Search Documents

By Ellsworth Daggett

The ore smelted in the Winnamuck furnace during the year 1872 consisted, for the most part, of oxidized ores from the Winnamuck mine, only sixty tons of outside ore (from the Spanish mine) having been smelted. The latter, like the principal Winnamuck ore, was oxidized or so-called carbonate ore. There was mixed with these oxidized ores three hundred to four hundred tons, or 7 to 10 per cent. of galena, some of which was mined with the oxidized ore, while a part was mined separately from the lower portion of the mine, and afterwards mixed with the ore, with a view of preventing the formation of deposits of metallic iron in the furnaces. The average assay in silver of all the ore handled was 51.46 oz. per ton, most of it existing as chloride of silver. The lead contents were 34.98 per cent,, all, or nearly all, in the form of carbonate of lead. The relative amount of silver is not at all constant, the best silver ore often being poorest in lead. The predominant gangue was silica, several determinations of which have been made on representative samples, yielding in three such samples 26, 38, and 58 per cent. silica, the latter test being ore containing but little lead. The average contents in silica are about 35 per cent., with 6 to 7 per cent. sesquioxide of iron, and small quantities of alumina and lime. Mechanically, the ore was very fine, and so thoroughly disintegrated that it presented few distinguishing characteristics, rendering sorting or separating of ore from waste difficult, and often impracticable. Experiments on a small scale have been tried, with a view to separate the silica by washing; but these were unsuccessful, as the finest slime, requiring a long time to settle in still water, contained a large amount of silver; and on a careful sizing and washing of the sands and coarser parts, the silver contents were found to be less dependent upon specific gravity

By R. J. Mechin

Top-slicing was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent of the Santa Gertmdis mine. There then existed 1200 ft. below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 354.2 ft.) a block of ore having a length of 295 ft. and an average width of 82 ft. and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing. Description of Block of Ore Former operators, when mining the original vein, left in the foot wall ore of too low grade to be profitable at the time; also, considerabe low-grade material was sorted out and stored as filling in the stopes. Some pillars were left in place, either for support or because they were not payable. All this has formed a body of ore that can now be exploited

Jan 1, 1925

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By AIME AIME

WEDNESDAY night, by long tradition, is al- ways set aside for the annual dinner, even when, as it was this year, it is Ash Wednesday. Whether the somewhat smaller attendance than last year is attributable to that cause, the unexpectedly long persistence of business depression, or whatever may have been the reason, it was a joyous occasion, and the grand ball-room of the Commodore Hotel was as completely filled With diners as * was consistent with com- fort. In the half hour before the dinner was actually served the guests assembled in an adjoining room and not only exchanged greetings but proceeded along the receiving line to greet the guests of honor. The number present was so large that hardly more than half of them had been able to do this before the summons to the dining room sounded and a hearty and immediate response was made to it. Toy balloons at each plate, inflated and directed at the heads of companions or nearby friends, but which were just as likely to carom from the nose of a hurrying waiter, successfully broke the ice as well as not a few plates. It would be interesting to know whether the pleasure the guests derive from these de- vices is in part based on the all-too evident annoyance of the waiters, and what the relative quantitative relationships are.

Jan 1, 1931

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929

Jan 1, 1880

By MALCOLM FRASER

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably linked with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Australia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining industry brings Australia will continue to be enormous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry. In the past year there have been positive signs of a resurgence in exploration and development. The North-West Shelf ventures are spending $50 million on a feasibility study to work out the extent of future investment in that project; exploration expenditure for minerals other than petroleum increased by 34 per cent in 1976-77 to $134 million; petroleum exploration increased dramatically last year almost doubling to $94 million-this year it is projected to reach $125 million.

Jan 1, 1978

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By Wayne E. Tuomi

The mining industry is faced with a pressing problem; that is, to develop more efficient methods of extraction, handling and upgrading-techniques that will do the job faster and better than ever before. New techniques require new machines, or applications of new and improved materials that can be used to modify and improve existing machine and equipment designs. The traditional approach has been to increase productivity by increasing equipment size. Prognostication indicates that the trend toward larger equipment sizes and capacities will continue as one answer to the challenge imposed by future increases in mineral demands. But what is the limit on the continued growth of equipment size? Until about 1930, there was a very definite limit-a limit imposed by the strength of the steels and the power plants then available. The equipment engineer had come to an impasse: even though it was easily possible, for instance, to triple the size of a bucket, it had become impractical to correspondingly enlarge the boom, the counterweight, and the power plant.

Jan 3, 1967

By Nestor Torres-Acuña, Fathi Habashi

Metallic copper of purity equal to commercial electrolytic copper is deposited during the anodic dissolution of technically available white metal, Cu2S, in m acidic solution of' copper(II) sulfate as electrolyte and copper sheets as cathodes. The process may be applied on commercial scale since it has the advantage of by passing the converting and poling steps, decreasing pollution problems due to SO, and recovering the sulfur of the white metal in the elemental form. The anodic dissolution is believed to take place in three steps: The working conditions that lead to 98 pct cathodic current efficiency are: 30 gpl Cu2+ and 100 gpl H2SO4 in electrolyte, current density 1.0 amp per sq dm, and tetnperature of bath 40°C'. DURING the smelting of copper, nickel, lead, and zinc sulfide ores, large amounts of sulfur dioxide are produced. Because the release of this gas in the atmosphere causes pollution problems, many attempts were made in the past for its recovery either in liquified form or processed to sulfuric acid. Although these two forms of sulfur are the usual forms that are consumed by the chemical and metallurgical industries, their storage and transport usually raise economic problems. It was realized, long ago, that a process by which sulfur can be recovered directly in the elemental form would be most attractive. Elemental sulfur is easily stored and transported, and is readily converted to SO2, H2S, or H2SO4 when needed. Processes aimed to recover the metals from their sulfide ores, and at the same time by-product sulfur in the elemental form, were recently reviewed.' As early as 1882, Marchese2 patented a process in which a matte having the composition: Cu 15, Pb 14, Fe 41, and S 25 pct was electrolyzed. According to cohen3 the process was applied on a pilot scale by the Aktiengesellschaft fur Bergbau-, Blei-, und Zinkhiitten-betriebe at Stolberg, Rheinland, Germany. The process was unsuccessful, however, owing to the contamination of the electrolyte during electrolysis. Studies in this field were reported by Bernfeld4 and Egli.5 Borchers et a1.6-8 developed the process further by using white metal (Cu 78.2 pct, S 19.6 pct) instead of the matte, and a pilot plant was operated by the Mansfeldschen Kupferschiefer Co. at Eisleben, German~.~ It appears, however, that the process never went into commercial operation. Further studies in this direction were carried out by Russian workers.10-23 The International Nickel Co. of Canada erected a pilot plant at Port Colborne in 1951 to apply the process to nickel matte which is essentially pure nickel sulfide."'- 26 Full-scale plant went into operation at the Thompson Refinery in Manitoba in 1964.27 In this method nickel sulfide matte is melted and cast into anodes analyzing 76 pct Ni and 20 pct S with small amounts of copper, cobalt, and iron. These anodes are then electrolyzed in an aqueous solution of NiS04 at pH 4. Further work on this method was reported in the literature.28-31 In this paper, experiments on the anodic dissolution of white metal in aqueous copper sulfate solution are reported. EXPERIMENTAL White metal, Table I, obtained from The Anaconda Co., was cast in form of anodes 10 by 7.5 by 1 cm, Fig. 1. The anodes are mechanically strong and do not break easily; when polished they gave a shiny gray metallic appearance. From the chemical composition shown in Table I, it can be seen that the atomic ratio Cu:S corresponds approximately to the formula CU2.06S. The copper in excess to the formula Cu2S is most probably present as a separate phase since metallic copper could be seen under the microscope, Fig. 2. Fig. 3 shows the X-ray diffraction pattern of white metal which matches fairly well with that of reagent-grade Cu2S.

Jan 1, 1969

By R. W. Raymond

THIS meeting was held in the new home of the Institute, the United Engineering Society Building, 29 West 39th Street, New York City, directly following the Dedication ceremonies. The first session was held in the large Auditorium, Thursday, April 18. The meeting was called to order by Mr. John Hays Hammond, President of the Council, who said Before taking up the reading and discussion of papers, I will call upon Dr. Rossiter W. Raymond, the oldest living past-President of the Institute, who has been in harness almost continuously for thirty-six years, and who has contributed more than any one else to bring this society to its present great success and to establish the reputation of the American mining engineer the world over, for a few words supplementary to those which were uttered to engineers generally, during the sessions of yesterday and the day before. ADDRESS BY R. W. RAYMOND. The generally accepted Darwinian doctrine of the survival of the fittest is sometimes illustrated by persons who are supposed to be the fittest because they have simply survived. I fear that I come under that category. Almost all of my contemporaries in the early history of this Institute have passed away. Only one or two of the original founders remain, and I may fairly say that scarcely any remain who were active at that : time in shaping the organization and the future career of the Institute. In May, 1871, I was thirty-one years old. Next week I shall be sixty-seven years old. All the intervening years have been devoted to the service of this Institute almost continuously, either as President or Vice-President or Secretary. You may easily imagine, therefore, with what pleasure I greet you on this occasion. I am not here to extend to you the welcome of the City - of

May 1, 1907

Jan 1, 1889

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By John V. Beall

Let's start at the beginning, Mr. Turner. Where and when were you born? In Lansing, Mich., on July 31, 1880. And what was your education? I went to the University of Michigan, where I got an A.B. degree in 1902; then to the Michigan College of Mines at Houghton, graduating from there in 1904 with a B.S. and an E.M. What was your first job in the mining industry, Mr. Turner, and what were you paid? In the summer of 1902, 1 was a field assistant for the U. S. Geological Survey in southwestern Idaho and southeastern Oregon, working under Israel C. Russell, professor of geology at the University of Michigan, who incidentally, had just returned from an expedition to study the effects of the eruption of Mt. Pelee, on Martinique. I was paid $60 a month and found; in addition to doing geologic and hydrographic work, I cooked many of the meals for a party of four, and wrangled four horses. I slept for four months under the stars, without a tent.

Jan 1, 1949

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923