Search Documents

By H. Cheng

The Bohai Oil Company has applied all together 11 jack-up oil drilling rigs (movable platforms) (1) which can be classified in terms of their forms of foundations into two types: the integ­ral mat and the column legged, as demonstrated in figure 1. Figure 1 a) indicates the entire structure of the sunk cushion type, i.e. the one with a box-like sunk cushion serving as its foundation by directly sitting on the sea bed. The length, width and height of the outer sides for the sunk cushion stand at 45.8 x 38.0 x 3.3m ( for Rig Bohai No.2 ) and 50.6 x 33.2 x 4.88m ( for Rig Bohai No.6 ), the relative areas of theirs being 1475m2 and 2008m2 respectively and both bigger than the plane areas of the rigs. With a view to realize a convenient drainage of mud while sinking, two holes of 14 x 14m and 32 x 18m in size are constructed in the center part of the sunk cushion. When work sets off, the underside of the sunk cushion operates as a foundation, the sunk cushion being connected to the platform by hull columns which transmit the load of the platform down­wards to the sunk cushion that passes it further onto the subgrade. [ ] Column legs for rigs may also be grouped into two categories considering their features: columns with and without boots. The bodies of boot columns are made up of trusses, whose bottoms, are boot-shaped with a big diameter. The diameter of boot columns of the rigs applied by the Bohai Oil Company shows bigger and it may reach 12 or 18m. In the boot columns, the transmission of the platform's weight into soil is done by the underside areas of boots. While in the case of the vertical columns, which are of cylinder columns of steel with sealed bottom ends shaped inverted arch, the entire drilling platform is supported by the carrying force delivered by the bottoms of these steel cylinders and the frictional force rendered by their outside walls. Such a type of columns is featured by a small diameter, 3m in general. Figure 2 exhibits the schematic diagram of sections regarding the two types of column legs.

Jan 1, 2010

By Cornelis Van Der Veen

Foundation piles, partly passing through unconsolidated compressible layers, suffer a downward drag that is called negative skin friction. The negative skin friction depends on the movement of the surrounding unconsolidated soil relative to the pile and on the friction between pile and soil as a function of that movement. The negative skin friction adds to the load on the pile. However as it is a function of the pile movement relative to the soil, the amount of negative skin friction to be taken into account to determine the allowable bearing capacity depends on the allowable pile settlement. In this paper this property is indicated by the factor µ. As under the conditions of ultimate pile bearing capacity negative skin friction does not occur, a factor of safety is introduced, which is lower than normal. Eventually a formula for the bearing capacity is given in which µ and both figure. The exact values for given circumstances have to be determined empirically. A few examples are given.

Jan 1, 2010

By Tony Suckling

The commercially available finite element program Plaxis has a key benefit over other finite element analysis programs in that it has a relatively simple user interface to input and output data. This benefit though may also be it?s weakness in that anyone, regardless of their grounding in geotechnical engineering, may use the program and produce results for design. It is essential, as for all engineering design, that the models are checked by competent engineers. This paper describes the key recurring problems found by the authors when checking Plaxis models, such as the generation of the initial in-situ ground stresses and the modelling of groundwater. Interestingly, the authors have not encountered similar problems when checking finite element models produced using other programs and conclude that this may be due to the higher calibre of modeller needed to use these other programs. The geotechnical industry is in a situation at the moment where senior managers who may not have been trained in finite element modelling are relying on less experienced staff who have had some training in modelling, either at university or post graduation. The quality of this training is variable and all organisations running easy to use programs need to be aware of the potential risks and dangers. Management procedures and engineering checks that are essential to validate the results of these models are described, assuming that those in charge are not experienced modellers themselves. The model checking process by competent persons is absolutely essential and it is hoped that this paper will help those organisations that do not have such procedures as part of their own internal Quality Assurance or design validation system. The procedures described are valid for all finite element programs.

Jan 1, 2010

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Michal Topolnicki

Deep Mixing Series: This article is the second keynote highlighted from DFI's virtual Deep Mixing Conference in 2021, for which Topolnicki served as a committeee co-chair Polish applications of deep soil mixing (DSM) technology occupy a leading position in Europe. That includes use for road and railway embankments, bridges, residential and industrial build- ings, silos, commercial centers, slabs, car parks and storage yards, excavation supports and cut-off walls. In fact, more than 350 road and railway viaducts and 200 wind turbines have been founded nationally on DSM columns, which are firsts on an international scale. This represents more than 1,200 imple- mentations by the Polish geotechnical industry. Considering the need to update DSM design recommendations, this article will attempt to summarize the best practices of wet DSM design and implementation, in particular. It draws on 20 years of experience and will high- light the properties and principles of the design of stabilized soil and lessons learned. Case studies are included to fur- ther understanding of the careful con- siderations needed with this technology.

Apr 1, 2022

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Robert Small, Amshu Chappa, Ihab Allam

The Biosolids Digester Facilities Project (BDFP) is located in southeast San Francisco. The jobsite is bounded by active Caltrain and Union Pacific Railroad tracks on the west side and the existing Southeast Treatment Plant (SEP) on the north, south and east sides. The existing SEP was constructed in the 1950s and portions of the facility have reached their operational life. The $2 billion BDFP will replace and relocate the outdated existing solids treatment facilities with more reliable, efficient and modern technologies and facilities. In addition, the nearby Bayview and Hunters Point neighborhoods will benefit from the improved odor control. MWH/Webcor, a joint venture, as the construction manager general con- tractor (CMGC) for the project. As part of an alternate delivery method set forth in the prime contract, the CMGC was permitted to propose the use of a core trade subcontractor partner for the SFPUC's approval to provide precon- struction services. The CMGC identified three major scopes (electrical, mechanical and foundation) where a core trade partner would be able to assist

Jan 1, 2023

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Manish Kumar

One of the recent advances in the field of testing of concrete piles is the Non-Destructive testing (NDT) of piles. This paper deals with a specific project where this technique was employed along with an extensive program of conventional testing methods to cross check the results. Conventional testing of the Bored, cast-in-situ piles involved taking full length concrete cores from piles to check physical properties such as core recovery, RQD, crushing strength and density of concrete. Additionally, a number of questionable piles were exposed and inspected and actual load tests were performed on selected piles. Concrete pour cards were used to compare actual Vs theoretical consumption of concrete. A direct comparison of the conclusions drawn from both these testing methods provided an excellent opportunity to better understand the intricacies of NDT technique. The study undertaken clearly indicated a need for developing clear guidelines and specifications for the use of this method of non-destructive testing of piles before the .method can be accepted as a useful quality control tool at the construction sites.

Jan 1, 1996

By Wang Lushuang

This thesis is devoted to the research of the interaction between pile and foundation soil by boundary element method (BEM for short). The interaction is simulated by the interaction between two different elastic mediums. The foundation soil is simulated by the two-dimensional elastic half-plane, and the pile by the two-dimensional elastic finite plane. Therefore, the calculating models made by the paper's author would come more closed to the actual conditions. The elastic behaviour of the interaction between pile and soil, and the whole course of pile ultimate load are analysed in the thesis, and the relevant applied computer programs "BEME", "BEMPA" are designed by the paper's author. The bearing power of single pile can be worked out by the program "BEMPA", it has compared with staic loading tests of pile, and the results are in conformity to actual conditions. So it can be drawn that the BEM for studying on interaction between pile and foundation soil made in the thesis is more simple, more precise and more practical in actual project.

Jan 1, 1991

By Jorj O. Osterberg

The practice of using side shear resistance in the design of drilled shafts socketed in rock is discussed. In the absence of field test data for the particular rock involved, the designer often neglects the side shear altogether or uses an extremely conservative value. The uncertainty of using strength data from compression tests on rock cores is discussed. Examples of full scale load tests are given which illustrate that even in the weakest of rocks, considerable side shear resistances are obtained, enabeling reductions in the depths of the sockets and consequent savings. Existing Practice. The existing design practice in using side friction/bond between a drilled shaft in rock or hard soil varies very considerably in different areas of the U.S., in different areas of the world, among different Geotechnical Engineers, and in the requirements of different building codes. In fact, the variation is so great that it is inconsistent and contradictory. For example, in Florida where fairly weak coral limestone and sandstone is prevalent, the general practice is to use side friction only and to allow no end bearing. In Chicago, Detroit, Boston and other areas where soft clay overlies stiffer clays, hardpan and limestone or other hard rock, the common practice is to allow for no friction and to use end bearing only, even though the lower portion of a shaft frequently penetrates stiff to hard clays and hardpan (glacial till) before bearing on hardpan or rock. In Hong Kong, if the hole is stabilized with drilling mud, no end bearing is allowed. In Boston (Thompson, Erikson, and Smith, 1989), two tests at two sites on 18 inch pipe piles penetrating 100 feet of soft clay and driven only inches into an argillite, tested 140 and 210 tons in ultimate side shear resistance. Certainly, with long drilled shafts, no matter how soft or weak the soil or rock is, some if not considerable side friction occurs, and where drilling mud is used, there must be considerable end bearing.

Jan 1, 1991

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By Sherrill Gardner

Vibratory drivers have been used since the 1930s to drive and extract piles. Vibratory pile drivers have the capability of significantly decreasing pile installation time, especially in granular type soils. However, they have not been widely accepted because of the uncertainty in estimating the bearing capacity of the driven pile. When driving bearing piles, the industry standard method for obtaining load carrying capacity of a pile installed with a vibratory driver is to redrive with an impact hammer. The advantage of improved productivity is lost with the redrive procedure. Currently, there is no other method to predict the capacity of these bearing piles installed with a vibratory driver. The Naval Civil Engineering Laboratory (NCEL) is making progress towards being able to estimate the bearing capacity of these piles. This paper describes field testing and corresponding analytical modeling of the vibratory driver-pile-soil system. The following sections describe the development of the numerical model and techniques for collecting field data. A discussion of the prediction of the pile driving process based on field test data is followed by suggestions as to the additional work that should be done to further verify the model to a point where it can be used with confidence.

Jan 1, 1987

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012