Search Documents

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By Albert E. Long

Since December 10, 1945, the Mount Weather Branch, Mining Division, Bureau of Mines, has been maintaining detailed performance and cost records on the diamond coring bits used throughout the United States by the Bureau of Mince. Figure 1 is a copy of a typical master record sheet showing the scope and type of information recorded for each bit. It is the intention of the Bureau of Mines to issue analytical reports covering the effects of diamond size and quality on the cost of core drilling in different rocks as the information on a significant number of bits used in any one type of rock is accumulated. This report is the first of such a proposed series and is based on the diamond loss and bit costs incurred in the use of 539 AX bits in coring operations on 10 different projects involving 6,097 feet of drilling in gneiss. The 10 projects were located in New York, Pennsylvania, and New Jersey (fig. 2). As a result of the information accumulated on the use of diamond-coring bits in drilling in gneiss, it has been found that the type of bit, the matrix, the percent of core recovered, and the size and quality of diamonds used have a definite effect on the cost of bits per foot drilled.

Jan 1, 1950

By E. C. Perkins

The purpose of the research described in this report was to develop techniques for using ilmenite from domestic deposits for the production of titanium tetrachloride. The research was done by the Federal Bureau of Mines in cooperation with the General Services Administration under contract DMP-116, Utilization of Domestic Ilmenite. Bench-scale continuous chlorination of an Idaho ilmenite containing 27.9 percent titanium and 35.6 percent iron yielded a crude titanium tetrachloride suitable for purification and for the production of titanium metal and pigment. A summary of the results of 380 hours of operation showed that 82.4 percent of the titanium was chlorinated, with 92.5 percent utilization of chlorine. The construction- of a. quartz tube chlorinator 4-inches in diameter and 24 inches long is described with the necessary details of operation.

Jan 1, 1961

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By X. C. Shi

Bacterial mutagenicity and mammalian cell chromosomal and DNA damage in vitro assays were performed on a diesel exhaust particulate material (DPM) standard in two preparations: as an organic solvent extract, and as an aqueous dispersion in a simulated pulmonary surfactant. U.S. National Institute for Standards and Technology DPM SRM 2975 expressed mutagenic activity in the Salmonella reversion assay, and for in vitro genotoxicity to mammalian cells as micronucleus induction and as DNA damage in both preparations: as an acetone extract of the DPM mixed into dimethylsulfoxide, and as a mixture of whole DPM in a dispersion of dipalmitoyl phosphatidyl choline. Dispersion in surfactant was used to model the conditioning of DPM depositing on the deep respiratory airways of the lung. DPM solid residue after acetone extraction was inactive when assayed as a surfactant dispersion in the micronucleus induction assay, as was surfactant dispersion of a respirable particulate carbon black. In general, a given mass of the DPM in surfactant dispersion expressed greater activity than the solvent extract of an equal mass of DPM.

Jan 1, 2009

By W. W. Weller

Low-temperature heat capacities of scandium sesquioxide (Sc203) and a mixture of cerium sesquioxide (Ce203) and cerium dioxide (CeO2) were measured over the temperature range from 50° to 298° K. The entropy of scandium sesquioxide at 298.15° K was evaluated directly as S°298.15 = 18.4 ± 0.1 cal/deg mole. That of cerium sesquioxide was extracted by combining the heat-capacity data for the mixture with those for pure cerium dioxide; the result was S298.15 36.0 ± 1.0 cal/deg mole.

Jan 1, 1963

By Paul L. Russell

Because of the increasing demand for fluorspar , investigation of the deposits of the Gila district in Grant County , New Mexico , was undertaken by the Bureau of Mines in 1943 with the cooperation of the Federal Geological Survey . It was the purpose of the investigation to assist owners and lessees to develop their properties and to attempt to estimate ore reserves that might be available to supply a 300- ton mill that was under construction at Gila . Field work was begun June 14 , 1943 , and ceased August 16 , 1943. Seven veins were trenched and sampled .

Feb 1, 1947

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By H. C. Young

This paper deals with roof bolting in Alabama coal mines and iron-ore mines from the time it was introduced in early May 1948 to May 1, 1953, a 5-year period. The Tennessee Coal & Iron Division of the United States Steel Corp. began systematic roof bolting in early May 1948 in a coal mine and in an iron-ore mine, which had some of the poorest roof conditions in the Alabama mines. After the efficiency of roof bolting had been proved by the Tennessee Co. it was gradually adopted by other companies throughout the State, until in May 1953 approximately 53 percent of Alabama's total coal production and 100 percent of Alabama's total iron-ore production, mined underground, was being produced from roof-bolted areas. Statistics in this report will show the advancement made in roof bolting in the 5 years and also the amount of roof bolting that was being done as of May 1, 1953. Significant progress has been made in the coal and iron-ore mines of Alabama in reducing the roof-fall fatality rates during the past several years by adopting systematic roof bolting. The groundwork was laid through successful experiments early in 1948 by the Tennessee Coal & Iron Division of the United States Steel Corp. in cooperation with the Federal Bureau of Mines. This experimental work was based upon the previous experience of the St. Joseph Lead Co.2/ in its Southeastern Missouri mines.

Jan 1, 1954

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953