Search Documents

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute&apos;s H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company&apos;s Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

By John B. Gustavson

The mineral deposits found in carbonate facies rocks of sedimentary basins include deposits comprised of the country rock itself such as limestone for chemical uses, dolomite for road aggregate, and a variety of other industrial uses of the sedimentary rock. Exploration for new reserves is generally conducted on basis of outcrop investigation, subsurface drilling, and facies change studies while geophysics and geochemistry are not applied. In contrast, rapid development has taken place in the application of both geophysical and geochemical techniques in exploration for stratiform deposits of zinc, lead, barite, and fluorite deposits. This paper will present case histories and show illustrations from such work in the Mid-Continent region. The Metals Division of International Oil & Gas, Inc. has gathered this experience through work over the last three years along the southern margin of the Eastern Interior platform focusing on the states of Arkansas and Tennessee. The exploration work was conducted partially for the Company&apos;s own account, partially in joint exploration ventures with mining companies including International Mogul Mines, Ltd., a Canadian company; Bear Creek Mining Company, a subsidiary of Kennecott Copper Corporation; the Mining Division of W. R. Grace and Company, and Boliden-Preussag Exploration, a Swedish-German partnership. We wish to take this opportunity to thank our venture partners for allowing presentation of the various sections of this paper.

Jan 1, 1976

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By J. F. Peterman, M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand fir the material as well as accurate projections of costs and prices. This paper develops a general method of predicting mineral requirements and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can he projected to establish future requirements. This forecast is critical to the evaluation of a new source of supply, such as the graphite resources of Upper Michigan.

Jan 1, 1990

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study adsorption of sulfide collectors such as modified thionocarbamates and thioureas, xanthate, dithiophosphate, and dithiophosphinate, on galena, chalcocite, chalcopyrite, and quartz under flotation related conditions. In the case of the adsorption of modified thiourea on chalcopyrite, chalcocite and Cu-activated quartz, and of dithiophosphinate on galena, SIMS measurements have provided direct evidence for the presence of metal-collector (1:1) complexes on surfaces. In the other systems, only the collector molecular ion and its fragments were detected. The distribution of adsorbed species on the surfaces was obtained by using SIMS in the imaging mode. On chalcopyrite, only the copper-collector complex was found; there was no evidence for iron-collector complex. In the case of quartz, adsorption of selective collectors was observed only after activation by copper ions.

Jan 1, 1996

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida&apos;s sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants&apos; and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By E. Sabina Brady

Over the next two decades there will be significant trade and development opportunities in China for mining, engineering, equipment, and construction companies interested in becoming part of the development of China&apos;s chemical and fertilizer industries. At last count, China&apos;s phosphate ore reserves of 11.8 Gt (13 billion st), ranked fourth in the world behind the US, the USSR, and Sahara-Morocco. However, a recent statement by the head of the Ministry of Geology and Minerals, Sun Daguang, claims that with increased prospecting in the last few years, China&apos;s phosphate reserves now rank first in the world. Whatever the actual size of its known and potential reserves, China&apos;s present phosphate processing capabilities fall far short of demand, while the substantial progress that has been made in this area points out the severity of the problems that still remain. Since 1949 China has developed 181 mines and increased its phosphate concentrate production from 10 kt (11,000 st) to 10.86 Mt (11.97 million st). By the 1980s, China was the third largest chemical fertilizer producer in the world-although this claim is slightly misleading as China&apos;s nitrogen/phosphate potassium ratios are far from average world ratios and even further from US standards. According to the Sixth Five Year Plan promulgated in 1982, the country&apos;s development plans emphasize the expansion and upgrading of key energy and industrial sectors, including that of fertilizer production-specifically phosphate and potash. Within the framework of the plan, the Ministry of Chemical Industry&apos;s development priorities are to: • Increase potash production by 150% to 50 kt (55,115 st). • Raise phosphate fertilizer production 21.2% to 2.8 Mt (3.1 million st), 46 kt (50,705 st) of which will come from new projects constructed and completed within the Sixth Five Year Plan, with projected new production of phosphate concentrate and complex fertilizer in the next decades totaling 500 kt (551,146 st). • Commence work to increase phosphate ore production by 8.33 Mt (9.18 million st). Facilities for 2.43 Mt (2.68 million st) will be completed and come on stream by 1985. • Commence work to increase iron pyrite ore production by 3.69 Mt (4.07 million st), facilities for 2.9 Mt (3.2 million st) will be completed and come on stream by 1985. • Verify 600 Mt (661 million st) of new phosphate ore reserves. Since the promulgation of the Sixth Five Year Plan, Chinese authorities have announced that 70 key construction projects will receive top priority in the implementation of the plan. These projects include five in the chemical industry area, including the construction of four fertilizer plants in Urumqi (Xinjiang), Zhenhai (Zhejiang), Beijing, and Lucheng (Shanxi), and a pyrite mine in Yunfu (Guangdong). In addition, by 1985 the state will expand or construct three major phosphate mines: Wangji in Hubei, Kaiyang in Guizhou, and Kunyang in Yunnan. Fertilizer Ratios In 1982, China&apos;s fertilizer production was slightly higher than 12 Mt (13.2 million st) and consisted of 80% nitrogen, 19% phosphate, and 0.19% potassium. By 1985, state officials project that fertilizer production will reach 13.4 Mt (14.8 million st) and consist of 78.4% nitrogen (10.5 Mt or 11.6 million st), 21.2% phosphate (2.8 Mt or 3 million st), and 0.39% potassium (52.3 kt or 57,605 st). To attain the world average using the country&apos;s 1985 projected production level for nitrogen, China will have to double its 1985 phosphate production to 5.76 Mt (6.35 million st) and increase its 1985 potassium production almost 80 times to 4.1 Mt (4.5 million st). These numbers demonstrate the seriousness of the fertilizer production problem in China today and the long-term nature of the problem&apos;s solution. Development Examples Yunnan is the third largest phosphate-rich province in China with verified deposits of 1.9 Gt (2.1 billion st). Despite this abundance, the province only mines around 3 Mt (3.3 million st) of phosphate rock annually. In June of this year, Yunnan announced its intention to initiate 39 development projects within the next two and a half years, requiring an estimated $200 million worth of foreign investment. The three areas receiving the most emphasis will be:

Jan 9, 1983

By L. D. Patts, S. J. Janisko, E. G. Cauda, A. D. Bugarski, G. H. Schnakenberg, J. A. Hummer

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on the performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for DFEs when the engine was operated at high-load modes rather than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on the total concentration of nitrogen oxides (NOX) were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes..

Jan 1, 2011

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977