Search Documents

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

Plant-Based Trials of Monitoring of Coal Flotation Systems Using Electrical Impedance Spectrum Technique

Sep 13, 2010

By B R, R Brooks, R Simcock, R Stewart

As environmental costs incurred by the mining industry become increasingly subject to critical analysis, new technology is necessary to ensure the further development of good relationships between the industry and community. Phytoremediation and phytomining are technologies that have the potential to capture the imagination and approval of the public. Phytoremediation , the in situ use of plants to extract heavy metals from a contaminated substrate, could offer an environmentally and cost-friendly alternative to traditional remediation techniques. Phytomining is the in situ removal of metals from a contaminated site or subeconomic orebody with the additional aim of recovering from the plant an economic amount of metal. Plants used in such operations, hyperaccumulators, accumulate large quantities of one or more target metals in their above-ground herbage. Upon harvesting and incineration, this plant material yields a low-volume, sulphide-free æbio-oreÆ, which can either be safely disposed of, or if the metal is of sufficient value, smelted. Investigations into the economics of phytomining nickel from ultramafic (serpentine) soils, showed that Alyssum bertolonii and Berkheya coddii could remove over 100 kg of nickel per hectare per annum from land with nickel concentrations well below the cut-off grade for conventional mining. It also appears possible to æinduceÆ the hyperaccumulation of gold into plants growing on gold tailings, or on stockpiled, low-grade gold ore. The plants used for phytoremediation and phytomining are useful colonisers as they are necessarily hardy and withstand extremes of salinity, metal toxicity and water stress that hinder the success of current revegetation procedures. As part of a rehabilitation operation, these plants may alter the geochemistry of a substrate making it more amenable to the growth of native species that should be used to restore a mining site to pre-operating conditions.

Jan 1, 1999

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. TheZapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level.   However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy. In the developed countries, government policies for the development of mineral resources have been progressively eroded since the early 1970s. At the same time policies for the environment and for native land rights have generally been carried out in a way that has reduced access to minerals and increased the cost and risks for prospectors and developers (Hancock, 1995). Since the end of the Cold War, the lesser developed countries (LDCs) have introduced policies to attract investment in their mineral resources that remained undeveloped under previous unstable or hostile regimes. The increased attraction of these LDCs and the decreased attraction of the developed countries has caused many Australian and North American companies to outlay increasing proportions of their budgets and capital investment in the LDCs.   Significantly, LDC policies for environment protection do not discourage exploration and mine development, Surveys of the relative appeal of the LDCs and the traditional mining countries of the developed world, rate Chile, Argentina and Indonesia ahead of Australia and Canada in terms of risk, delays and ease of doing business (Australian Mining Monthly, February 1994).

Jan 1, 1995

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

Leading Article from "British Medical Journal," London, 4th, November, 1944.Assuming that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid, Denny, Robson, and Irwin thought that if the solubility of siliceous material retained in the lungs could be suffciently reduced the usual fibrotic response could be diminished or prevented. They discovered that aluminum powder rendered siliceous material insoluble in vitro by coating the silica particle with a thin film of gelatinous hydrated alumina, which on drying formed crystalline alpha aluminum monohydrate. The presence of this adsorbed layer on the surface of the quartz was shown by staining it with aurin. That metallic aluminum dust produced no fibrosis in the lungs was demonstrated by dust-inhalation experiments on eight rabbits. Attempts were therefore made to prevent silicosis by mixing quartz with metallic aluminum dust.Animals exposed to quartz dust developed typical silicosis in about five months, but the addition of 1 per cent. aluminum powder prevented this even after exposure had been lengthened up to 22 months, provided the aluminum powder was of a particle size below 5. This year Crombie, Blaisdell and MacPherson have reported the treatment of 34 silicotic miners by the daily inhalation of fine aluminum powder freshly ground from small aluminum pellets in a specially constructed mill. Daily treatment began with five-minute inhalations, which were gradually increased to 30 minutes. Some of the men received 300 treatments, but the majority only 200. Out of the 34 cases thus treated clinical improvement was manifested by lessening or disappearance of shortness of breath, of cough, of pain in the chest, and of fatigue. In 15 cases the condition became stationary and remained so in spite of continuous employment in silica dust throughout the treatment. The progress of the disease was assessed by means of tests for respiratory function repeated at three-monthly intervals. Obviously this treatment cannot be regarded as a cure for silicosis, since it cannot restore lung tissue which has undergone fibrotic change; but Crombie and his colleagues believe that the inhalation of finely particulate aluminum powder offers every prospect of preventing the development of human silicosis.In view of these findings, it is surprising that repeated papers by Goralewski from Germany describe various types of lung disease attributed to aluminum dust, and press for them to be scheduled under the Workmen's Compensation Act in that country. Seven hundred workers were investigated. They were making, probably by a stamping process, aluminium powder containing about four milliards of particles of dust per grain, and are reported as complaining of dry cough with pain on breathing, shortness of breath, poor appetite, and gnawing abdominal pain. Spontaneous pneumothorax developed in four workers. No abnormal physical...

Jan 1, 1945

Determination of Porosity and its Influence on Specific Surface

Sep 13, 2010

The extra information brought by further drilling may seem necessary to achieve control over block grades if elementary estimation techniques are used. However a geostatistical study of an Australian deposit shows that better estimation techniques at the end of the first drilling campaign are sufficient to achieve required control.Subsequent drilling would be essentially wasteful.

Jan 1, 1975

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

By J P. Clark

Industrial minerals contribute about 50% of the NZ$1.2 billion generated annually by the minerals industry in New Zealand. The value is supplemented by a further NZ$500 million of minerals imported to supply our vital agricultural and industrial activity. As globalisation of the world's economy precedes, sources of minerals are being processed by fewer companies giving an ever-increasing control over global markets. If only to protect its primary production New Zealand needs to aggressively develop its mineral resources. The successful development of a deposit requires identification of the preferred market. While low-value aggregates dominate New Zealand industrial mineral production it is more specialised minerals supplied to the manufacturing and industrial sectors that provide more value per tonne. Minerals that have highly desirable intrinsic properties, or through value-added processing provide desirable properties, have the ability to fill niche markets both locally and overseas. Research and development towards enhancement or creation of desirable mineral properties could benefit New Zealand with both increased mineral potential and export of technological information. But, it is nearly always the market not the resource that dictates the viability of an industrial mineral and, with the globalisation of industrial mineral markets resulting in fewer but larger companies, any supplier must be ready to explore niche markets in order to compete on a more global basis.

Jan 1, 2000

Copper Extraction from Scrap Cables by Biotechnological Means

Sep 13, 2010

This paper examines the issues involved in the technical audit and valuation of exploration prospects. Certain methodologies are more appropriate to use depending upon whether the mineral property valuation is of an exploration area, a project under development, or an operating mine. Valuation approaches that are reviewed include the Multiple of Exploration Expenditure, Joint Venture Terms, Rules of Thumb, and particularly the Kilburn Rating Method. The DCF/NPV Financial Simulation Method, even modified by the use of Expected Values, is not considered appropriate for valuing exploration prospects. The choice of the most appropriate methodology and its successful application depends primarily upon the amount of reliable input data available and, more importantly, the experience and judgement of the valuer. It must be remembered that all valuations are time and circumstance specific and will be generally subject to revision as more data becomes available.

Jan 1, 1993

The Winton Basin is one of three Southland sub-basins. The oldest known sediments are Early Oligocene terrestrial shales, sands and lignites deposited in half grabens formed as a result of oblique extension. A marine transgression in the Oligocene deposited mid-outer shelf to upper bathyal mudstones. Shallowing of the basin and tectonic quiessence lead to limestone deposition in the Early Miocene. Regional tilting led to uplift in the north and east and deposition of terrestrial lignites and gravels across the basin and the basement high to the south.

Jan 1, 1992

Pressing-Drill Method - A Representative Method for Taking Analysis Samples from Recycled Materials

Sep 13, 2010

By A Rozendaal

Namakwa Sands, a heavy minerals beneficiation business situated along the west coast of South Africa, is a major producer of titanium slag, pig iron, ceramics quality zircon and rutile concentrate to the international export market. The bulk of the economic mineralisation, which includes zircon, rutile, ilmenite and leucoxene is hosted by a late Cainozoic aeolian succession overlying remnant palaeo-strandline sediments. Relatively younger duricrust layers that cement a significant part of the generally unconsolidated ore compounds the challenging processing character of the primary mineralogy. The complex nature and hardness of the duricrust ore influence their mineability negatively, and can potentially destabilise downstream ore preparation processes. Effectively, up to ten per cent of the entire mineral resource is sterilised as the present infrastructure is not geared to treat the hard-mineralised ore. The metallurgical performance of the primary processing stage, which entails wet density separation, is strongly a function of the quality of the heavy mineral assemblage, liberation state of the economic minerals and slimes content. Elevated concentrations of garnet, a gangue contaminant exhibiting similar physical characteristics as the economic minerals, subtract substantially from the recovery performance of the secondary concentration process, which comprises mainly wet magnetic separation. By contrast, the intrinsic mineral purity of the economic fraction governs its successful recovery to saleable products as stringent product quality specifications apply. Improved mine planning through geometallurgical enhancement of the existing mineral resource model is envisaged to benefit the entire Namakwa SandsÆ mineral beneficiation chain, ultimately aiming to optimise mineral resource utilisation.

Jan 1, 2008

Alkaline leaching with sodium carbonate solution adjusted to pH 9·5 to 10·0 preferentially dissolves thorium from a mixture of rare earth and thorium hydroxides. Rare earth sodium carbonates form in the alkaline leaching stage.These are converted to rare earth oxides for use as optical and ophthalmic polishing agents. Quadrivalent cerium is extracted under similar alkaline leaching conditions.INTRODUCTIONAustralia has made significant contributions to mineral chemistry and mineral dressing. As often happens with an industrially immature country, research investigations often outstrip the ability or desire of commerce to exploit them. It is wrong to think exclusively in terms of export of raw materials. Imagination assists in developing world trends. The chemical utilization of mineral sands has interested a group of investigators, chiefly at the Commonwealth Scientific and Industrial Research Organization (C.S.I.R.O.) and, more recently, in the mining industry itself. From an international point of view the highlight of this work was Newnham's (1960) process for the separation of hafnium from zirconium. Earlier work at C.S.I.R.O. investigated the chlorination of rutile, zircon, and monazite. Assuming that titanium tetrachloride would be available in large quantities in the post war years, extensive work was done by Kraitzer, McTaggart, and Winter (1948) on organic compounds of titanium. This work led to the development of heat resistant paints, plastic compositions, and improved organic protective coatings that predated overseas work by up to seven years. (Post, Shiihara and Schwartz, 1961; Anon, 1955). Contributions were made to the production of refractory hard metals (Kraitzer, 1949; Kraitzer and Newnham, 1956). Pilkington and Wylie (1947) and Urie (1947) investigated the production of rare earths from monazite by an acid process.

Jan 1, 1963

By K Gordon

A methodology for assessment and remediation of acid mine drainage (AMD) developed at the Sullivan Mine in the West Coast Region has been applied to the closed Blackball Mine, Blackball, West Coast Region. AMD from the Blackball Mine has low pH, high acidity, and elevated levels of iron, aluminium, manganese, nickel, zinc and arsenic. The AMD flows at a variable rate (36 - 101 L/s) into adjacent Ford Creek, causing an increase in acidity and trace element concentrations in the creek. To test the effectiveness of treatment with a simple limestone-based treatment system, a column leaching experiment was conducted over a nine day period. The results show effective removal of acidity, reduction in the concentrations of iron, aluminium, manganese and zinc, and production of alkalinity. To determine if this treatment method reduces the toxicity of the AMD to aquatic invertebrates, a 96 hour ecotoxicity experiment was conducted. The results show a significant decrease in mortality in the treated AMD compared to untreated. The column experiment, in conjunction with the ecotoxicity work, suggest that a passive treatment system consisting of a limestone leaching bed and an open limestone channel may be sufficient to treat the AMD from the Blackball Mine. Further work, such as large-scale treatment trials, is recommended.

Jan 1, 2004

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

In the estimation of reserves the known values of the variables of interest from surrounding drill holes are used to compute or estimate the unknown value of the orebody over a given region or at a given point of interest. The classical means of doing this are: 1. The Polygonal Method û where the region is divided into polygons centred on bore holes, each variable is then assumed to have constant value over each polygon. 2. Inverse distance methods, where the variable is assumed to vary linearly with the distance between the known values of the drill holes. 3. Inverse distance squared method û a quadratic variation is assumed for the variables between the bore holes.

Jan 1, 1983