Search Documents

By M. J. Hrebar

In the summer of 1990, a study was conducted to document large tractor (i.e., Caterpillar Dl1N) utilization in surface coal mining. The tractors were found to be utilized as primary production machines and in combination systems with blast casting and draglines and blast casting and excavator/truck systems. In addition, dozers were used to prebench ahead of a primary dragline system. The study also established ranges and averages for Dl1N operating costs and mechanical availability. Based on simulated production of various tractor dozing applications, the potential for low cost coal stripping was suggested (Hrebar, 1991). A follow-up study, also funded by Caterpillar Inc., was conducted in the summer of 1991 to determine actual production rates in two dozer stripping applications. These actual production rates would then serve as a foundation for estimates of stripping costs. This paper presents the results of the studies in a contour and a cast application.

Jan 1, 1992

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By R. Owen

The vision-based approach to process control involving fine particles in harsh on-line environments is discussed in this paper. The sensor equipment at the process location, consisting of a light source and a CCD camera provides RS-170 B&W video output. The video can be seen on a process monitor in the control room and is sent to a computer based Vision Processor. The Vision Processor contains a video digitizer and Canty developed software that extracts process information. The iron mine application controls thickener agent feed rate and thus settling pond overflow clarity. The sensor is mounted in the overflow flume of the outdoor settling pond and is used year around in the Minnesota weather. Alternate control system needs a low flow water sample which is subject to freezing in winter. The computer based vision processor provides 4-20 mA analog outputs for real time control as well as file archive for a history record.

Jan 1, 2001

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company's open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By G. W. Heunisch

G.A. Carmody and L.B. Anderson We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 9, 1987

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By James J. Scott

I am indeed honored to be the 1991 recipient of the Daniel C. Jackling Award. To be voted this honor by my peers in the Society for Mining, Metallurgy, and Exploration and AIME means more to me than I can truly express. Daniel Jackling's position and prominence in the mining industry first came to my attention in the fall of 1949 when I transferred from Wisconsin Institute of Technology, then a three-year school, to the Missouri School of Mines to complete my last year for a bachelor's degree in mining engineering. I played basketball in the Jackling gym and ran track on the Jackling field. I didn't know a lot about Jackling then, except he was an honored graduate of the school and, obviously, supported the school financially. Over the years, Jackling's name kept coming up. He was a man with a reputation for being a doer, a mining leader who was always a step ahead, a mining engineer who knew how to motivate men in the working place, to organize mining systems, to finance and organize corporations. to open up new, low-grade ore bodies for exploitation. If Jackling were alive today, I would expect he would bean excellent candidate to apply practical rock mechanics to his projects. Looking over the list of Jackling Award recipients, I have known many, have met many personally and had a few who were dear friends that affected my own professional life. Ab Shoemaker, '58, and I consulted at the White Pine Copper Co. on mining problems in the 1960s. We arranged for our visits to the mine to coincide so that we could collaborate on our ideas. I would rent an auto and drive for Ab. He said he was the only mining engineer in the country that had a PhD for a chauffeur. James Boyd, '67, was my mentor as regards the White Pine Rock Mechanics Program that we organized in 1963. Only through Boyd's forsight. leadership, dedication and willingness to spend money on research and development did the Practical Rock Mechnics Program at White Pine succeed. He never wavered in his support to that program or to me personally. Tom Howard, '75, was my predecessor in 1970 as Director of Mining Research for the US Bureau of Mines. When I joined the Bureau in August 1970, he had the research centers up and running. Any successes I may have had with the Bureau of Mines were due in great part to Tom's leadership and organization throughout the 1960s. Gene Cameron, '68, was my teacher at the University of Wisconsin and I remember him fondly. He was the one professor who lectured in a manner that made me welcome going to his classes each day, a truly remarkable educator. If you have come today to listen to me talk about instrumentation, rock properties, stress-strain relationships, rock mechanics theory, etc., you will be disappointed. Large volumes of data have been collected by well qualified theoreticians to define stress-strain conditions in mines. Unfortunately, very little of this data has been used by industry due to the lack of initiative and understanding by the researchers to the true problems of implementation in the industry. I hope my remarks will assist future investigators to work through the maze of operational problems so they will experience the satisfaction of seeing their research used. I fully realize that the Jackling Award is given by the Society for Mining, Metallurgy, and Exploration and is primarily offered for accomplishments in hardrock mining. I have found it impossible to separate hardrock and coal mining when I talk about "Applied Rock Mechanics." There is too much overlap and the same mechanics principles are applied to both. For example, coal mine designs have been applied to salt, trona and potash. Also, the original layout and design of White Pine Copper Mine was based on coal mine designs. Any developments to apply rock mechanics ideas must

Jan 1, 1992

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970's. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometry of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers, and management and will help mine operators plan the optimum mining sequence for different mine geometries and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2001

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016