Search Documents

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By B. A. Kuyper

The Cove gold-silver deposit is located 50 km southwest of Battle Mountain, Nevada and 1.5 km northeast of the McCoy Mine. Total proven and probable reserves are 48.7 Mt (53.7 Mst) with an average grade of 1.85 g/t (0.054 oz/st) Au and 87.1 g/t (2.54 oz/st) Ag. Mineralization is hosted by Triassic carbonate and siliciclastic rocks in two separate orebodies. Oxide ore consists of disseminated gold and silver in clay-altered, manganese-flooded limestone. Sulfide ore is dominated by pyrite-sphalerite-galena veins in siliciclastic rocks and sandy dolomite. Gold and silver occur in the native state, associated with the base metal sulfides. Mineralization is interpreted to be the distal expression of a porphyry system. The McCoy gold (copper) deposit is interpreted to be the proximal expression of the same system.

Jan 1, 1991

By Alan R. Johnson

Because of the competitive nature of the iron ore pelletizing industry, commodities required for the production of pellets are continually being scrutinized to minimize their usage and offset rapidly escalating costs. In the Tilden pellet plant, the usage of one commodity, bentonite, has been reduced from over twenty-four pounds per long ton of pellets to as low as eight pounds per long ton. The evolution of bentonite usage from plant start-up to the present time is described.

Jan 1, 1984

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company's Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By Brian J. Gorva

The key objective of forming a cartel is to increase profits to members of the cartel by taking the following action: a) control output; and b) control price. However, while attempting to obtain monopoly profits the cartel members have to contend with costs associated with cartelization and such costs include the following: political costs; the cost of coordinating output and price; organizational costs (such as cheating); and administrative costs (such as the cost of attending cartel meetings). The objective of commodity exchanges is to provide an open, free market where buyers and sellers may openly complete transactions and pricing information can be immediately disseminated. These transactions include the following: a) to provide facilities for "hedging", or transferring price risk from buyers and sellers of physical commodities to "speculators" through the medium of buying and selling futures contracts, and b) taking physical delivery of metal on due dates.

Jan 1, 1983

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By J. J. Casey

This paper is one of a series of presentations organized by the Conference of American Society of Civil Engineers with the goal of making significant progress toward an equitable and effective allocation of risks in construction undertakings among the principal parties - owner, contractor and designer. The role I have been assigned is principally one of identification of risk while others will devote greater attention to the allocation of these risks and the contractual arrangements necessary to properly make these allocations. Construction projects are joint undertakings by parties who bring different skills and interests toward a common effort, much as this conference does. A project is not an adversary proceeding and does not benefit from establishment of an adversary mode, as our lawyer friends seek in the resolution of legal issues. Accordingly, I urge upon this Conference the adoption of two basic precepts and guidelines as the criteria for sharing of the risks inherent in construction undertakings toward achievement through mutual effort the common goal of a successful project completed in the shortest time and at the least overall cost. These precepts are: (1) that all risks are rightfully the owners unless transferred to or assumed by another party for a fair compensation; and (2) that the principle guideline in determining whether a risk should be so transferred should be whether the receiving party has both the competence to fairly assess the risk and the expertise necessary to control or minimize it. The sponsors of the conference have provided certain guidelines to the authors. There is, however, no constraint in expressing one's bias and I suspect that my contractor's outlook may be inherent in my comments. The guidelines have suggested that I indicate whether the risks identified are ones that can or should be shared or borne by one party alone. In doing so, I will attempt to follow the precepts I have recommended.

Jan 1, 1979

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

By H. Sevim

In a recently developed long term open pit production planning model, the optimum plan is found by exhaustively searching through nested pits of maximum-metal contents. A more efficient, dynamic programming (DP) based search algorithm now replaces the exhaustive search algorithm which was requiring prohibitively long execution time in real life cases. The logic and the formulation of the newly developed search algorithm are illustrated through a small hypothetical case. A real life gold deposit is treated to demonstrate that the algorithm does indeed find the optimum production plan among all possible plans. A comparison, in terms of computational savings between the two algorithms is also given.

Jan 1, 1994

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu's. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By R. R. Klimpel

The use of chemical reagents in flotation has been studied in great detail, e.g. (1, 2, 3, 4). Important progress has been made on the understanding of surface chemistry concepts involved in flotation. However, such scientific studies are often very complex even for rather simple idealized systems. Therefore, the deve- lopment of predictive or quantitative tools for plant engineering evaluation is still in the evolutionary stages. Until further progress in fundamental work is achieved, the operating engineer is faced with semi-empirical physical testing of reagent changes on several sizes of the actual equipment under study to be confident of the economic viability of any change.

Jan 1, 1980

By M. S. Safarzadeh

Cu-As feedstocks are among the most problematic copper sources that have been avoided over the past years. The high arsenic content of such ores/concentrates combined with their refractory nature have directed the metallurgical industry towards developing efficient technologies for the treatment of high-arsenic copper ores/concentrates. As the most important member of Cu-As-S mineral system, enargite (Cu3AsS4) is frequently encountered in some of the important copper deposits. Several hydrometallurgical and pyrometallurgical processes have been examined for the treatment of enargite concentrates, but currently, no commercial operation exists. In an effort to develop an original processing option, an acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2?4H2O, PbSO4 and Cu0.47Fe0.53SO4?H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 h with a sulfuric acid to concentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena, and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different levels. The purpose of this paper is to evaluate phase transformations during the acid bake-leach process for the treatment of an enargite concentrate, and to study the effect of sulfuric acid dosage on the extraction of Cu, Fe, and As. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.

Feb 23, 2014

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By G. H. K. Schenck

Weather changes of a daily, weekly, or seasonal period affect mineral production and cause significant losses that are considered unavoidable. Private weather forecasting services are available on a contract basis that can significantly reduce the uncertainty associated with weather-induced changes in the production of and demand for minerals. This paper provides examples of current practice and reviews the opportunities that await those producers who incorporate weather services as an integral part of their operating, scheduling, and planning procedures. Private weather forecasts can be highly accurate because atmospheric trends such as conditions and movement tend to persist and are related to previous meteorological events. Commercial meteorological services are prepared to deal specifically with a mineral producer&apos;s special problems (Table 1). Tactical use of private forecasts is a major advance over the severely restricted value of public forecasts which, of necessity, are general in nature and cover a dispersed geographic territory. Private weather services provided on a consulting fee basis offer the mineral producer the opportunity for tactical and strategic response to weather conditions at an acceptable cost. This contrasts with the too-frequent current tendency to view weather as a random variable the costs of which are unknown and about which nothing can be done.

Jan 1, 1970

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994

By G. S. S. Raman, M. S. Klima

The effects of pressure and cake thickness were studied using a split-plot design for pressure filtration of a fine refuse slurry obtained from a bituminous coal preparation facility. Pressure filtration offers the potential to significantly reduce the moisture content of the fine refuse stream with the addition of little to no flocculants, thereby minimizing the volume of refuse stored in impoundments and providing a recycle water stream for use within the plant. Experimental results showed that the final cake moisture decreased with increase in pressure and decrease in cake thickness. In addition, specific cake resistances calculated for the various tests indicated an increasing trend with increasing pressure and decreasing cake thickness. With increase in cake thickness, an increase in cake moisture and the weight of solids deposited in the cake was observed. An ANOVA analysis indicated that both cake thickness and pressure significantly affected the cake moisture, while only cake thickness statistically influenced the weight of solids in the cake. A regression model was developed with an R2 value of about 0.99 to relate cake thickness, the single largest statistically significant factor, with the weight of solids in the cake. Filter capacities were calculated in terms of the solids deposited per unit time based on a product specification of 25 percent cake moisture, and it was observed that the thinnest cake had the highest filter capacity.

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019