Search Documents

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By F. W. Mueller

It seems to be a matter of general understnading that title extraction or use of ground water may not be used as the basis of a depletion deduction under the United States Revenue Code And indeed, I have been unable to find any precedent upon which to base such a deduction. It is for this reason that the Shurbet case, which is the subject of my discussion and is now before the Court, may well become a precedent as authority for the allowance or disallowance of a depletion deduction for income purposes. It is well known that the law recognized that capital is consumed in the process of extracting minerals, oil and has, other natural deposits, and timber (underscoring supplied). This exhaustion, or depletion, is likened to the using up of raw materials in manufacturing. The law, therefore, provides a deduction for depletion which is intended as compensation for the exhaustion of assets consumed in the production of income through severance of minerals, oil and gas, other natural deposits, and timber.

Jan 1, 1962

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022

By Jr. Schnakenberg

The automation (robotization) of coal mining activities at the face offers improvements in worker safety and productivity. The evolutionary introduction of autonomous, intelligent robotic machines to perform the most hazardous tasks may become a reality within the next 10 years. The U.S. Bureau of Mines Robotics and Automation research program is aggressively pursuing the development of the enabling technology necessary to achieve this goal. This program consists of both core and applications research, each focused on the fundamental issues of robotic technology. In the short term, the research is directed specifically to the robotization of present-day underground equipment and is being performed in a manner that can make incremental improvements in safety and productivity. The long-term goal is the development of intelligent autonomous mining systems.

Jan 1, 1990

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By Bert C. Morrison

In 1961. American Smelting and Refining Company was conducting exploration for lead in southeastern Missouri using several geophysical methods. Electrical methods were used in almost every hole drilled during this period. These methods met with only limited success, with one exception. This paper deals with that exception: An Electrical Potential Method used at a single hole to indicate direction to better mineralization. This method was notably successful in the program.

Jan 1, 1970

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By W. Rocher

The Minera Ojos Del Salado (?MINOSAL?) concentrator is located 20 kilometers southeast of Copiapo, Chile and processes copper ore provided by its Santos and Resguardo mines at a capacity of 4,200 tip (4,620 stpd). Phelps Dodge acquired the majority interest in MINOSAL in 1982. The principal incentive for this purchase was the exploration potential of the property. At that time, the concentrator plant was a small, antiquated installation with a capacity of 674 t/d (740 stpd). In 1982, the majority of the ore was produced from the Santos and Resguardo mines, but custom ores of copper, silver, and gold were also treated. The acquisition occurred at a crucial time in the copper business, since the price had fallen to nearly $0.50 per pound. In 1985, Phelps Dodge purchased the outstanding interest in MINOSAL and acquired 100% of the property. Today, after numerous improvements and two expansion projects, the concentrator is an interesting combination of old and new equipment. The regrind mills, for example, have been in service for about 50 years, while the ceramic concentrate filter represents the latest technology.

Jan 1, 1993

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By Rafael C. Castro, Paul V. Savard, Kathleen M. Murtagh

Preliminary design is underway for the Massachusetts Water Resources Authority’s (MWRA) next major tunnel program, the Metropolitan Water Tunnel Program (MWTP). The MWTP is the latest part of MWRA’s ongoing efforts to achieve redundancy for its metropolitan water transmission system including its historic deep rock City Tunnel, City Tunnel Extension and Dorchester Tunnels. The MWTP comprises several deep rock tunnels that will be approximately 10-foot to 12-foot finished diameter totaling just over fourteen miles long and ten connections to existing large diameter surface piping and pumping stations. This paper will present an update on current engineering and permitting efforts, packaging schemes, and the schedule to complete the MWTP.

Jun 13, 2023