Search Documents

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

BATMINÖ, BATMINEÖ, BATMINDÖ are an abbreviation for Business Analysis Tools for Mining, Mine Evaluation and Mine Design respectively. BATMINP are proprietary tools customised to suit individual client requirements. The first suite of tools provides for analysis and evaluation of open pit mining equipment alternatives and includes fleet selection, fleet sizing and production, productivity and economic outcomes. The models address all mine process activities including drilling, blasting, loading, hauling and auxiliary services. All models are built to provide for simultaneous evaluation of multiple alternatives that are time and condition related. Provision is made for modelling from first principles and/or default or shortcut inputs. Sensitivities to key input parameters are easily performed and consistent logic is applied throughout the process. The models are built to provide key outputs in a format suitable for presentation and documentation. Provision is also made in the models for validation of both inputs and outputs through benchmarking, back analysis and budget comparison. The same models can be used for short interval (12 month) planning and control, medium-term (three to five years) and long-term life-of-mine (LOM) planning. Millions of dollars are spent each year on mining plant and equipment. Decisions that impact on the medium and long-term are made. BATMINP tools have been used to perform studies with good results and in most cases the studies have been validated through back analysis and comparing model outcomes to real data.

Dec 6, 2010

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

The International Symposium-cum-Workshop on Management andControl of High Gas Emissions and Outbursts in Underground CoalMines was held in Wollongong in March 1995. Coverage of high gasemissions was virtually confined to instantaneous outburst implications, essentially seam gas pre-drainage. Globally, instantaneous outbursts have been known for 150 years, andthe first Australian outburst occurred in 1895 and Australian occurrences and mines affected have increased since. Few significant coal producing countries are unaffected. The coals affected range in rank from lignites to anthracites. Geological disturbances are the most likely environments for occurrences. The most likely mining geometry is of virgin headings, with some occurrences on longwalls and in other situations. Widespread research into many aspects of the problem has yet to produce a generally accepted explanation. Explosive inducement is a well-known control. Apparently high advance rates increase face gassiness and create higher stress abutments, increasing proneness. The most popular preventive measure, pre-drainage of virgin coal ahead of faces has produced highly successful very long hole drilling performances but without the precision necessary for accurate geometric hole patterns, despite quite sophisticated drilling equipment and hole surveying instruments. For the future, more precise degasification is sought, even from the surface, together with rapid face coal gassiness assessments to confirm lowering below threshold values, as well as other proneness lowering measures, perhaps related to new heading and longwall geometries and to new equipment to provide them. But above all, safe management plans are required for each operation, to safeguard the miners and their working environments, and thus to protect underground coal mining from this mounting threatening problem.

Jan 1, 1997

By Oliver Bowles

Lime is of tremendous importance to modern industries. In agriculture it is regarded as essential to the continued fertility of many important regions; in building it is indispensable, and in the many ramifications of the chemical industries it is so necessary and so widely employed that it has been designated "the king of all the bases." Figure 1 shows a general view of a modern lime plant producing more than 500 tons of lime daily. In 1924 the production of lime was reported from nearly every State in the Union and amounted to more than 4,000,000 tons, valued at, nearly $40,000,000. For a production of that magnitude between 8,000,000 and 9,000,000 tons of limestone are required. The many problems involved in winning this great quantity of raw material from the natural rock and preparing it for the kilns have in the past received little attention from any governmental agency. Therefore, in compliance with a request from representatives of the National Lime Association in 1922, the Bureau of Mines began a study of problems in limestone quarrying in an effort to advance more economical methods of operation and the utilization of waste material. Field studies were made at many quarries, and the information thus compiled, besides data already at hand from work in other branches of the stone industries, were disseminated to operators in the form of mimeographed Reports of Investigations, eight of which were issued at intervals during 1922, 1923, and 1924. A questionnaire was appended to each report, and quarry operators were invited to contribute additional information obtained as a result of their actual experience and observation. Operators of lime plants have been cordial in their responses and have supplied the bureau with much valuable information. From the data thus obtained, supplemented by later field studies, the revised reports have been combined to form the major part of this bulletin, which is believed fairly to represent present knowledge on the subject of quarrying limestone for lime manufacture.

Jan 1, 1927

By David L. Veith

This Bureau of Mines bibliography of U.S. and Canadian literature pertaining to revegetating coal-mined lands contains 805 references published from 1977 to 1984. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate only those dealing with the coal mining region and subject of interest. All references are annotated. Other sources of information are given, including Office of Surface Mining (OSM) and State reclamation agencies and other published bibliographies.

Jan 1, 1985

By John L. Kaplin

The underground construction for the Phase I Combined Sewer Overflow(CSO) Project is on an impressive scale by any measure, appearing more so in a midsize city like Providence, RI. The Narragansett Bay Commission recently completed $350 mil-lion in construction to improve the water quality in Narragansett Bay. This project included a number of serious challenges, delays, and disputes. Looking back on this complex project completed within budget, it is hard to consider the work as anything other than a success. Along the way, this outcome did not always appear certain.

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

By P. van der Veen

The objective of this paper is to analyze the evolution of the strategic drivers of the mining sec-tor over the last half century, which has been guided by a varying and expanding list of motivations. While companies cannot survive for long unless they are making profits, the strategic drivers of the industry have gone far beyond profits since at least the mid-1970s when environmental concerns began to be taken seriously. For the most part, these forces have followed global trends and public opinion, but they have been shaped and magnified by the significant, often dominant role that the mining sector plays in many economies. While the mining sector used to be primarily motivated by the first pillar of sustainable development -i.e. the economics pillar-, in the 1970s the second environmental pillar became an important factor in decision making, and in the 1990s the third social pillar emerged as a major driver.1 The entrance of new strategic drivers has also had considerable impact on technological and organizational developments in the mining industry; however, technological changes, driven by cost reduction considerations, have in turn impacted the strategic drivers of the industry, resulting in the need for further technological and organizational developments.

Jan 1, 2007

India is on fast economic growth. Even in the turbulent years of global crisis, it could achieve a growth of over eight per cent. In recent past, Indian Government has been contemplating a faster growth in all the sectors of economy so as to make the nation an economic power in the world.Steel is a versatile material. It has its role in most of the major industrial activities, such as infrastructure, automobiles, urbanisation, consumer durables and other. In other words, steel is a part and parcel of industrial expansion, urban and rural development. It is rightly admitted that steel acts as pillar of any development model. Volume of steel consumption is the barometer which measures economic progress and/or industrial status of any country.India and China are the two countries in Asia which have the significant impact on the global steel industry. Of course, China is much ahead of India in consumption level of steel.

Dec 6, 2010

By Patiño E

Bioleaching is an established technology for the pre-treatment of refractory gold ores and concentrates and the leaching of whole ore copper heaps. In many cases, it offers economic, environmental and technical advantages over pressure oxidation and roasting. However for bioleaching to compete successfully with others pre-treatment processes it needs to be optimized with regard to the parameters that affect the bioleaching reactions and the growth of the microorganism involved. In this sense, this paper focus on the thermodynamic approach applied in bioleaching through of the definition of the growth system and it is thermodynamics analysis, the effect of heat production and energy dissipation on growth and thermodynamic analysis of growth kinetics and the effect of nonstandard conditions.

Sep 12, 2005

By Michael Stuart Parsons

The haulage cycle is the sequence which a haulage vehicle must first arrive at the loading area, then turn around and reverse into position. Once it is loaded, the vehicle leaves and travels to the unloading area, where again it must turn around and back up to unload. The cycle is repeated over and over again. The Vector Neutral truck is a rubbertired, self-propelled hauling vehicle designed such that it eliminates the requirement to turn around and back-up to either load or unload. Vector Neutral Truck Cycle: 1.) Travel from the load station to the dump station. 2.) Stop and dump load. 3.) Travel from the dump station to the load station. 4.) Stop and load. The Advantage is in the Difference: 1.) Shorter distance traveled. 2.) Fewer brake and steering actuations. 3.) Easier to automate. 4.) Easier to adapt for remote control operation.

May 1, 2003

By Olman Hee

This study investigates the identity and relative importance of factors affecting the future demand for phosphate rock, potash, and nitrogen. The main objective is to analyze demand relationships for these chemical raw materials for some specified past period, and to utilize this information to make projections of consumption into some designated future period. The end-use approach is used, which divides total consumption of each chemical raw material into agricultural, industrial, and export use. Multiple regression analysis is employed to statistically measure the relative effects of the different factors on consumption in each end use. The general method centers on the construction of a consumer demand model, the fitting of the respective equations in the model, and the interpretation of the statistical results. Direct and cross price elasticities of demand are computed for each end use of the chemical raw materials. These give an insight into expected changes in consumption with respect to given changes in price. The results of this study indicate that price, consumer income, and level of technology are factors which measurably affect consumption of chemical raw materials. For phosphate rock and potash, the agricultural and industrial end uses showed an inelastic demand, whereas for nitrogen, all end uses (including export use) exhibited an elastic demand. Among the chemical raw materials, average annual growth of consumption of nitrogen for agricultural and export uses to 1980 is expected to be notably higher than that for phosphate rock and potash.

Jan 1, 1969

The green field site is one that has no history of mining and as such it presents the designer with a blank canvas, on which any number of drill and blasting options can be drafted. No matter which mining method is selected all technology and experience will need to be acquired from outside sources, applied quickly and produce the right results. North Limited, in joint venture with the Sumitomo Group (20 per cent), have developed AustraliaÆs first block cave mine at Northparkes in New South Wales, Australia. This innovative and large scale mining project was taken from a green field site in November 1993 to a fully commissioned block cave mine in December 1997. NorthparkesÆ Endeavour 26 mine is now producing at a rate of 3.9Mt per annum from a 27Mt ore block. Prior to 1993 no history of mining activity existed at Northparkes. The rock had never been blasted and many questions were raised about how it would behave. While it was clear that the Endeavour 26 (E26) orebody contained geotechnical properties appropriate to block caving, the blasting methods required to establish a block cave mine had never been used in Australia and no designs were available. The joint venture partners had no prior experience with block caving and it was immediately apparent that this blasting technology would have to be acquired from foreign sources and applied to the unique local conditions. Conceptual designs for the block cave drill and blast were first drafted in 1994, first issued for drilling in December 1995 and first blasted in January 1996. 470 km of drill metres and four million tonnes of rock were blasted to complete the undercutting project by September 1997. This paper will provide those developing new drill and blast projects with an inside view of how one small technical team solved many design challenges to successfully construct AustraliaÆs first block cave mine under strict quality controls and ambitious time constraints.

Jan 1, 1998