Search Documents

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CPR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.

Jan 1, 1949

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 16 September to 1 November 1983. The testing covered herein is for coarse 2-in by a (minus 50 mm) Pittsburgh Seam coal in a 12-in (3 00 mm) pipeline, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s) and at concentrations ranging from 15 to 55 pct.

Jan 1, 1985

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By F. M. Goodwin, John Campbell, W. P. Yant, G. W. Jones

"INTRODUCTION The cooperative investigation dealing with the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the New England Telephone and Telegraph Co. in Boston, Mass. and surrounding territory, was continued during 1934.The method and procedure of conducting the survey for 1934 were the same as those followed heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. M. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner, chief engineer, Experiment Stations Division, U.S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing both men and information for the work.The New England Telephone and Telegraph Co., through Chief Engineer G. K. Manson, R. F. Esterbrook, H. G. Crush, and A. J. McCarron, cooperated by assigning a telephone company employee for the test truck. The company has borne its proportionate share of the expense and has taken an active interest in the work during the year. The test crew was operated under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and 7. M. Goodwin, vice president of the Boston Consolidated Gas Co."

May 1, 1936

By W. D. Mcmillan

Although the Shafter district of Presidio County, Tex., is principally renowned for silver production from the Presidio mine, the occurrence of lead-zinc ores in the western part of the district has been known for at least 50 years, and there has been some production. An area of about 3 square miles in the vicinity of an extending westward from the Presidio mine was investigated in detail by C. P. Ross of the Federal Geological Survey in 1934. In the fall of 1943, A. B. Needham, an engineer of the Bureau of Mines, called the attention of the Geological Survey to the area west of that included in Ross's map, and requested a detailed investigation of that area by the Survey in advance of development by the Bureau of Mines. After a brief reconnaissance by the Survey in the spring of 1944, detailed studies were made by Federal geologists in the summer of 1944, during which about 450 acres were surveyed, on a scale of 1 inch to 100 feet. Recommendations for the exploration of certain parts of the area were made in the accompanying report.

Jan 1, 1949

By C. C. Blade

"This report on the properties of motor fuels sold through service stations ni the Unietd States is a continuation of a series of reports made in accordance with a cooperating agreement between the Coordinating Fuel Research (CRF) Committee of the Coordinating Research Council (CRC)3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941.4/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.4/The present report presents analytical data for 1,381 samples, representing the products of approximately 75 companies. Most of the samples represented in this report were secured during July and the first half of August, 1945. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples – regular-price, premium-price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gasoline are not considered adequate to represent this type of motor fuel, data for the analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows: Regular-price, 733 samples, 229 items, and 57 brands; premium-price, 504 samples, 197 items, and 56 brands; third-grade, 84 samples, 28 items and 12 brands. The meanings of these terms as sued in the surveys are as follows:"

Jan 1, 1946

By Lloyd M. Kniffin

[This paper is one of series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United States. It describes the mine of the Hanover Bessemer Iron & Copper Co. at Fierro, Grant County, N. M., which is the only operating iron mine in the southwestern part of the United States. This mine is in a district noted for the great variety of ores that it produces. Within a small area, as shown is Figure 1, there are noteworthy deposits of nearly all the common metals. The ore occurs in lenticular masses dipping at about 50°. An underhand stoping method has been developed that requires but a very small amount of handling of ore. As the ore is very irregular in iron content and also in the distribution of the impurities--chiefly sulphur, silica, and magnesia--a method has to be used that will permit selective mining and will also allow ore and waste to be taken out separately as conditions change. A magnetic cobbing plant raises the grade of the ore shipped about 10 per cent.]

Jan 1, 1930

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. .It presents analytical data for 4, 457 samples, representing the products of 92 companies. The samples were collected by companies during June, July, and August 1956, As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is on page 5.

Jan 1, 1957

By John M. Devine

Hydrogen sulphide associated with natural gas was noted as early as at Point Albino, Canada. The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence was by no means common. However, in recent years, with the development of the producing zones of test Texas and the Texas Panhandle, the Production of "sour" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor--frequently a major problem--in the drilling and operation of many wells in those areas. The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen iron the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.

Jan 1, 1931

By D. Bienstock

A rig was constructed to burn 100 to 125 lb of coal per hour at 4,000° F in a cyclone burner with oxygen-enriched air preheated to 1,500° F to ascertain the problems in the coal-fired MHD generation of power. Potassium carbonate was added to the coal at several concentrations up to 1.23 g-moles/kg of coal (17 lb K2C03/100 lb coal). Boiler-tube materials maintained at wall temperatures of 800° to 1,500° F were exposed to the combustion effluent of 1,800° to 2,500° F. Practically complete removal of sulfur dioxide from the stack gas was achieved with the seed addition. Nitric oxide formation followed theoretical expectations at combustion temperatures with some decomposition of the NO occurring as the gas cooled flowing through the system. Nitrates in the fly ash were less than 1.7 percent of the total fixed nitrogen. With aqueous extraction of the fly ash a maximum recovery of 75 percent of the potassium was obtained. Haynes 25 was unattacked at a wall temperature of 1,500° F in combustion gas at 2,500° F; the stainless steels 310, 316, and 446 were resist-ant at a metal temperature of 1,100° F in gas at 2,100° F.

Jan 1, 1970

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

On December 16, the General Services Administration (GSA) suspended weekly sales of surplus silver from the national defense stockpile because Congress approved the Defense Appropriation Act, which contained an amendment to halt silver sales. The amendment, introduced by Senator James A. McClure (R., Idaho), prohibits sales for 6 months while the impact of the sales and alternative methods of disposal are evaluated. The GSA sold 2 million troy ounces since sales started October 14. 46.5 million troy ounces were authorized to be sold during this fiscal year and an additional 58.6 million troy ounces were authorized to be sold over the following two fiscal years. The stockpile held 139.5 million troy ounces of silver when sales began in October. Brush Wellman, Inc., a vertically integrated producer of beryllium products announced plans to modify its Delta, Utah beryllium concentrate processing facility to utilize beryllium concentrates containing as little as 7% beryllium oxide. The company plans to invest $2.5 million for this modification with completion expected in mid-1983. Implementation of this plan to consume lower grade beryllium minerals will significantly increase world reserves of beryllium concentrates.

Jan 1, 1981