Search Documents

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

By N. A. Tiner, Saara Asunmaa

The early stages of nucleation of vacuunz-deposited gold coatings on electropolished surfaces of pure nickel and binary alloys of Ni-A1 and Ni-Ti have been studied, employing carefully controlled temperature and vacuum conditions. The preferential nucleation of gold on slip-plane edges on the crystal surfaces gave rise to a very pronounced decoration effect which was used in studying the morphology of the pain boundaries, etch pits, and slip planes on crystal faces. Characteristic surface patterns were observed with local dimensional variations. Most pronounced geometric patterns were ohserved in the pain boundaries of nickel and on the crystal faces of Ni-A1 alloy. The nucleation behauior of gold indicates contamination on the Ni-T1 alloy and the getter properties of titanium are presented as a tentative interpretation for the detected contamination. The markings and imperfections on cleavage surfaces of crystals have long been observed by optical microscopy.1,2 Surface-replica techniques are also used to detect the smallest steps and structural details on crystal surfaces by electron microscopy. Recently, Bassett3-5 and Sella, Conjeaud, and Trillat 6 have shown that, when gold is deposited onto a rocksalt cleavage surface, there is preferential nucleation at steps and slip-plane edges on the crystal surface. This gives rise to a very pronounced decoration effect which is invaluable for revealing the lattice steps on a cleavage surface. According to Bassett,3 gold atoms arriving during vacuum evaporation at the crystal surface have a certain mobility on the surface after arrival, particularly at elevated temperature. If a significant

Jan 1, 1964

By A. H. Tousley

The cement industry is on the horns of an economic dilemma. Within the last ten years, its over- capacity in the United States has varied from 139- 127% of demand (Fig. 1). The most direct effect of this is seen in cement prices, which reached a peak in 1960, retreated steadily through 1966 and only recently climbed back to the 1960 level again. With prices in a slump and production costs estimated to be up almost 30%, there has been a steady drain on cement profits. Since 1960, labor costs have increased 86% while fuel costs have risen 18%. Meanwhile, customer service costs have also soared owing to the competition for cement customers and the wider variety of available cement products. This search for sales advantage has in turn led to a higher Blaine number, which means more grinding and hence bigger mills, more power, and, once again, higher costs. New plants as well as expansions and revisions to existing plants are also costing more owing to higher

Jan 1, 1971

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By G. H. Clevenger

THE reagents now used in flotation consist of various acids or salts, which may be either electrolytes or non-electrolytes, dissolved in water and some substance or combination of substances which function as collecting or frothing agents. At times the only dissolved salts present are those naturally occurring in the water used. The general effect of the electrolyte is to greatly sharpen the separation between the gangue and the concentrate. Examples of this are: The use of sulphuric acid with zinc ores; and of sodium carbonate or calcium oxide (line) with silver-gold ores. Crude pyroligneous acid is also sometimes used when available. Various oxidizing agents, such as permanganates, bichromates, etc., are added in the selective flotation of lead-zinc ores. Many other reagents for performing certain specific functions, either real or imaginary, have been proposed, and a number of them have been tried upon a working scale. The wild orgy of experimentation which is now going on in flotation exceeds even that which followed the introduction of the Washoe process for the treatment of Comstock ores, when, among other things, sage-brush tea and tobacco juice were reagents added to the pans. Out of all this will, of course, eventually come a more or less standard practice for the treatment of each class of ore. Omitting a discussion of the functions of frothing and collecting agents, the reagents used in flotation for this purpose may be classified under five general heads: (1) Essential oils; (2) fixed or fatty oils;. (3) alcohols and their combinations with organic acids; (4) coal tar and its refined products; (5) petroleum and its refined products. A flotative agent of some kind is required in flotation as now practiced. A single reagent, as, for example, certain. of the essential oils, may perform the dual function of frothing and collecting agent, or a mixture of substances may be required.

Jan 9, 1916

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971

By W. B. Coleman

Considerable discussion on the effect of iron and steel scrap in blastfurnace burdens was presented in the January, 1927, issue of Mining and Metallurgy. Therein the question is asked as to what causes the difference in physical properties of pig irons where the chemical analyses are practically the same. This point no doubt has been noticed by a number of furnace operators, but several years ago very little thought was given to it. The foundries purchased pig iron, had it analyzed and found it to be within their specification. The castings made from this iron at times would be satisfactory and at other times hardness and shrinkage would occur. Since the iron was chemically correct the foundries generally were at a loss as to what to do. They changed their method of melting in the cupola and in some cases this corrected the trouble. In some instances the foundry would continue eliminating a brand of iron until the castings produced were satisfactory. Through this process of elimination they would finally arrive at the conclusion that a certain brand of iron was causing the trouble. During the course of this elimination minor changes might have been made in the melting and in the end satisfactory castings were secured without discovering any definite reason for the trouble. Frequently the foundries blamed the manufacturer of the pig iron although the seat of the trouble was in their own method of melting. I have in mind one foundry in particular that was using three brands of pig iron for producing their castings and their losses were rather high. Three entirely new brands of iron were substituted in the charge and still the losses continued. Even after using six brands of pig iron the management felt that the pig iron was the cause. The difficulties encountered in the melting of iron in the cupola, over the past several years, reflect in a great many cases on the operation of the cupola. At different times certain brands of iron were unsuitable for producing a certain class of castings, but at the same time one could see no reason why the iron should be considered abnormal. Irons from furnaces where production and low cost are the main factors that are being used in foundries produce in most cases harder cast-

Jan 1, 1927

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

THE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently attempted to make a much too simple correlation between mineral discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail

Jan 1, 1941

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price 'tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

INTRODUCTION It has been impossible for the student, the practicing engineer, and the geologist to find all of the essential elements of mineral appraisal and mineral economic analysis in a single text. Indeed, the most recent texts on mine evaluation are over 20 years old. Many of the basic principles of mine sampling and evaluation have not changed over the ensuing years, but with the advent of the digital computer the entire scope of mineral evaluation has been expanded to encompass superior techniques that heretofore were not possible when using manual methods. The old manual methods for ore reserve computations and the techniques for assignment of area of influence to drill-hole samples are now as antiquated as the Model-T Ford. With the computer making possible solutions that had not been practicable in terms of time and effort, it is important for the practicing explorationist and mining engineer to understand many of the new concepts and principles that can be applied with the resolving power of the computer. Many practicing mineral industry professionals have been disappointed by certain computer programs and thus have some reservations about computers being able to solve their very real problems. Often the gap between the practicing engineer and the ivory tower theoretician applying modern computer techniques is too broad to be bridged with scattered, fragmented publications. PURPOSE AND SCOPE OF TEXT It is the intent of this book to update and to unify a great many scattered reference works used in the mineral industry today. The ensuing pages are addressed both to the professional already working in the mineral industry who needs information on computerized methods as well as to the serious student seeking to grasp the fundamentals and modern techniques of mineral appraisal and feasibility. These techniques are based on sound mathematical principles and theory, with the computer as a tool-but a very essential tool-for the solution of the problems involved. The computer can be of value only if it is programmed by those having sufficient expertise to use its inherent problem-solving capability, and the output is interpreted by those who are sufficiently acquainted with its operation to understand the data it produces. In the pages that follow the author intends to outline in considerable detail all the essen-

Jan 1, 1980

By L. A. Delano

During 1916, the St. Joseph Lead Co. milled 2,505,670 tons of ore. This is a daily operating average of 7855 tons. The economic concentration of such a large tonnage necessarily requires a plant equipped with modern machinery and operated efficiently. The milling process used in producing this output has been a gradual development through the long period of years that the company has been in existence. HISTORICAL SUMMARY OF MILLING PRACTICE Ore was first mined at Bonne Terre, Mo., in 1864. The early milling practice was crude. It consisted of breaking the ore into small pieces by hand, pulverizing in a Blake crusher and a pair of Cornish rolls to approximately minus 6 mm., and jigging in the old-fashioned hand jigs. Only the coarse heavy galena was saved, the gangue being shoveled off and discarded. The output for the first year under this method was only 240 tons of pig lead. The first mill of the company was a combination of extensions and additions built from time to time as the mines developed. It was a museum of early milling machinery, such as jigs, percussion tables, buddies, dolly tubs, log washers, etc., following no definite flow sheet. The chats, or tailings, were hauled to waste dumps by mule and ox teams, as much as 500 tons per day being moved in this manner, until a railroad was built in 1880. This mill was burned in 1883, at which time the annual output had reached approximately 7300 tons of pig lead. A new mill of 500 tons capacity was designed and built by C. B. Parsons. This mill has been admirably described by H. S. Munroe.' The ore was crushed in Blake crushers, Cornish rolls, through 6-mm. screens, and treated by jigs of the Parsons type, percussion tables and log washers, or trunking machines, for cleaning the galena. The middlings were recrushed in rolls and treated on Harz jigs. The mill was operated without change, except later installing Gates crushers and en-

Jan 1, 1918

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By H. F. Yancey

AT the annual meeting of this Institute held two years ago a new method, of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a resume of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed-the C.I.T. roll-test method4.

Jan 1, 1936

By Joseph F. Shirley

A froth flotation plant to recover byproduct molybdenite must be designed specifically for the selected separation process and the type of ore being treated. However, some general rules concerning byproduct molybdenite plant design can be suggested that would be valid for most processes. The term byproduct molybdenite in this paper is limited to the recovery of molybdenite from copper porphyry ores, which essentially amounts to selectively separating molybdenite from copper and iron sulfide concentrates. In addition, most of the discussions would apply only to the almost universally used approach of floating the molybdenite and depressing the copper and iron sulfide minerals. Thickener It is considered essential that the feed to a byproduct molybdenite plant be thickened prior to being treated for molybdenite recovery for the following reasons: 1) Thickening allows the rougher and any preconditioning stages to be operated consistently at the optimum percent solids. 2) Generally, the size of equipment used for pretreatment and the rougher flotation is considerably smaller and less expensive than if the copper flotation concentrates were treated directly. 3) The removal of as much water as practical by thickening removes flotation reagents added in the copper flotation circuit, especially frother which can be quite troublesome in a byproduct molybdenite plant. Although thickening of the molybdenite plant feed has long been recognized as necessary to optimum metallurigcal results, very often this area has been designed poorly. The thickener should be sized so that it can produce a consistent thickened product containing 60 to 65% solids without the use of flocculants. Some plants are only able to thicken to 45 to 50% solids consistently while other plants let the percent solids vary from 45 to 60% over a 24-hr period. While the former is more desirable than the latter, in many cases better metallurgical results could be obtained if the percent solids could be held consistently close to 60%. Probably the simplest and most satisfactory system of handling the thickener underflow is to spigot it into a sump, using a sphincter type valve for the orifice, controlled by a density meter. Another satisfactory approach is to use an ODS type pump to meter the underflow. There are other methods of handling thickener underflow which work satisfactorily as long as the amount of copper concentrates entering the thickener is relatively uniform. However, they often fail to operate satisfactorily when there are large fluctuations in the thickener feed rate due to fluctuations in ore tonnage and/or copper grade. If the percent solids in the plant feed could be held close to 65%. There is the possibility the molybdenite plant tailing would not have to be thickened prior to the copper filter plant. This means that the molybdenite rougher float would have to be conducted at 45 to 50% solids with all the cleaner tailings returned to the rougher for dilution. Admittedly, in some situations this approach would be impossible, but if capital or plant area is limited, it should be considered.

Jan 1, 1981

By G. K. Burgess

(New York Meeting, October, 1913.) 1. COOLING AND HEATING CURVES BY G. V. BURGESS AND J. J. CROWE. § 22. THE results published in Professor Howe's paper 10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels 11 containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by' the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to -0.1 sec. for recording .time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12. The observations were taken in vacuo on cylinders 5/8 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thereto-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by, platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 6, 1913