently formed in the temperature range 200°-320°C.

Jan 1, 2013

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By M. P. Meehan

The purpose of this paper is to present the Anamax Instrumentation Department's: responsibilities, organization, preventive maintenance, test facilities, training and applications. The Anamax Mining Company is a general partnership between AMAX Arizona, Inc. (a subsidiary of AMAX INC.) and The Anaconda Company (a subsidiary of Atlantic Richfield). Anamax's product and by-products include: copper, molybdenum, and silver; uranium is to be added as a by-product in early 1980.

Jan 1, 1980

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By Y. Luo

Surface subsidence process due to underground coal mining often has the potential to cause problems to buried pipelines. In this paper, a technique for assessing the stress level on a subsidence-affected pipeline is introduced. The main contributors for the stresses on the pipelines are identified. Mitigation techniques for reducing the stress on the pipeline have been proposed and successfully tested.

Jan 1, 1997

By Fernando Pendás, Jorge Loredo, Alumudena Ordóñez

Water derived from mine-tailings typically contains high concentrations of H+, SO4, Fe and other metals, and it frequently suffers a decline in pH and the development of acidic mine drainage (AMD). A paper describing the results of a series of laboratory experiments with real AMD and a subsequent field trial with a in situ pilot system to assess a potential method for remediating tailings-derived water is presented here. After testing different organic substrates, residence times and flow conditions during two years to determine the most appropriate treatment for a polluted Spanish AMD, a pilot scale system combining SAPS, ALD, oxidation/sedimentation ponds and an anaerobic wetland was designed. Preliminary analyses of effluent samples indicate acidity and metal removal is occurring within the system, although sulphate removal is not complete. The results of this small-scale field trial suggest a potential cheap, long-term alternative for remediation of acid mine drainage.

Jan 1, 2000

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to benepciate a high- MgO siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for car- bonate removal and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth. The phosphate flotation stage produced concentrates analyzing about 31% P2O5 0.7% ? 5 MgO, and 4% insol. The overall P2O5 recovery In the two stages was about 85%

Jan 1, 1991

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By Charles M. Hauptman

The Karst asbestos deposit, discovered seventy years ago, is 32 miles south of Bozeman in southwestern Montana. The deposit is about one-half mile west of the Gallatin River which flows in a deep V-shaped valley flanked on either side by rugged mountains. The Madison range is west of the river and the Gallatin range lies to the east. A busy all-weather highway, U.S. No. 191, follows the river and is the major north-south route between Bozeman and the Gallatin valley to the north and Idaho and the west entrance of Yellowstone National Park to the south. The asbestos deposit is a large body of serpentinized peridotite in which anthophy11ite.occurs, both as distinct veins and as a disseminated mineral in the peridotite mass. The known exposures of the asbestos-bearing rock occur on a steen south slope at an "elevation of about 7000 feet, an elevation 'which is about 1200 feet above the Gallatin River. Over the years, a number of small companies have attempted to exploit the Karst asbestos deposit without continuing success. The present operator, Galaxy Mining Corporation, has attempted a systematic approach to the problem by utilizing geologic and engineering surveys to determine the economic and technical feasibility of a mine and plant to produce a finished asbestos pro-duct. The results of this work indicate a high probability of success for the project. However the company now faces that dilel1lJllB so common to the non-metallic mineral business; that is, whether to continue a research program of further mineralogical and technological studies in conjunction with detailed market surveys or to rely on the work done to date and embark on a pilot progril1n

Jan 1, 1971

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the results of a study on the optimum auxiliary fan location to control air recirculation in dead-end workings where diesel-powered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut and with the intake air quantities varied using different auxiliary fans to control air recirculation and diesel particulate matter (DPM).

Jul 1, 2023

By Paul Madsen, Bade Sozer, Thomas Hennings, Eileen Test

The Rondout Bypass Tunnel in New York has two access shafts. The upper sections of the shafts are lined with steel pipe to resist a substantial net internal water head . Initial design included a ¾-inch-thick cement mortar lining (CML) for all three components. Because of concerns with CML application on large-diameter pipes, the protective lining was redesigned for shotcrete application. This paper discusses the details of that design, mock-ups, and shotcrete application.

Jun 13, 2023

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975