Search Documents

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929

By S F. Simmons

At Broadlands-Ohaaki geothermal system, TVZ, mineral distribution patterns in geothermal wells are analogous to those in epithermal veins. Fluid flow through geothermal wells is focused over vertical intervals >500 m with discharge at rates up to 90 l/s. Focused flow at similar rates also occurs in natural systems where hydrothermal eruption vents provide enhanced vertical permeability. These vents are commonly aligned with the tectonic fabric, indicating fault control at depth. We suggest that host rock strength and structural context exert significant control on the hydrological regime conducive to epithermal mineralisation.

Jan 1, 2005

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Mengxiong Guo, Xuxin Shao

The recent depressant research is summarized, and a new kind of depressant (SCO) has been put forward in this article. Using Na-oleate as a collector and SCO as a depressant, separation of dolomite and phosphate was studied. When SCO was added in the concentration range of 80 g/t to 2kg/t at pH 9.5 ± 0.2, dolomite was absolutely depressed, and apatite kept its floatability. Interestingly, in the mixture of phosphate and dolomite, the dolomite floated. The reasons for such a behavior are investigated through flotation and electrokinetic studies. It was found that the adsorption of dissolved species on dolomite and phosphate resulted in reverse flotation. A concentration of 31.59% P205 and 83.87% recovery of P205 was obtained from the mixture of phosphate and dolomite (2:1) with 26.6% P205 using 210 g/t SCO and Na-oleate 4.93*10-5 M at pH 9.

Jan 1, 1989

By Pharis E. Williams

The ability to predict the performance of an explosive relies upon having a Reaction Rate Law and knowing its functional dependence upon various parameters of the explosive. In particular, emulsion explosives have a matrix cell size and may be sensitized with glass or plastic microballoons. The cell size dependence should. be very nearly the spherical grain burning dependence upon web that appears in the reaction rate laws for ball gun powder. The dependence of the reaction rate law upon the parameters of the sensitizing microballoons has been explored using hydrocode analysis of the pressure field produced by the collapse of a microballoon. This pressure field provides an increase in pressure in the vicinity of the microballoon which, in turn, increases the rate of reaction within this field and provides the energy release that must be achieved in order to have a steady state detonation for use as a blasting agent. Hydrocode analysis allows the determination of an approximate functional form for the reaction rate law which shows the dependence upon the size, type, and quantity of microballoons. This presentation includes the theoretical background and the determined functional form of the reaction rate law.

Jan 1, 1995

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

Distribution of Settling Velocity of Irregular Particles and its Effect on Jig Separation Efficiency

Sep 13, 2010

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By Alberto Pacheco Pacheco

En el presente texto se analiza el fundamento de lógica fuzzy aplicada al control de molienda de minerales, la que nos permite simular el comportamiento humano en la operación molienda, con la que se plantea el algoritmo de control inteligente de molienda.

Sep 12, 2005

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By Malcolm Arnesen

Mineral Resource Management (MRM) is a business concept with the purpose of increasing throughput by management of key process variables to optimize ore utilization. To achieve a MRM process focus there are four principles that need to be applied to the business. In this sense, the paper define these principles and describe how they are applied to the mining business using Thabazimbi iron ore mine as an example. Also the article deals with the generic approach to Mineral Resource Management and the second part with the application and success of MRM at Thabazimbi Iron Ore Mine.

Jul 17, 2000

By Steve Lalancette

Centre Jardin Lac Pelletier (CJLP) has been a leading actor in the revitalisation of closed mining sites in northern Québec for over 20 years. Over that period, CJLP developed a cost-efficient technique that transforms sterile mining residue into a substrate able to support a resilient ecosystem. Using a unique mix of organic matter, fertilisers and selected plant species, this technique rapidly builds a microorganic fauna and a layer of humus that will sustain the creation of vegetation coverage. The coverage is composed of over 13 different plant species, each having a unique role in the development of a resilient ecosystem, from soil stabilisation to nitrogen fixing. Considerably less expensive than traditional methods using civil engineering techniques, it does not require the use of heavy machinery or the spread of topsoil. This technique has been successfully used to restore over 20 sites in Québec such as Joutel, Yvan Vézina and Louvicourt. It is a proven technique that has passed the test of actual implementation. The presentation will review the biological, production and economic aspects of the technique through the revitalisation of the Joutel site.

May 1, 2011

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Maurus Seet Hong Hua

Introduction Coal has always been China's predominant energy resource. The country ranks among the three richest countries in coal reserves in the world, next to the US and the Soviet Union. According to China's Ministry of Coal Industry (MCI), coal accounted for about 72% of the total national energy consumption. Despite efforts to increase the output of oil and hydropower, coal is predicted to remain dominant on the energy scene by increasing its share to 77% by the turn of the century. To match the rapid growth in the agricultural and industrial sectors, MCI has targeted the coal industry to double coal output from 600 Mt/a (660 million stpy) in 1981 to 1.2 Gt/a (1.3 billion stpy) by the year 2000. How is this goal to be achieved? According to MCI, it will be accomplished by: • building new underground and surface mines with a total output of 400 Mt/a (440 million stpy); • increasing the output of existing state-controlled mines from the present 344 Mt/a (368 million stpy) to 400 Mt/a (440 million stpy); and • developing and increasing the output of small, local mines run by province, county, and production brigade from the present 276 Mt/a (304 million stpy) to 400 Mt/a (440 million stpy). Building new underground and surface mines New underground coal mines will be developed in areas where the coal industry has already made headway and infrastructures currently exist. This is to optimize hardpressed capital spending on investment. Ten existing coal production bases were selected in nine different provinces that met these requirements. The underground mines scheduled to be constructed in stages at he existing coal production bases will have a total output of 200 Mt/a (220 million stpy) by the end of the century. Regarding surface mines, four mines in the Inner Mongolia Autonomous Region and one in Shanxi province have been earmarked for construction during the same period. By the year 2000, these surface mines are expected to produce 200 Mt/a (220 million stpy). Foreign equipment, machinery, and surface mine stripping technology were all involved in different degrees in the development of the five new surface mines. Some have signed joint venture agreements. Occidental Petroleum Corp. is in a joint venture with China in developing Ping-shou's 15 Mt/a (16.5 million stpy) Antaibao No. 1 open-pit. The Shentou power station, situated nearby, is anticipated to consume 3.2 Mt/a (3.5 million stpy) of the coal it produces. Some is designated for export. Increasing output There are 554 state-controlled mines that have been in operation since before 1980. They produce 344 Mt/a (379 million stpy). To increase capacity, MCI has laid out some guidelines. • Coal prospecting near existing mines must be given top priority and intensified so that workable reserves can be increased. This would lengthen the mines' useful life. • Many mines and slopes that were constructed during the 1950s are very small and densely populated. These small mines and slopes are generally very short along the strike. As a result, coal faces and levels require frequent

Jan 3, 1986

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009

Objective: To help prevent squeezes, collapses, and other pillar failures through better pillar design, thereby enhancing safety for underground mine workers.

Jul 1, 1997

What decision making tools and methods are available to a project owner when there is no clear differentiator between construction alternatives? A team led by a joint venture of Parsons Brinckerhoff and PGH Wong Engineering (PB/Wong) has been providing preliminary engineering services to the San Francisco Municipal Transportation Agency (SFMTA). The SFMTA and PB/Wong team developed several alternative construction methods for the tunnels and stations of the San Francisco Central Subway Project, none of which could be judged clearly better than another using traditional approaches and metrics. The team employed a risk assessment and analysis frame-works as a means of comparative analysis, drawing upon the knowledge of industry experts in the geotechnical, tunneling and construction fields to assist in the effort. This paper presents the approach and results of a cost and schedule risk analysis for two such analyses designed to answer two different questions regarding the advisability of different construction approaches. These assessments paved the way for key decision making in the preliminary engineering phase of the project and formed the foundation for continuing risk management efforts on the project. The focus of this paper is primarily the first two stages of risk management?identification and assessment?and some of the organizational dynamic issues that arise in such efforts.