Search Documents

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Cristiano José Scheuer

Experiments were carried out aiming to study the influence of micro-abrasive wear test variables and plasma treatment parameters, on the tribological characteristics of low-temperature plasma carburized AISI 420 steel. The first part of this study was conducted in order to evaluate the influence of abrasive particle size, normal load and counter body rotation speed on carburized sample wear behavior; and the second part was conducted in order to evaluate the treatment temperature and time effect on carburized samples wear behavior. Plasma carburizing treatments were performed at 8 and 12 h, for temperatures ranging from 350 to 500°C; and at constant temperatures of 400°C for times between 12 to 48h, and for 450°C for times of 4 to 16h. Micro-abrasive wear test were performed by mean of a calowear ball-cratering equipment using a polished ball of AISI 52100 steel rotating at 80, 120 and 160 rpm, for sliding distances from 2.6 to 104.2 m. Alumina abrasive particles with sizes of 0.05, 0.3 and 1.0 ?m were employed. The normal loads applied on this study were 0.1, 0.3 and 0.5 N. Carburized sample was characterized by mean of OM, XRD and hardness measurements. Worn crater characteristics were evaluated by confocal laser microscopy. Results showed that the transient wear regime prevails along the outer layer length (composed by Fe3C and ?’C), and the steady-state wear stabilizes in the diffusion layer region (composed by ?’C). It was verified that the wear rate and wear coefficient decreases with treatment temperature in the range of 350–450°C and increase for 500°C. It was also verified that the wear rate and wear coefficient decreases with treatment time in the range of 12–36 h (for 400°C cycle) and 4–12 h (for 450°C cycle), and increase for larger treatment times due the chromium carbide precipitation. It was also found that the wear coefficient increases with the increase of abrasive particle size, and decrease with the increase in counter body rotation speed and normal load. Lastly, the analysis of the worn craters indicates the occurrence of grooving and micro-rolling abrasion wear mechanisms.

Aug 17, 2017

By Ryoma Fujiyoshi

In this article, the technologies of highly durable MgO-C bricks for the scrap impact zone and bottom blowing tuyere of converters are demonstrated. On the bases of our recent investigations, wear of scrap impact zone and bottom tuyere are explainable in terms of crack initiation and propagation. Theoretically, crack propagation in brittle material is regarded as generation of new crack surface area. It occurs when the elastic strain energy stored in the material exceeds the energy required to generate a new crack surface area. Since the overall energy consumed for crack propagation until fracture is evaluated by fracture energy, materials exhibiting high fracture energy can be regarded as materials with high fracture resistance. Therefore, two fracture energy-improving technologies for MgO-C bricks were developed. One is matrix reinforcement and the other is carbon bond enhancement. These technologies were applied to bricks for the scrap impact zone and bottom tuyere. As a result of commercial applications, notable decreases in wear rates were recognized for high fracture energy materials for the scrap impact zone and bottom blowing tuyere of converters.

Oct 30, 2017

By Andrea Zanon

Recently steel manufacturers have significantly focused their attention on safety and working conditions thanks to new labour laws, comprehensive operators’ knowledge and increased company social responsibility. Even with a reduced budget, investments on safety are now widely approved. Mill constructors aim at developing upgraded solutions to comply with these new requirements. In some cases mill constructors can even anticipate customers’ requests and consequently put into the market innovative solutions. In this text we will analyze some advanced solutions developed by Danieli & C. Officine Meccaniche Spa - the leading company in long-product rolling mills - aimed at improving working conditions on wire-rod block settings. In particular, we will focus on rolling guides installed on fast-finishing blocks and on servo-assisted device for rolling rings changing. In fact, this equipment has shown effective benefits on our test plants and has mainly cut out the tendency of the personnel to be absent due to backache. This paper will first present standard working conditions, will then introduce the newest equipment developed by Danieli & C. Officine Meccaniche Spa, will analyze its operation and finally will describe in detail the benefits that can be reached with its use.

Jul 30, 2018

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Claudio Fabbro

The increasing demand of wire rod high carbon grades for both small and large sizes are challenging the wire rod producers to enhance new technologies by combining high plant productivity and efficiency of superior quality finished products with extreme process flexibility. The possibility to change process route according to the final application of the rolled steel grade and to simplify production planning is one of the most important keys to success that distinguishes the mill plants developed by Danieli. This paper will focus on the most important metallurgical and process targets and on the in-line heat treatment technologies representing the core of Danieli know-how on high carbon grades production.

Jul 30, 2018

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Milan Terčelj, Matej Drobne, Urška Klančnik, Peter Fajfar

The study of oxidation behavior of High Chromium Steel material used for surface layer of work rolls was carried out. Specimens taken directly from the roll were subjected to thermal fatigue in the temperature range between room temperature and 500 °C up to 700 °C by using thermo-mechanical simulator Gleeble 1500D. Our observation was focused on the impact of oxidation as a principal mechanism of degradation of the roll’s surface layer - mainly on the characteristics of oxidation propagation in relation to the test temperature and microstructure constituents characteristics of the material. Oxidation is considerably accelerated by certain characteristics of eutectic and primary carbides, i.e. their size (area), composition, morphology, orientation regarding to the water-cooled surface, etc. In the presented paper selected cases where emphasized oxidation takes place are investigated, analyzed and explained. Obtained results thus represent a contribution to explanation of conditions which lead to acceleration of oxidation behavior that in turn can lead to chipping or even early spalling of material from the roll surface layer.

Oct 1, 2019

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By Francisco Morganti

In order to support hot rolling mill managers in improving the utilization of their plants, SMS group offers well defined Performance Modules. These are technologies, components, automation solutions or services, which can be implemented in existing plants to increase competitiveness in categories of efficiency, productivity, quality and process and product control referred to as “Industry 4.0”. Except the Performance Modules dedicated to the last category, targeting overall process controls, Performance Modules are characterized by quantifiable benefits. Performance Modules related to hot rolling mills are e.g. camber free rolling, modular laminar strip cooling system, new edge masking and intelligent components.

Oct 30, 2017

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By Yasser Ghobara

Phosphorus is a problematic impurity that has challenged steelmakers for decades. Steel producers have developed specific technologies to eliminate phosphorus prior to and during steelmaking. These process technologies reduce phosphorus to various degrees and increase the cost of making steel. The state-of-the art dephosphorization technologies are described and operating costs compared for each of the established technologies. Costs are discussed in terms of price penalties for high P iron ore and selling premiums for low P steel. From this, strategies to control P in a cost effective manner are described.

Aug 17, 2017

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Fabiano Soares

Strand guide rolls in continuous casters are crucial components for guaranteeing an optimum process for the production of high-quality steel grades. The properties of these rolls greatly influence the quality of the slab produced. The most commonly used designs so far have been the axle roll and the solid roll. A quite new roll concept is the STEC-Roll®. It combines the advantages of the axle roll with those of the solid roll. This paper explains the development of this roll type and shows the current design. The characteristics of the STEC-Roll® are presented in greater detail and are underlined by a number of simulation results. Beside the design itself, the benefits for casting and maintenance are explained, including for example the easy assembly and dismantling or the use of the roll for dry casting. A brief examination is made of the TCO for the STEC-Roll® and an estimation is provided of the exchangeability of this roll. To conclude, an overview on the current applications is presented.

Aug 17, 2017

By Daniel Augusto Godinho de Carvalho

Since the beginning of BOF process, slag formation has been subjected to extensive development. During the initial stages of the blow, fast slag formation is primordial for the process performance. This is mainly to allow oxidizing reactions, and also to protect the refractory. A modeling of BOF process for the purpose of process optimization requires precise knowledge concerning the dissolution of CaO and MgO based materials. Using this knowledge, the optimal process conditions can be ensured by a controlling of the slag formation during the converter steelmaking process. Taking into account an application of large amount of different raw materials, as well as location-specific process conditions, the characterization of the dissolution behavior of different additives is an important key to improve the technological process. Thereby, in the frames of this project, an appropriate model for slag formation is established and compared to operational results for a 330t BOF, operating at ThyssenKrupp CSA, Santa Cruz, Brazil.

Aug 16, 2017

By Andrea Codutti, Gianni Tiussi, Andrea Tonnicchi, Morris Codarin

Essar Algoma Steel, Canada, awarded Danieli Transimissions a strategic order for the upgrade of the main drive spindles belonging to the most loaded stands of the Hot Strip Mill, F1-F2, F5 and F6. Featuring special heavy duty design and advanced torque monitoring system, these spindles replace existing competitors’ grease lubricated design with the efficient continuous oil lubricated solution to withstand the tough working conditions, increase life expectations and provide room for a product mix extension. The first couple of spindles have been installed in September 2017 by the expert Service team and are showing already good and reliable performance. Progressively all the others are being installed.

Oct 1, 2019