Search Documents

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By John F. Elliott

Six major trends that have had and are continuing to have major effects on the use and supplies of pig iron and scrap in the United States are (a) gradual replacement of the basic open hearth furnace (OH) by the basic oxygen furnace(BOF); (b) use of the electric furnaces for the production of plain-carbon steels, a trend which is closely related to the first; (c) United States changing from being a net exporter to a net importer of steel; (d) replacement of ingot casting by strand casting; (e) increased exportation of scrap; and (f) the lack of growth of the capacity of the U. S. steel industry to produce pig iron in the last 5 to 8 years. This report gives an analysis of the relationships between these trends and the use of processes for the production of raw steel in solidified form.

Jan 1, 1975

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in the' production of crushed stone. These studies, made at quarries scattered over the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these reports dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The present circular discusses analyses of the time Studies of the haulage systems at the same quarries. OBJECT OF STUDY The pressure of business problems frequently requires the entire atten¬tion of quarry management and in consequence internal plant economies often are neglected, Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that similar studies of many plants by impartial engineers would disclose possibilities for cost reduction or greater efficiency in internal plant processes.

Jan 1, 1939

By James J. Olson

This report summarizes the results of a review of foreign coal mining literature conducted under the Bureau's Advancing Coal Mining Technology program. In addition to a discussion on the historical development of mechanized longwall systems, and the current state-of-the-art method in Europe, this report summarizes the previous and ongoing Bureau efforts to adapt longwall technology to U.S. conditions. The bibliographic section of this report, divided into major categories such as mine design, face management, roadway development, strata control, powered roof supports, coal winning, conveying, and automation, contains over a thousand individual entries. The purpose of this report is to provide U.S. mining engineers with background information on longwall methodology and equipment developed in foreign countries (principally Europe). The Bureau of Mines, as part of its Advancing Coal Mining Technology program, is funding R&D projects to demonstrate that the longwall mining method, successfully used in the deep mines of Europe, can boost productivity and improve safety in certain U.S. mines.

Jan 1, 1977

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in the production of crushed stone. These studies, made at quarries scattered over the eastern and southeastern parts of the United States, have not been completed, but to make results available to thee industry as early as possible it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these reports dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The present circular discusses analyses of the time Studies of the haulage systems at the same quarries. OBJECT OF STUDY The pressure of business problems frequently requires the entire attention of quarry management and in consequence internal plant economies often are neglected, Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that similar studies of many plants by impartial engineers -would disclose possibilities for cost reduction or greater efficiency in internal plant processes.

Jan 1, 1939

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By George H. Johnson

This report describes the procedures and summarizes the results of an investigation of surface subsidence above caving blocks at the San Manuel mine, San Manuel, Ariz., in order to obtain quantitative information on subsidence and ground movement caused by mining large volumes of ore. This investigation is one part of an overall study of rock mechanics being undertaken by the Bureau of Mines. Attention was given to the improvement of a rapid and precise method of surveying a large number of subsidence pins and cracks in the surface terrain. Photogrammetric methods were used as an adjunct to the triangulation subsidence surveying as well as in ordinary topographic work Maps of various kinds were prepared to show the results obtained. The computation of the survey notes was programed for an electronic digital computer at a saving of time and expense over the use of a desk calculator and trigonometric tables.

Jan 1, 1963

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1969 (July 1: 1968, to June 30, 1969) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in the outside press. These publications are referenced in part 1 by underlined numbers in parentheses. Other publications, which are not abstracted, are cited in footnotes throughout the paper. ACKNOWLEDGEMENTS The Bureau acknowledges the support received through cooperative agreement in fiscal year 1969 from the Manufacturing Chemists Association. It also acknowledges the sponsorship by the following Government agencies of research conducted during that period: Department of the Air Force, Department of the Army, Department of Health, Education, and Welfare, Department of the Navy, Federal Aviation Administration, National Aeronautics and Space Administration, Space Nuclear Propulsion Office, and United States Coast Guard.

Jan 1, 1970

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972