Search Documents

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By Knud Sinding

Environmental reporting by mining firms takes many forms and change frequently. The objective of these reports is related to increasing the legitimacy of mining firms with their diverse stakeholders. This study, focusing on internet-based reports, shows that there are considerable variations in reporting. This phenomenon is interesting because it belies the efforts pursued by leading industry members under iniatives such as the Global Mining Initiative and the Mining, Minerals and Sustainable Development project. The observed variation, both internally among reports and between reports and other industry policy statements, suggests that the industry needs to explore the possibilities for more convergence in terms of reporting quality. Based on theoretical constructs from the management literature we present a series of arguments defining necessary and sufficient conditions for durable and well-institutionalized reporting practices and standards.

May 1, 2002

By K. G. Stowe

"1. Introduction Mattagami Lake Mines and Orchan Mines operate zinc copper mines adjacent to one another near Matagami, Quebec, situated approximately 300 kilometres north-east of Rouyn-Noranda. (Note: Mattagami Lake and Orchan are in the process of being absorbed by Noranda Mines and will become Noranda Mines-Matagami Division). Both concentrators began operations in late 1963.The Mattagami Lake concentrator is capable of treating up to 3,500 metric tons per day of massive sulphide ore with a mineral composition shown in TABLE 1. The Orchan concentrator consists of two separate circuits - the Orchan circuit with a capacity of 1,050 metric tons per day and a custom circuit with a capacity of 825 metric tons per day. Throughout its operation, Orchan has custom milled ore from several smaller deposits in the Matagami district."

Jan 1, 1979

By E. W. Johnson

"The title of my paper is ""I 'Wonder Where The Yellow Went"". As you can readily guess, it is not related to an old-fashioned ""Pepsodent"" sales pitch! Rather, it concerns a situation which arises all too frequently in some gold milling operations, namely when actual ounces of gold production do not come up to estimated or projected ounces. The boss man scratches his head and wonders where the missing gold has gone and how it has disappeared. The problem, if one exists, is amplified if one forgets that an estimate is just that - an estimate - and not a hard fact - even though the numbers are produced by computers. And yet, from the point of view of engineering; financial and production planning and security; it is most desirable to tie together all data relating to production estimates, losses and actual production.In the course of this paper reference will be made to the term ""variance psychology"", to a few of the physical properties of gold and to the nature of its occurrence in Canadian ores, in relation to the topic under consideration. Activities which have a bearing on production estimates will be reviewed. These include: weighing, sampling, assaying, estimating residual losses and, in cyanide plants, gold precipitate production. Mention will be made of apparent, unaccounted for and unknown losses. In conclusion, I shall draw from personal experience and relate three examples of ""Where the Yellow Went''."

Jan 1, 1986

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By D. H. Rubisov, V. G. Papangelakis

Sulphuric acid pressure leaching is the process of choice to recover nickel and cobalt from laterites with variable iron and magnesium contents. The latter influences the acidity levels required for effective leaching of nickel and cobalt, and during leaching, iron is rejected in-situ as hematite. Classical solid/liquid separation is performed via a CCD circuit, the performance of which depends upon the size and shape of precipitated particles. In this paper, precipitates obtained by acid-leaching of various lateritic feeds at 270°C are characterized using SEM/EDX and laser particle size analysis. It is shown that as acidity increases, the shape of the precipitates gradually changes from platelets to spheres, thus improving the S/L separation properties of the residue. The use of hydrogen ion concentration “at temperature,” calculated from a speciation analysis, allows the explanation of this change of morphology independently of the type of the ore feed. The possibility of precipitating magnesium sulphate “at temperature” is also discussed. In order to take advantage of this precipitation for scale reduction (as has been proposed in the past) without compromising the residue quality, [H+] “at temperature” must be controlled within an optimum range.

Jan 1, 2000

By André van Wageningen

Since the beginning of this century Boliden Mineral and Atlas Copco have worked together in stages on improving the accuracy and quality of drilling. Navigation of the drill rigs with IREDES has been in use in the Boliden mines for several years. Recently the capability of the system has extended with map navigation to more accurately follow the ore in cut&fill mines. The system allows for changes on the individual round level to follow the ore without changing the whole design for the heading. Those changes are done in a CAD-system and remove the need for face markings and will allow for even better accuracy in both height and wall position. All the information between the CAD-system and the drill rigs is exchanged using the IREDES standard. This paper describes the workflow and the use of the IREDES standard.

Oct 1, 2009

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By B. Simser

Noranda?s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2004

By B. Simser, V. Falmagne

"Noranda’s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning.Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically."

Jan 1, 2004

Why Innovate in Mining? ?Obvious, right? ?Increase productivity and profitability ?Improve safety and ergonomics ?Improve our environmental record and eliminate liabilities ?Implement process control methodology ?Introduce information systems technology to gain control ?Low hanging fruit ?Reference ?Heather Ednie, Innovation CIM Magazine Feb. 2006 ?Peck & Skinner, Getting better bang for your buck with technology

May 1, 2006

By R. W. Nice

"The Similkameen Mining Company property is situated about 9 1/2 miles south and west of Princeton B.C. Owned and operated by Newmont Mining Corporation, mining is presently taking place in the Ingerbelle pit. At 15,000 tpd of 0.50% Cu ore the Ingerbelle pit is sufficient for about 8 years. Another 8 years ore supply is available from the old Granby workings of the Copper Mountain property which operated from 1927 to 1957.The pit operations commenced in late 1970 with the concentrator starting in March 1972. Designed and built by Bechtel Corporation under the supervision of Newmont the concentrator's design was based on single-stage crushing and single-stage modified autogenous grinding. The modification was installation of a crusher to crush the critical size build-up. The description of the operation follows.CRUSHERThe primary crusher is an open pocket Allis-Chalmers. 54"" x 74"" gyratory. The basic closed side setting is 8"". The crusher is fed from one side with 100 ton Electra-haul trucks. The crusher pocket discharges to a 96"" wide conveyor belt, then to a 48"" conveyor system including a stacker belt. The crushed product is piled on a stockpile with a capacity of about 30,000 live tons. This stockpile feeds the concentrator."

Jan 1, 1975

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By S. Haggarty

"Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Milling capacity is 3,400 SDT /Day with an average feed grade of 0.080 Oz Au/Ton. Gold processing involves three stage grinding including tertiary pebble milling, two stage cyanide leaching and filtering and Merrill-Crowe zinc precipitation.A summary of process improvements required to increase milling capacity above the initial design tonnage of 2, 700 SDT /Day are described -Installation of a 42"" x 65"" Allis Chalmers Gyratory crusher replacing a 42"" x 48"" Traylor jaw crusher.Installation of polyurethane screen panels replacing woven wire cloths on an 8' x 20 ft triple deck screen.Installation of a hopper clarifier to reduce filtrate turbidity.Automated control of solution balancing and effluent treatment circuits.INTRODUCTIONThis paper describes mining and milling practices at the Nickel Plate Mine and details post start-up process modifications which were required to attain design tonnage.Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Mining capacity from the open pit is approximately 32,000 TPD with an average waste/ore ratio of 8.4:1.Milling capacity is 3,400 SOT/Day, above initial design tonnage of 2,700 SOT/Day. Feed grade averages 0.08 Oz Au per ton yielding 85,000 troy ounces of gold per year."

Jan 1, 1991

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By R. W. Schutz

"Titanium possesses an exceptional and wide-range resistance to chlorides and their compounds when compared to most corrosion-resistant engineering alloys (CRAs) used in the chemical process industry. This natural resistance to chlorides stems from titanium’s protective, tenacious, and readily rehealable titanium oxide surface film, which is chemically stable over a wide range of pH and redox potentials in aqueous environments. This passive film explains titanium’s elevated resistance to anodic pitting, crevice and stress corrosion, and erosion-corrosion in aqueous chloride environments.Guidelines for successful selection and application of industrial titanium alloys are derived from an extensive laboratory test database and more than forty years of industrial/chemical service experience. These guidelines are simplified, and alloy corrosion performance is assessed with respect to four basic aqueous chloride service categories where selection or consideration of titanium is highly merited. An overview of historical titanium alloy applications in chloride-rich environments in a wide variety of process industries substantiates their exceptional chloride tolerance. These industrial titanium alloys are cost-competitive with stainless steels and nickel alloys, readily commercially available, and routinely fabricated and welded in the shop and field via well-established methods."

Jan 1, 2002

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977