Search Documents

The Wainui Mill was conceived as a 60 - 90 t/d central mill to process gold ores of the Thames area of New Zealand from small mines in the district. The ores of the region exhibit various degrees of refractory response to conventional cyanidation leach due to the fineness of the gold, and association with pyrite. The alternative circuits involving cyanidation, flotation, and possible small-scale smelting are examined. The environmental impacts have been audited by the Commission for the Environment and were found to be acceptable.

Jan 1, 1986

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (<1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G H. Clark

Batu Hijau is a porphyry copper-gold deposit located onSumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54 000 m of drilling in 105 diamond drill holes over a surface area of 1.2 km2 and to a depth of 1000 m below surface (412 m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55 g/t Au (variable cut-off) from an open pit in the higher grade portion of the resource.   The deposit is associated with a calc-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200 m diameter at surface to 500 m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbledykes or postmineralisation intrusive rocks.   Hydrothermal alteration of Old Tonalite and adjacent rocks is centred on the Old Tonalite and is zoned from a core of pervasive potassic alteration grading to an outer propylitic halo. At depth a propylitic assemblage is developed in the low grade core in the Old Tonalite. Phyllic alteration, late stage and mainly fracture controlled, overprints both potassic and inner propylytic zones. Intermediate argillic alteration overprinting is widespread, particularly on the eastern side of the hydrothermal system, where advanced argillic alteration overlies argillic alteration.   Ore grade mineralisation is cylindrical in shape, up to 800 m in diameter, and is centred on the Old Tonalite. A high grade shell (>0.75% Cu) forms an upward tapering cone in and around the Old Tonalite and reaches the surface in the centre of the deposit. Lower in the shell >l g/t Au and >2 g/t Ag accompany >1% Cu. Below 75 m above sea level mineralisation in the Old Tonalite rapidly decreases as a weakly mineralised core develops, but the limb continues to contain mineralisation to at least 412 m below sea level. Fracture and vein-controlled chalcopyrite and bornite are the dominant hypogene copper minerals and are the hosts for most of the gold mineralisation. Gold occurs free and in the lattice of the copper sulphides, and has been observed in quartz.   Weathering, especially where argillic alteration is developed, has produced a strongly leached cap, up to 147 m thick, below which is an irregular copper enriched supergene zone. Where leaching is not developed, such as over the centre of the deposit, an irregular oxide zone and a weakly developed supergene zone may be present.

Jan 1, 1995

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By D David

Clearly a plant designed only to treat average ore at the nameplate rate will fail to achieve nameplate in any typical year. To insert the necessary capability to achieve nameplate it is common process engineering design practice that plant must be able to treat an ore with 80th percentile value (hardness or competence values for example) at the nameplate rate. In the authorÆs experience, apart from a couple of notable cases, this has been applied reasonably well as a principal, and with widespread success. However, in a number of recent instances it became clear that the use of the 80th percentile number would have resulted in significant under design of the plant. This paper makes the case that the 80th percentile, as a principal, has can have serious flaws and its use needs to be assessed on a case by case basis. The discussion in this paper is the first step in developing a new design principal, and the associated methodology for selection of a design value, that will ensure plants are designed to achieve their nameplate capacities.CITATION:David, D, 2013. Is an 80th percentile design point logical?, in Proceedings MetPlant 2013 , pp 6-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Grade control is a real challenge, and better sampling and modelling practices are among the tools that have proven efficient in improving it. Although based on rather trivial examples, this paper addresses the following important issues: How much of a challenge is it? How and to which degree can it be improved? And what kind of economic benefits should be expected in return for the corresponding efforts?

Jan 1, 1999

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Economic Sustainable Power for Mineral Processing

Sep 13, 2010

By J Nixon

I have to say that my story is not too much different to many others who grew up and worked in the great mining fields like Broken Hill, Mt Isa, Rosebery, Kalgoorlie or Kambalda and any one of them could have stood up here and spun you a good yarn.What does my paper offer you in this volume? By sharing my experiences I want to encourage you to consider your own experience with leadership, taking on change, learning from and contributing to the development of others.I have been very fortunate to be part of many new innovations into underground mining over the past 40 or so years; most of it with Conzinc Rio Tinto Australia (CRA)/Rio Tinto operations.•From hand-held drills and a homemade single boom Jumbo mounted on an old Airtrak, to the sophisticated twin boom jumbos with high speed drifters all controlled by an on-board computer;•from a Scraper winch and a Wagner 2D loader to fully automated electric LHDs that navigate to the tipple, empty the bucket and return to where they come from;•from hand-held cut-and-fill and timber stoping in Broken Hill to the bulk mining methods of a block cave where at Northparkes we mined more ore in a month than we mined in the total five years of operations at Currawang;•from hand-held scaling and bolting with no skin protection to installing ground support with Jumbos and sophisticated Cable Bolters and the introduction of in cycle shotcrete;•from hand-held ladder rising and shaft sinking to Box Hole rigs, Raise Bore Machines and Blind Hole shaft sinking; and•from Gelignite based AN60 stick explosives, ANFO, fuse firing and half second detonators to Powergel, Emulsions and electronic computer programmed detonators that can somehow be initiated by ‘Blast Ped’ travelling through the rock.

Mar 21, 2011

By J S-L Chan, J C. T Chu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. In its industrial days, Hong Kong’s mining industry was thriving, benefitting from the mineral occurrences that are related to the regional Mesozoic igneous and hydrothermal activities.Hong Kong was unique in the mining sector as it was so small in landmass but with such a rich variety of commodities discovered. There are records of commercial exploitation of tungsten, iron, lead, silver, beryl, graphite, quartz, feldspar and kaolin in Hong Kong before 1981. Of these, most of them are located in the New Territories.The Lin Ma Hang lead mine was operated in the 19th century by the Portuguese and was abandoned in 1958. The Needle Hill tungsten deposit was discovered in 1935 during construction of the Jubilee Reservoir. The Ma On Shan iron mine, which operated for 70 years between 1906 and 1976, was the largest mine in the history of Hong Kong. The Mui Wo lead-silver mine on Lantau Island can be traced back to the Ming Dynasty 400 years ago. West Brother Island, which extracted graphite from 1952 to 1973, was levelled in the 1990s to make way for the development of the airport at Chek Lap Kok.Nowadays, these mines are disused and abandoned, but this extended abstract reviews the legacy of the mining industry in Hong Kong to understand the impact that it had on techniques, the economy and culture.CITATION:Chu, J C T and Chan, J S-L, 2015. The history of mining in Hong Kong , in Proceedings PACRIM 2015 Congress, pp 109–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Ramezani, K Faure, N Mortimer

Western New Zealand can be regarded as a rifted continuation of eastern Australia. Detailed studies of units previously considered to have trans-Tasman correlations are being undertaken within the FRST Programme Mineral Wealth of NZ and its EEZ to test specific connections, and thus add to the exploration framework of NZ. Correlation of two major episodes of granitic magmatism are currently being investigated. These represent the oldest (mid Paleozoic) and youngest (Early Cretaceous) magmatic events that conjoined Australia and New Zealand are believed to have in common.

Jan 1, 2007

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By M E. Taulis, S Hayton, D A. Manhire, J G. Pope

Successful development of coal seam gas (CSG) resources in low-rank coalfields such as the Powder River Basin has raised interest in CSG from low rank coal in New Zealand. Kenham Holdings Limited holds 12 Petroleum Exploration Permits (PEP) covering some of New ZealandÆs low-rank coal and lignite resources and has engaged CRL Energy Limited to assist in the systematic evaluation of the CSG potential of the permits. To date, exploration results from seven New Zealand coalfields reflect differences in coal type, rank, depositional environment and depth of burial between coalfields. Several of the explored coalfields are considered prospective for CSG. One of the most advanced Kenham exploration programmes is in the Hawkdun Coalfield, Central Otago.   The Hawkdun Coalfield contains a single, thick lignite seam with properties that are similar to the Powder River Basin. Preliminary results indicate the Hawkdun Coalfield is prospective for CSG with the potential to contain between 25 and 60 PJ of gas; enough to supply a 30MW power station for ten to 25 years. Further drilling is planned to investigate the economic viability of the Hawkdun Coalfield. The in situ permeability of the lignite, the amount and availability of free gas, gas saturation at depth and market opportunities will determine its economic viability. If initial pumping and production results in the planned exploration programme are promising, the Hawkdun Coalfield will be further developed with additional production drillholes to form a trial production pod.

Jan 1, 2004

The New Zealand microcontinent is relatively well endowed with gold deposits; its past gold production per unit area of 3.2 kg/km2 ranks high on a world scale. Total recorded production (1857 - 1986) is about 854 000 kg and most of this gold was mined between 1861 and 1920. There has been a strong revival in gold exploration and mining since 1979, with exploration expenditure of around $15 million per annum and a declared gold production in 1986 of 1265 kg (886 kg in 1985). In addition to numerous alluvial gold recovery plants working small to medium sized deposits (mainly in Westland and Otago), there are five medium to large projects that have started production (Martha Hill), or have reached advanced stages of construction (Grey River dredge), permitting (Golden Cross and Macraes) or exploration (Globe-Progress). This summary paper is taken from reviews by Brathwaite et al (1986) and Brathwaite (1988).

Jan 1, 1988

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

An Ammonia Leaching-Solvent Extraction-Electrowinning-Flotation Process for Copper Oxidised Ore Treatment

Sep 13, 2010

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017