Search Documents

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By F. Fraas, J. E. Conley

"The problem of recovering potash from the mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O), occurring in large quantities in the salt beds of Texas and New Mexico, has been under investigation at the Nonmetallic Minerals Experiment Station of the U. S. Bureau of Mines continuously since 1928. Most of the results previously obtained have been published in technical journals and in a series of Bureau of Mines Reports of Investigations.The experiments described in the present report were performed to ascertain whether a continuous countercurrent extraction of calcined polyhalite by hot water would yield satisfactory recoveries and concentrations of sium sulphate in the top liquor. Previous investigation by Storch 4 had shown that the rate of solution of uncalcined polyhalite was too slow to be of value in an industrial process, and Storch and Clarke 5 had demonstrated that calcination of the polyhalite greatly, accelerated the rate of solution in hot water, allowing most of the potassium sulphate to be readily extracted."

Sep 1, 1933

By Ellis S. Hertzog, James R. Cudworth

Tremendous interest has been evidenced in the subject of dewatering and drying ooal for the past 10 years, and yet little effort has been made to summarize the literature, at least so far as this country is concerned. Only a few published articles have dealt solely with dewatering and drying coal. In most cases the subject has been discussed briefly, either in general terms or as to specific installations. It is desirable that a compendium be prepared collecting in one place information on the dewatering and drying of coal, the needs for this process in various fields, the available equipment, and the current American practice in regard to it. This work was underta..lten by the :Bureau of Mines in cooperation with the University of Alabama. New coal-washing plants in which various types of dewatering and drying equipment were in operation were visited in-Pennsylvania; Ohio, India...~a~ and Illinois. The dewatering·and drying of coel has .been studied in this coimtry by the Surface Preparation ·Committee of the ·coal Operato~s• Committee of the .American Mining ·Oongress. In GermaIJY .it has received the special attention of the Reichskohlenr·at, and in Great Britain of the Utilization of Fuel Commi-t-tee of the Insti ti.ite of Min"ing Engineers.

Apr 1, 1938

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By O. W. Owings

"The handling and transportation of explosives and explosives supplies are inherently hazardous owing to their sensitiveness to impact and flame or electric arcs and sparks. Many accidents have occurred in the past during transportation of explosives, especially when they were carried by individual miners on man-trips. When electric haulage became the usual mode of transportation and shots were fired electrically, the hazards of carrying explosives and supplies on man-trips were fully realized, and in some mines all explosives were placed in one car, usually at the rear of the trip. Far-sighted managers saw the danger of this practice and provided separate trips for delivering explosives. This step was a definite advance in safety, but the latest achievement is the construction of special, rugged, nonconducting cars.Many coal-mining men have shown considerable interest in the construction of safe cars for explosives during recent months. Undoubtedly many others are interested in this phase of safety, therefore this circular is issued to give information on cars of this type now in use.Car A (fig. 1) is essentially a closed inner box separated from an outer box by an insulating lining of rubber. The double box is attached to a standard steel chassis that has spring journals and electric welding instead of certain rivets. The chassis is equipped with roller bearings. The over-all length from pin to pin is 11 feet, 9 inches; the wheel base is 54 inches, the track gage 42 inches, and the capacity eighteen 50-pound cases of permissible explosives. The box is 10 feet long, 6 feet wide, 3 feet high at the top of the arched roof, and 2 feet 9 inches at the edges. The top of the car is 46 inches above the top of the rail.The inner box is insulated from the outer box by two pieces of 1/4-inch switchboard.-insulating matting cemented together. To cover the top, two ends, two sides, and the bottom of the box requires 320 square feet of the l/4- inch matting.The walls are well-seasoned tongue-and-groove oak, 1 1/4 inches thick and 2 3/4 inches wide. A 1 1/4-inch air space is maintained by oak strips between the outer wall and the two thicknesses of 1/4-inch rubber matting. The inner box is made of 7/8-inch, well-seasoned, tongue-and groove oak fitted closely against the insulating matting. No nail, rivet, or bolt extends through the rubber insulation.The floor of the outer box is secured to the chassis by two sets of bolts through an intermediate piece of well-seasoned oak. One set of bolts is countersunk from the top of the intermediate piece of oak, and the other set is countersunk from the bottom. The countersunk portions are filled with ""insulate,"" an insulating compound. Adjacent bolts are at least 6 inches apart.The bed of the inner box is divided into six compartments by transverse strips of wood at the bottom and partitions near the roof. Each compartment accommodates three 50-pound cases of explosives. This arrangement prevents cases in adjacent compartments from touching, so that there is no possibility of end thrust of the entire load of explosives. Each inner compartment is 21 inches high, 5g inches long, and 16 1/4 inches wide. Separating strips at the floor are 3 inches wide and 1 1/4 inches thick. The outside dimensions of the 50-pound cases of explosives used are 17 1/2 inches long, 13 1/2 inches wide, and 12 1/2 inches high."

May 1, 1940

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

A compilation of papers presented at the Fifth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on July 30, 31, and August 1, 1980. Papers cover areas of electromagnetics/power systems, power systems, monitoring and control, and communications.

Jan 1, 1980

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By A. J. Kauffman Jr.

The Petrographic Section of the Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg., annually examines thousands of minerals and rocks. Samples are received from mining, engineers, prospectors, and government agencies, both State and Federal. During the past 2 years certain uncommon minerals have been identified in the samples submitted. Eleven occurrences have been selected for reporting in detail. These selections were made because in most cases a new locality is involved. The data reported are the result of application of the latest techniques, and widely disseminated references concerning each mineral have been added for completeness. Several occurrences have been described by other investigators; in those cases new data have been supplied to supplement the already published information on these occurrences. No uranium-bearing minerals have been included; they will be treated in another paper. The Bureau of Mines does not make chemical analyses or assays for individuals or firms In direct competition with private laboratories. Mineral¬ogical examinations, however, are made for prospectors and the general public. Such examinations a call surface to determine whether the sample in question has possible commercial value. If it has apparent value, the sender is so informed, and suggestions as to its .Arc, development and marketing are offered. The latest scientific apparatus is available to aid in identification. The apparatus includes microscopes, both wide-field and polarizing, a Bunsen-type spectroscope for visual observation of the Zinc and band spectra of many elements, differential thermal apparatus for the examination of hydrous material, apparatus for cutting and mounting either thin sections for study in transmitted or polished surfaces for reflected-light studies, and a high-intensity magnetic separator for concentrating minerals according to their magnetic susceptibility. Also, available, but not an integral part of the Section, are several laboratory-type Geiger counters, a grating spectrograph, and X-ray diffraction apparatus. If need be, all of these tools may be employed to identify a mineral or rock.

Jan 1, 1950