Search Documents

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By F. D. Everett

This report summarizes the results of a nationwide investigation completed in 1964 to determine the nonferrous base metal ore reserves and potential sources of ore and to evaluate criteria for their ultimate exploitation. Engineers of the Bureau of Mines contacted mining company officials, reviewed reports and Government records, and where necessary made personal appraisals in arriving at the results. The estimates are presented by metals in ores in geographic regions and include some of the problems affecting the reserves and potential sources. The recoverable metal in the measured ore category and in the total ore reserves was estimated as follows: [ ] At the 1963 rate of domestic mine production these total reserves would be adequate to provide copper for 62 years, lead for 121 years, and zinc for 42 years. Data also are given for gold, silver, and other coproducts. Reserve estimates greatly exceed those of previous investigations; some prior estimates of copper reserves are included for comparison (table 23). Projections of requirements for base metals indicated the United States will need approximately 45 percent more copper in 1970 and 110 percent more by 1980 than was consumed in 1960; similar projections for lead indicate increases of 20 percent by 1970 and 45 percent by 1980; zinc projections are 40 percent more by 1970 and 90 percent by 1980. Much of the production of gold and silver is a coproduct of base metals recovery and the projected need for the precious metals exceeds all the United States can produce. Some problems of the industry are mentioned. A graphic evaluation of the economic availability of the reserve and potential sources is shown.

Jan 1, 1967

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

This Bureau of Mines report describes research on methods of assuring the continued safety of mine electrical power distribution circuits through reliability and quality assessment of the protective devices, innovative inspection techniques for these devices and the circuits themselves, novel applications of trolley line circuit breakers, and computer modeling of distribution systems to determine the proper ratings for cables, power sources, and circuit protective elements. Battery charger safety is included.

Jan 1, 1979

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock-dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. nonmetallic mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and sand and gravel mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the cool mining sector.

Jan 1, 1988

By Neldon L. Jensen

Although ASARCO Incorporated, the only domestic producer, had terminated copper smelting operations and associated recovery of byproduct arsenic trioxide at Tacoma, WA, in 1985, it shipped small quantities of both trioxide and metal from its remaining stocks in 1986. Imports for consumption of arsenic trioxide increased significantly, owing to increased demand for arsenical wood preservatives and the decrease in domestic shipments of trioxide. Prices remained unchanged throughout the year. Development of gallium arsenide integrated circuits, important in advanced military and commercial electronics circuitry, continued to gain momentum during 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide and metal from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1988

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By George S. Rice

The following paper was presented at an International Conference on Mine Safety Research held at Dortmund, Germany, September 23-28, 1935, inclusive. This conference was attended by representatives of Belgium, France, Germany, Great Britain, and the United States ands by invitation, Czechoslovakia, Poland, Spain, and Russia. The first international conference of representatives of mine-safety, research stations was held the United States Bureau of Mines Pittsburgh Experiment station in 1912 .4/

Jan 1, 1936