Search Documents

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By A. David Miller, Douglas M. Barber

"The Rocky Mountain Arsenal was used by the military to produce chemical warfare agents and incendiary munitions for use during World War II and later by private companies for the production of industrial and agricultural chemicals. After an investigation performed in accordance with CERCLA confirmed significant levels of contamination due to the common industrial and waste disposal practices of the era and the discovery of over 300 species of wildlife inhabiting the land the Rocky Mountain Arsenal became a wildlife refuge and contamination cleanup efforts began. Three lime basins originally used to treat wastewater from the chemical production were decided to be contained in place, requiring a seepage barrier installed around the perimeter of the site to further prevent groundwater/contaminant migration. This case study will discuss the successful installation of a soil-bentonite cutoff wall around the area using deep soil mixing. Highlights of this case study will also include a discussion of the challenges faced due to construction activities performed with Level B Hazmat PPE requirements as well as added challenges brought on by the Winter season, after the project was delayed due to a positive air monitor detection for the chemical weapon Lewisite during construction of the work pad.INTRODUCTIONThe Rocky Mountain Arsenal (RMA), located just outside of Denver, Colorado, was established by the United States Army in 1942 to produce chemical warfare agents and incendiary munitions for use during World War II. Following the war, and as weapons production decreased, portions of the site were leased to private companies for the production of industrial and agricultural chemicals. The principal lessee, Shell Oil Company, manufactured mostly pesticides at RMA facilities from the early 1950s to the early 1980s.In 1984 an investigation began in accordance with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and confirmed significant levels of contamination due, in large part, to the common industrial and waste disposal practices of the era. It was also discovered that over 300 species of wildlife inhabited the land in the absence of regular human activity, including a group of bald eagles, leading to the passing of the Rocky Mountain Arsenal National Wildlife Refuge Act in 1992."

Jan 1, 2015

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Antonio Kodsy, Lutful Khan

A research was carried out to test the possibility of reducing the pullout resistance of metal sheet piles driven in clay soils using Electrokinetic (EK) conditioning. The hypothesis was applying an electric gradient for a certain period of time should reduce the adhesion between the clay soil and the sheet piles. Tests were conducted on bench scale thin stainless-steel metal plates embedded in pure kaolinite clay, and mixtures of kaolinite clay and sand. The pullout resistances were determined after 20, 40, and 60 minutes residence times of steel plates in the soils before and after EK conditioning under an electric gradient of 1500 V/m. In kaolinite clay, the pullout resistance showed linear reduction with the duration of EK conditioning and about 60 % reduction in pullout resistance was observed after 60 minutes EK conditioning. For the kaolinite-sand mixtures, the pullout resistances were reduced by about 70% and 80% for 20% and 30% sand contents respectively after 20 minutes EK conditioning and showed no significant improvement with the increase in conditioning duration. It was concluded that the proposed electrokinetic conditioning process could potentially reduce the pullout resistance of metal plates embedded in clay and clayey soils. SHEET PILE WALLS Sheet pile walls are typically used at waterfronts as retaining structures or during the construction phase to shore the soil and avoid collapse of the excavations. When used as permanent structures, sheet pile walls are not removed after the completion of the project. However, as temporary support, they are extracted after the completion of the project and reused. In pure clay soils the extraction processes often becomes a challenge requiring very large pullout forces which could damage the sheet piles. There is a research need for developing an efficient method of sheet pile extraction from clay soils addressing the issue of pullout force reduction. However, very few researches have been conducted regarding the extraction techniques of sheet piles and their economic effect on the cost of a project. In this study a novel method for reducing the pullout resistance of sheet piles in clayey soils using electrokinetic conditioning was explored. The hypothesis of this research is that the electrokinetic process in soil/water system, specifically electrophoresis and electroosmosis, could be used to loosen the sheet pile walls embedded in cohesive soil and hence reduce the required force of extraction. The aim of this study was to test this hypothesis through laboratory tests carried out on steel plates embedded in cohesive soil samples. The pullout forces of the steel plates before and after varied duration of electrokinetic (EK) conditioning were evaluated and compared. The process was also investigated for clay-sand mixtures.

Jan 1, 2019

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Alice Arana, David M. Cacoilo, Joel L. Volterra

"To make space for the new South Ferry Station in lower Manhattan, engineers and contractors carved out a new tunnel beneath three operating subway tunnels and tangentially to yet another tunnel. Creating the space required the design and construction of complex temporary excavation support and underpinning systems and the design and installation of real-time monitoring systems. Construction for the new station and tunnel was mainly cut-and cover in a mixed-face area of soil and rock approximately 2,000 linear ft long, 60 ft wide and up to 70 ft deep. Close coordination between the design/build team and the project owner, the Metropolitan Transportation Authority (MTA), was critical.With the construction of this $400 million project, the MTA and New York City Transit (NYCT) are correcting the numerous physical and operational deficiencies of the existing station and improving the lives of millions of commuters. Built in 1905, the original South Ferry Station is on the IRT Broadway–Seventh Avenue Line of the New York City Subway and is the southern terminal of the #1 subway service, which forms a loop to return uptown. The station has a sharply curved single platform on the outside of the outer track of a two track loop. This platform is short and does not allow the rear five cars of a normal 10-car subway train to load or unload. In addition, once the train stops at the station, commuters wait while retractable floor grates bridge the gap created between the platform and the subway car doors, and then they have only one exit from the station. Spray nozzles keep the tracks lubricated to reduce the train wheels’ friction caused by the tight curve. The sharp curvature of the loop and the inability to use half of the subway car doors slow train operation. With the new ADA-accessible station, 10-car trains will be able to open all doors, and additional entrances, escalators and elevators will greatly reduce travel times."

Jan 1, 2008

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Four drilled shafts, two on each side of the bridge (NJ and NY), were load tested using the bi-directional axial load method. Axial test results demonstrate that RQD, taken by itself, is not necessarily a reliable indicator of side or base resistance. High recovery with low RQD can be a function of horizontally bedded siltstone and shale where the individual pieces of core do not exceed four inches, but may still provide very high side and base resistance. Axial testing was followed by a lateral rapid-load test (Statnamic) on each of the same four shafts. In addition, one of the shafts was subjected to a static lateral load test to validate the rapid-load method as being representative of static loading conditions. Results of the axial load tests provide the basis of unit side and unit base resistances used in the LRFD design of the rock sockets for axial loading, while results of the static and Statnamic lateral load tests were used to calibrate p-y curve parameters used for design under lateral and moment loading. This paper describes implementation of the load testing program and its role in the design process.INTRODUCTIONDesign of drilled shaft foundations for the Goethals Bridge Replacement (GBR) required load testing in order to validate the parameters used for calculating geotechnical axial and lateral resistances. The bridge, including foundations, was designed in accordance with the AASHTO LRFD design specifications, 6th Edition (2012). The bridge owner is the Port Authority of New York and New Jersey (PANYNJ). One of the PANYNJ project requirements was stated as follows:“Perform a minimum of two (2) separate axial compression load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology to verify the design assumptions and construction procedures. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.Conduct a minimum of two (2) lateral load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.”"

Jan 1, 2016

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.