Search Documents

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By H Leonard Mangum, Victor C. Bryan, Dan McCutchen

Recently there has been an unprecedented marketing effort to promote the advantages of various non-electric initiation systems. This activity has probably been influenced by a major manufacturer's decision to discontinue electric detonator production. Subsequently, distributors of explosive materials, rather than introducing new electric detonator brands, are emphasizing the use of existing non-electric systems. In many cases, such methods fill the need of explosive users in the quarry industry. However, the use of any initiation system should be based on performance, rather than the bent of the market or convenience to the supplier. This analysis is an evaluation of the performance of non-electric systems with emphasis on double trunk line and loop (redundant), as compared to precise electric detonators in use by Martin Marietta. Redundant non-electric detonators, even though more costly, offer the most reliable method of non-electric initiation. However, state-of-the-art precise electric detonators give the best overall performance, except in an environment involving extraneous electricity.

Jan 1, 1990

By R Ludeling, Klaus G. Hinzen, Ulrich Steiner, Friedrich Heinemeyer, Peter Roh

A method for hybrid modelling of blast vibrations in time domain is developed. Field seismograms of single shot experiments are combined with computer simulations. In this way firing times of blastholes in a pattern can be optimized due to diverse criteria like maximum velocity amplitude and frequency content of the vibrations.

Jan 1, 1987

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Dale S. Preece, Ruilin Yang

"Air-decking has been used frequently in blasting for many decades. It has been asserted that an air-deckcan alleviate excessive shock pressure from the detonation of a charge thereby producing better energy distribution in a blast overburden, for example. Research on air-decking has been active and various theories have been postulated that mostly support the effectiveness of air-decking for improved blast efficiency."

Jan 1, 2017

By Luis Huaroc, Augusto Sotomayor, Erick Rodriguez, Paulo Fernández, José Ricaldi, Luis Alejandro

The application of the Kuz-Ram model for the prediction of fragmentation is used worldwide, in Coimolache Mine it was used to determine blast domains and optimize the process by obtaining drilling patterns that meet a required X80 and reducing the uncertainty of drilling.

Feb 1, 2020

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Raúl Mondaca Aracena

Mantoverde mine requires increasing its production level to double. EMTS - Projects performs far and near field vibration studies to make changes to the D&B design and sequences, in order to equalize the current vibration levels, applying massive blasting in its process.

Feb 1, 2020

By Emmett J. Ientilucci, Martin Held, Xuesong Liu

Mining is crucial for advancing technology and science by providing essential resources and materials. Quarry blasting, a necessary process in mining, releases these resources and chemicals, driving research and engineering improvements. However, NOx (nitrogen oxides) is an undesired contaminant produced during quarry blasts, posing a significant negative impact on mining activities. Therefore, detecting and quantifying NOx emissions is essential for designing effective blasts, analyzing their dynamics, and reducing contaminant production. Image processing and machine learning, including deep learning methods, have been applied to solve smoke plume detection and segmentation tasks. Most research has focused on smoke from campfires or forest fires, which are important for early fire and smoke detection. However, there is limited research on quarry blast smoke using machine learning methods, which presents challenges for recognizing the smoke plume from complex background scenarios and objects, including collapsed rocks, scattered soil dust and dirt, and the dynamic movement of the scene due to blast vibrations. Detecting NOx within the smoke plumes is further challenging because NOx must be distinguished from the overall smoke plume, as they share many common spatial features. To resolve this issue, we propose an ensemble method for NOx detection that combines smoke plume segmentation with NOx fume detection. First, we apply a smoke plume segmentation model to identify the smoke plume regions. Then, we use these masked-out smoke plume regions to detect NOx based on its unique color features. The first stage of the ensemble method helps block out complicated confusers in the background, such as reddish and brownish dirt. Next, we specifically design a color classifier for NOx to further improve its sensitivity. We evaluate the overall video-wise performance using accuracy, false alarm, and miss rates based on sampled image frames from videos. Additionally, we assess the mean Intersection over Union (mIoU) for smoke plume segmentation and the mean Average Precision (mAP) for image-wise performance from an algorithmic perspective. In summary, this paper represents the first attempt to apply machine learning approaches to NOx detection in a memory-efficient and time-efficient manner.

Jan 21, 2025

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed. Based on an ellipsoidal shock shape approach, the proposed model uses the quasi-one dimensional theory for the axial flow solution and combine the post-shock sonic flow criteria with some limiting conditions for the explosives’ unconfined radius determination. Due to its attractive fitting capability for unconfined detonation experimental data, the model offers the possibility to predict the non-ideal detonation state for any diameter, resulting in a full mapping of the diameter-effect curve of the explosive. Thus, the proposed engineering approach is used to model the main properties of some of the most common ammonium nitrate-based explosives used in mining and quarrying industries, including the complete axial flow solution.

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed.

Feb 1, 2020

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By Dae-Woo Kang, Sang-Wook Kim, Shin Lee

The Air-tubes blasting method is provided in which a series of aligned boreholes are charged with explosive s and air tubes in a predetermined blasting pattern. The air tube is composed of cylindrical flexible tubes which have a predetermined width and length to be fit with the site boreholes. Within a preferred formation, each borehole is charged with the explo sives and detonators with an air tube installed just above the explosives. Stemming materials are filled above the air tubes. At the limestone mine of Sung-Shin Cement Co., in South Korea, these blasting tests were performed by a diameter 102 millimeter and 15 m long boreholes with the charging length of explosives was 8m to 10 m by the total weight of explosive 40 to 50 kg with 3m to 6m air tube which has a 76 mm diameter, and 1m to 3m stemming cover. Blasting results showed the about 10% to 30% explosives savings available and especially, the about 20% to 50% reduction of ground vibration with the low noise measures around 2dB to 5dB by this new blasting method which was compared with the conventional blasting methods. The explosives and air tubes may be alternately charged along the boreholes. The use of air tubes which were charged above an explosive layer allow to form the quantitative air decking in every blast hole. Therefore, the Air-deck effect can be easily obtained through this blasting method, and also easy to increase the fragmentation rate resulting in the more suitable mucking procedures at the working site with the minimum usages of explosives for the better economic operations in mine quarries.

Jan 1, 2005

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By T. Palangio

Most blasters wouldn’t think of initiating a shot without a seismograph to record vibration and air blast results. Some might even measure the velocity of detonation but few surprisingly record the event on video, photo document loading conditions or take pictures before and after the shot. This paper discusses digital imaging, the equipment, methods, techniques and information that can be learned from digital pictures taken in the field during blasting operations. The guy who said “a picture is worth a thousand words” probably understated it.

Jan 1, 2008