Search Documents

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 2010

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By Steven A. Fechner

In 1984 the Bureau of Mines cunducted mineral investigations of specific sites within the Yentna Mining District. One hundred eight placer and rock samples were taken. Reconnaissance placer samples were collected from drainages in the Talkeetna, Susitna, and Yentna River basins. The highest placer gold values were found in the historic placer gold producing creeks of the Cache-Peters Creek area. Samples taken from an outcrop in the Middle Fork of Iron Creek in the Talkeetna Mountains contained previously unreported high lead, zinc, and silver values.

Jan 1, 2011

By Floyd D. Everett

The J. B. fluorite deposit is in the Washington mining district, southwestern Beaver County, Utah (fig. 1). Fluorite outcrops were found during 1942, and three lode claims wore located. Little work was done on the property until October 1943, at which time the Bureau of Mines started development to determine the subsurface extent of the fluorite mineralization exposed at the surface. The most prominent rocks in the J. B. mine area are porphyries, which vary considerably in composition. Dacite porphyry appears to be the most common host rock for the fluorite-quartz-calcite lenticular masses. The dacite porphyry in the area is highly brecciated over a strike length of more than 1 mile. Fluorite deposits in the brecciated zone cover a strike length of approximately 400 foot. The fluorite lenses range in length from 40 to 200 feet and in width from 4 to 10 feet (fig. 2). The Bureau of Mines work on the J. B. property was started in October 1943 and completed in October a year later. The work consisted of surface trenching by bulldozer and hand methods, shaft sinking, drifting, and crosscutting. Eleven trenches totaling 1,800 linear feet were excavated. An inclined shaft was sunk to a depth of 105 feet, and from thin shaft 577 feet of drifts and crosscuts were driven to outline the extent of the mineral deposit (fig. 3). Two hundred ninety-seven samples were taken in the surface trenches and underground workings. The locations of the samples and analyses arc shown in accompanying figures and tables. Results of metallurgical tests comprise the concluding section of this report.

Jan 1, 1950

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By R. S. Dean

A general survey of the metallurgical work of the U. S. Bureau of Mines has been given in an article in the Missouri School of Mines Alumnus, and a somewhat more detailed review of the bureau work on lead and zinc will be found in the Mining Congress Journal. C. C. Furnas has contributed one general mathematical article. Dean, R. S. U. S. Bureau of Mines. 4, 1930, pp. 7-8. Program of Metallurgical Investigations of the Missouri School of Mines Alumnus, vol. 4, No. Investigations of the U. S. Bureau of Mines on the Milling and Smelting of Lead and Zinc. Min. Cong. Jour., vol. 16, 1930, p. 799, 808. Furnas, C. c. Evaluation of the Modified Bessel Function of Am. Mathematical Monthly, vol. 37, the First Kind and Zeroth Order. No. 6, 1930, pp. 282-287.

Apr 1, 1931

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3 leach, HNO3 ?NO2 leach, H3 ?CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast , and ammonium salt roast .

Jan 1, 1963

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By T. F. Mitchell

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and obtained samples of ore from two properties in the vicinity of Bettie Mountain, Lander County, Nev. In addition, samples from three claims in the Carico Lake region, Lander County, Nev., were submitted by private interests. RS the ores were too low in grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore dressing was investigated. The Black Bock property is 16 miles south of Valmy, Nev., and is owned by Western Alloys, Inc., Salt Lake City, Utah. The deposit is a replacement of sedimentary rock by manganese oxides. Ore occurs in two main ore bodies designated as the "upper bench" and "lower bench", which could be mined separately. Examining engineers obtained samples from each ore body, and laboratory experiments were made on each sample. The Black Eagle group of claims is in Lander County, Nov., about 43 miles southwest of Battle Mountain. Ore occurs as a replacement of manganese oxides in shale and chert. The 2-ton sample of ore used for laboratory testing was taken by a Bureau of Mines examining engineer from an adit that partly transversed a 28-foot bed of ore. The property is controlled by Western Alloys, Inc.

Jan 1, 1951

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By R. D. Leitch, C. A. Taylor

Trinitrotoluene is made by the direct nitration of toluene by a mixture of nitric and sulphuric acids . The exact procedure varies , but the product , where Grade I of TNT is desired , is similar , and consists largely of material that has a melting and setting point of 80.6 °c . The purification consists of draining off the liquid portions , including the acid and liquid nitro compounds . The mass is crushed and washed until the TNT is acid - free . It may still have a low-melting point due to the presence of material of lower nitration. Other isomers also have the same effect . The crystal mass may be washed with a solution of sodium sulphite , thiosulphate , sulphuric acid , or with an organic solvent such as alcohol , benzene , or carbon tetrachloride , Where a very pure product is desired , the TNT is separated by fractional crystallization from solution in organic solvents . The TNT is If it forms In some cases the material is melted during purification . agitated as it cools to prevent solidification in a solid mass . in a solid mass , this is broken up and screened . There has been some question as to the effect of the different methods of purification on the strength and sensitiveness of TNT , although all methods left a product that would give satisfactory tests .

Sep 1, 1923

By C. Gary Reiness

A safety glass eyepiece which had been repeatedly exposed to mine environment over a number of years was studied to determine some of its optical properties. In the regions from 385 to 400 mµ and from 625 to 760 mµ, the transmittance was less than the 89 percent required by the American Standard Safety Code for Head, Eye, and Respiratory Protection. From 200 to 320 mµ the relative transmittance of two parts of the eyepiece was found to vary widely, having a maximum of 38 percent difference at 315 mµ. Irradiation of the glass by ultraviolet light caused enhanced absorption in the range from 200 to 1,200 mµ. There was a time-dependent increase of 1016 color centers per cubic centimeter throughout this range after 36.5 hours of irradiation. The rate-of-growth curve for the optical density, at 243.5 mµ and 23° C, was resolved into linear and saturable components, indicating zero order and first order

Jan 1, 1968