Search Documents

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Bengt H. Fellenius

It is a truism that in the design of pile foundations one must consider both capacity and settlement. As to capacity, most basic text books contain simple methods of design of capacity of single pile. More sophisticated methods are the subject of many journal papers. However, methods for design considering settlement of pile foundations are scarce. (Most confuse settlement with the movement due to load-transfer?the transfer of load from the pile to the soil). Furthermore, for both capacity and settlement, most methods include several simplifying assumptions regarding soil layering and neglect the effect of the frequently occurring fill and excavations, as well as changes of the groundwater table and pore pressure distribution. Therefore, the methods may provide qualitative results, but not quantitative. Because of this situation, pile design often appears as somewhat of a guessing game and a very subjective?and risky?occupation. This need not be. Pile foundation design is controlled by three factors: capacity, strength, and settlement requirements and these have been combined in a method called "the unified design of piles and pile groups considering capacity, settlement, and negative skin friction" (Fellenius, 1984; 1989), which method is summarized in this guide.

Jan 1, 1991

By Allen B. Stanton, Parthiv Brahmbhatt, Michael Grimm, Stanley L. Worst

Constructing a circular shaft consisting of secant piles has its own complications which make it more difficult than typical drilled shaft construction. Add to that performing under low overhead powerlines and sitting inside of a 40-foot deep, 50-foot diameter shaft and it becomes more about logistics than the actual drilling. The complexities associated with the Romeo Arm Interceptor Segment 5 Lining project are the focus of this paper, delving into the details that made it work successfully.

Oct 1, 2022

By Ashraf M. Eid

Most research dealing with the problem of laterally loaded piles has been the response of individual piles subjected to lateral loads and/or bending moments. However, piles are seldom used individually but are normally constructed in clusters or groups. Little information is available of the effect of pile-soil-pile interaction (PSPI) on the performance of the group. This may be attributed to the difficulty of carrying out full-scale tests. Such tests are prohibitively expensive and require special installations to provide the required large lateral loads. The problem of laterally loaded single piles or pile groups involves the complexity of extending the theoretical solutions to the limits where the actual soil behaves nonlinearly. As the load increases, the elastic soil behavior cannot be adopted for design. Nonlinear soil behavior or the elasto-plastic behavior is evident. This research consists of experimental and theoretical models. The experimental work was conducted on models of free head pile groups in different configurations. The piles were in a sand formation and compared to the behavior of a single pile. The possible factors that influence the group behavior could be visualized. The experimental data was also compared to the widely used theoretical approaches to determine their adequacy. The analytical model makes use of the finite difference approach to calculate the soil non-linearity. A new approach equates the measured ground deflection and maximum bending moments of each row at every load level with the analytical model of single pile. This is the Deflection-Moment Fitting (DMF). The most suitable non-linear soil modulus modes and row contributions could thus be determined. Design of pile groups can be based on data pertaining to soil characteristics of the single pile. Results of the analysis were consistent with other approaches and proved to be adequate for design.

Jan 1, 2005

By Max Gwynn, Tony Suckling

"The new Wembley Stadium is the most spectacular soccer stadium in the world, built to the highest specifications, using the latest technology and offering visitors an unrivalled match-day experience. Wembley Stadium is the home of English soccer, dating back to 1918 when the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Empire Stadium, as it was originally known, was completed in 1924 in just 300 days and cost £750,000 ($1.4m). It was finally closed in 2000.The new Wembley Stadium, which opened in 2006, features fully covered seats for 90,000 fans and a striking arch that sits above the northern half of the stadium. With a span of 315 m (1040 ft), the 133-m (440-ft) tall arch is the longest single-span roof structure in the world. It supports the entire weight of the northern roof and 60% of the weight of the southern retractable roof. This means there is no need for columns within the stadium and ensures unobstructed views.Multiplex Constructions (UK) Ltd. employed Stent Foundations Limited to construct the £10m ($19m) foundations package for the new stadium. The scope of works for the foundation package included the design and construction of all foundations, including all main works piling, temporary works piles for the arch and roof, and tower crane piles. The scope also included trial piling and pile testing, setting out and removal of spoil.Piles were constructed by using bored cast-in-place techniques with both hydraulic and traditional crane-mounted rigs. Stent also installed sheet-piled walls at three locations to the site’s northern boundary. In addition to the main contract works, Stent constructed a £2m ($3.8m) contiguous bored-pile retaining wall within the demolition and earthworks package (Figure 1). This work was carried out as a subcontractor to Griffith McGee."

Jan 1, 2008

By Seyyed Mehdi Radeghi Mehrjou

The current work investigates the behavior of inclined micropiles under seismic loads. The dynamic finite element method (FEM) was employed. Rayleigh damping was applied to the soil, and elastic beam elements were employed to model the micropiles. The micropile structure was assumed to have one degree of freedom as a column with concentrated mass. The numerical modeling of micropiles was performed to explore the effects of their inclination on their seismic performance within homogeneous soils with uniform stiffness. In addition, the effect of soil stiffness was studied by considering various stiffness in soil depth. The results from the studies have shown significant effects on the dynamic amplification and internal seismic-induced loads of inclined micropiles.

Sep 1, 2022

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

The pile inspector is a critical element in the quality control process necessary for a successful pile installation project. This guide is intended to provide the inspector with a basic understanding of only one of the many components of this process - the pile driving hammer. Pile driving hammers are used to install both bearing piles for structure foundations and sheet piles (and soldier piles) as used in retaining structures. In a single document, this guide offers a general presentation of the operation of the more common types of hammers the inspector is likely to encounter. It should make the information in the contractor&apos;s hammer submittal for the project more understandable. It should also provide an appreciation for the importance of a properly operating pile hammer. Prior to the start of most pile driving operations, the contractor will normally furnish a submittal to the engineer giving the specific pile driving equipment that he intends to use on the job. This submittal should include the make, model, and type of the intended pile driving hammer or hammers and their operating characteristics such as ram weight, rated energy, operating speed, external power requirements and, other pertinent information. Frequently, the operating characteristics are provided in the form of the manufacturer&apos;s specification sheet. The engineer will review this information and when he is satisfied, approve it and pass it on to the inspector. The driving criteria will have been determined by the engineer or others (the geotechnical engineer, consulting engineer, contractor, etc.) from the results of static analysis (for minimum penetration), driving during a test pile installation, Wave Equation analysis, dynamic formula, pile instrumentation during driving, static load test, or a combination of these or other appropriate analyses. The driving criteria can be a minimum penetration of driven pile length (embedded length), or a minimum (or maximum) blow count per unit of penetration. The pile inspector should become familiar with this information prior to the start of the job and should understand or seek help to comprehend the terminology and intent of each specification.

Jan 1, 1995

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By Donald R. Clark

Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0. Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs. The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths. Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary design.