Search Documents

This paper reviews the historical literature and the author's experience with regard to the effect that the selection of grinding ball size or sizes has on ball mill grinding efficiency. The conclusions presented provide guidelines for single and multi-size charging prac- tices in commercial milling operations.

Jan 1, 1998

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By S. A. Beeson, C. Poole

This paper describes the development of a novel selective flocculation technique for recovering phosphate values from ores containing silicate or carbonate gangue minerals. Data from initial flocculation response and reagent adsorption studies on component mineral suspensions and synthetic mixtures were used to assess the influence of various process parameters (e.g., reagent dosages, particle size, solids concentration, and conditioning regimes) on single-stage selective flocculation tests involving natural silicate and carbonate ores. In these tests a high degree of selectivity was achieved using low dosages of a low-molecular-weight cationic dispersant and a mid-range molecular weight cationic flocculant. Testwork was then extended to the evaluation of several floc recovery systems (sedimentation, hydrocyclones, and floc flotation) in a multi-stage process involving redispersion and reflocculation. Results from these tests clearly demonstrated the feasibility of producing marketable phosphate concentrates from both ore types.

Jan 1, 1999

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one billion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1992

By J. E. deMasi

Over the past 12 years, Exxon Coal U.S.A., Inc. has shipped over 150 million tons of coal from two mines, Rawhide and Caballo, located in the Gillette, Wyoming, area. These mines are operated by The Carter Mining Company, a division of Exxon Coal. Shipments have moved to more than 25 electric utility plants in the west, midwest, southwest, and south. The customer plants have represented a wide variety of configurations, sizes. design criteria, emission standards, and operations in different parts of the country. We have learned a great deal about the performance of Gillette area coals in utility power plants during this period. This paper covers some of the highlights of Exxon's experience with these coals in customer plants. I will focus specifically on things mining engineers may be able to do to make the product better for the customer's use.

Jan 1, 1989

By R. F. Korcak

There exists a wide array of industrial byproducts that produce beneficial responses in the soil/ plant environment. These materials range from clean-coal-technology residues produced during the generation of electric power (particularly those high in gypsum) to mineral fines produced by the aggregates industry (i.e., sand, gravel and crushed stone). A number of these materials are examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems are discussed.

Jan 1, 1997

By S. Donges, P. L. Dunstan, B. J. Huls

The commissioning of a distributed digital control system for the grinding circuit at Cuajone was completed by mid-August 1985. Development of a successful strategy, excellent operator acceptability, and the visual aspects offered by the display of the central console improved mill through- put significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the milk and classifiers to be operated at maximum capacity. This paper discusses the strategy development and the production restrictions encountered, and evaluates the overall performance of the digital control system.

Jan 1, 1988

By Mark Cadzow, Rodney Lamb

CARBAD is a recently developed Australian process for the recovery of gold and platinum group metals (PGM). The process relies on the selective agglomeration phenomena of the gold and PGM to capture the mineral in a carbon-hydrocarbon media. The precious minerals are then extracted from the loaded media by a solvent gold room process producing a relatively pure concentrate. The media is then reformed and recycled. The process development from batch test work to a 5 t/h commercial scale CARBAD plant is discussed. The operation and results of processing a variety of ore types at several alluvial and hardrock gold mines is examined. The operating and capital costs for the CARBAD process shows that it is significantly less than that the conventional CIP/CIL. The environmental safety of the process is a major feature where precious metal deposits are located within urban environments or within wilderness areas.

Jan 1, 1989

By R. W. Ballmer

Bingham Canyon lies in the heart of the Oquirrh Mountains, 25 miles southwest of Salt Lake City, Utah. In it is located the world's largest open-pit copper mine, owned and operated by the Utah Copper Division of Kennecott Copper Corporation. From the beginning of open pit mining operations in 1906 until 1963, the pit haulage, or materials transportation, was primarily by rail. In 1963, phase-in of a truck haulage system in the upper two-thirds of the pit was begun. The details of that conversion, its associated problems and the resulting pit operation have been covered in an earlier paper.1 The purpose of this paper is to discuss various factors for consideration in transportation system selection, and to discuss some of the alternatives considered prior to making the change from rail haulage to truck haulage for a portion of Bingham Canyon.

Jan 1, 1968

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By G. Wang

Industrial minerals processing has gained importance lately, not only due to its wide range of new and regular applications in processing different industrial minerals, but also due to the strict specs under which products are commercialized. Among the processes applied to industrial minerals, flotation is a leading technology. The laboratory study and commercial operation demonstrate that the sulfonated reagents are very effective collectors for industrial minerals. This paper compares synthetic petroleum sulfonate with fatty acid on iron reduction in glass sand processing and describes the effect of conditioning pH on iron reduction using synthetic petroleum sulfonate as collector, the effect of molecular weight of natural and synthetic petroleum sulfonates on their flotation performance and the enhancement made for certain products.

Jan 1, 2011

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

The U. S. Bureau of Mines, through a contract research program with Foster-Miller, Inc., has identified guidelines for the selection of the most effective water spray system and water flow rates for use on continuous mining machines. Specifically, these parameters were modified to obtain maximum dust control with regard to quartz dust exposure and more stringent respirable dust standards due to quartz. A novel water spray system, consisting of flat fan spray nozzles, mounted across the top of the mining machine, along with high flow, flat fan and higher pressure hollow cone nozzles mounted under the boom has been identified and tested. The anti-rollback/underboom spray system minimizes dust rollback while increasing dust knockdown by its unique positioning of spray manifolds and orientation of spray nozzles. Respirable dust suppression characteristics of the system acted in three ways: - by wetting the surface of the broken coal material to prevent dust from becoming airborne; - by controlling the airflow pattern at and near the face to minimize dust rollback to the operator Is control location; and - by dust knockdown, i.e., airborne capture, or scrubbing of airborne dust from the air. During underground trials, the anti-rollback/ underboom spray system reduced dust levels at the operator's position and in the immediate return by 55 and 15 pct, respectively, when compared to a conventional spray system. Quartz dust levels at the operator '8 position were essentially eliminated, while quartz dust levels in the immediate return were reduced by 57 pct. Applying the concepts of this technique throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable quartz dust, as well as allow coal mine operators to comply with the associated, more stringent, respirable dust standards.

Jan 1, 1987

By P. L. Dunn, G. T. Adel, E. B. Cruz

Automatic control of fine-coal cleaning circuits has traditionally been limited by a lack of adequate sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for the on-line determination of ash contents in fine-coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73[±] 4% ash over a range of from 65% to 90% ash. While the results are comparable, the video-based system costs only a fraction of what a nuclear-based analyzer costs. The sensor is now installed at the Middle Fork preparation plant, which is owned by Pittston Coal Co.

Jan 1, 1999

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By F. Milton Lewis

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling. smelting and hydro-metallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1977

By B. Denby, D. J. McMlarnon

During the ongoing research into the possible applications of Virtual Reality in underground operations, the AIMS Research Unit has developed a user-interface driven program which enables a user to input the geometry of underground mines, and add equipment and working processes in order to produce an accurate simulation of their operation. This paper describes the main features of this system (VR-MINE). Virtual Reality is a field which has grown out of three dimensional computer graphics techniques, and allows a user to move freely around a model held within the computer's memory. Movement around this model is carried out by the use of intuitive peripherals such as joysticks, with the user's view from their position within the model being produced in real time on a computer monitor or other device (such as a headset). This enables a user to interact with any three dimensional model and see the results of their actions immediately. VR-MINE is broken into two separate programs, both running under Microsoft Windows 3.1 or above. The first, the editor, allows the user to develop the mine layout and add equipment and personnel. The mine geometry is considered to be made up of various types of objects, for example a straight roadway segment which can be inclined, a junction roadway segment, and a turning segment. The geometry can then saved into a file to be loaded in by the second program of VR-MINE, the viewer. This generates a real- istic representation of the mine, with undulating floors and walls. It also has the ability to display multiple windows on the mine at the same time, which are arranged interactively. The simulation occurs within this program, with the user traversing the model in real time to examine possible areas of improvement in operations. This paper gives a number of examples of how the AIMS Re- search Unit has applied this technology to a range of underground mining scenarios to improve the safety of workers in the under- ground environment. The application discussed include computer graphics and Virtual Reality systems to training, risk analysis, visualisation, simulation, accident investigation and major hazard planning.

Jan 1, 1996

By J. Y. Kim

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In the present study, the flotation response of silver from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (Ag, CU)2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1990

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999