Search Documents

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion' as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as 'worn out'. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By S. J. Dillingham

As we enter the new century and close out the old, it has become standard procedure for most blasters to complete a blasting log or shot report following a blast. However, how can you be sure these completed blasting logs are worth the paper or electronic space they occupy.3 Is the recorded data accurate and meaningful? Will the blasting logs stand up under investigation? This paper will attempt to define the purpose of a blasting log, illustrate common mistakes, discuss potential problems, and indicate steps that a company or individual blaster can take to improve and protect against costly errors. The end result will be a reminder of the importance of accurate documentation following a blast that must be given the same individual effort as went into the blasting itself. This paper will also attempt to achieve a proactive training resource to improve the use of blasting logs. A completed blasting log is, quite possibly, the only witness to the overall credibility of the work of the responsible blaster. The log may remain perpetually silent, only to end up in a file that is moved progressively with time to various levels of long-term storage. But, will this silent witness be ready to speak out should a concern arise from the blasting ? Will the blasting log communicate with authority and credibility, or will it be ridiculed by investigation and silenced in shame with costly adverse results for the blaster and company? It is not enough to simply complete a blasting log. The information it contains must be accurate enough to stand the test of time and arduous scrutiny. Unfortunately, most blasters and their associated blasting companies do not realize the status of the silent witness until it is too late.

Jan 1, 2000

By A. Ouchi

This paper presents ground control best practices in weak rock environments including the "Unsupported" Weak Rock Updated Span Design Curve and awareness pertaining to the potentially detrimental effects of using resin grouted rebar in weak rock masses and the false sense of security that the use of resin grouted rebar may instill. Ground support is almost always used in weak rock environments, though the type of support used can vary widely. The development of the Weak Rock Updated Span Design Curve by the addition of 463 case histories of RMR76 values ranging from 25 to 60, has also been calibrated to four different support categories; Category A: Pattern Friction Sets, Category B: Pattern Friction Sets with Spot Bolting of Rebar, Category C: Pattern Friction Sets with Pattern Rebar Bolts and Category D: Cablebolting, Shotcrete, Spiling, Timber Sets or Underhand Cut and Fill. Design of underground man-entry type excavations in North America relies heavily upon empirical analysis. This design requires a higher Factor of Safety than other non-man entry type excavations. A comparison of the calculated ½ span failure Factor of Safety between all the categories is also presented.

May 1, 2009

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

Enterprise Optimisation is a methodology for increasing the value of mining and mineral processing operations through better long-term planning decisions. It involves a combination of ten mechanisms which deal with decisions at different stages of the value chain. A decision made at any point in the chain potentially affects the decision for all other points in the chain. The key, therefore, is to optimise them simultaneously. The Enterprise Optimisation approach can be shown to produce increases of five per cent to 35 per cent or more in net present value (NPV), even when several optimisation methods have already been applied. This paper steps through an example case study, illustrating the effect of each mechanism and how they can work together to develop greatly improved results. This example results in a series of counter-intuitive outcomes, which challenges conventional management practices and typical organisational objectives based on organisational silos.

Dec 6, 2010

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

In its April 1991 issue, MINING ENGINEERING published a salary survey form asking for information relating to engineering and management jobs in the minerals industry. 1038 of these forms were filled out and returned, most of them being received in the magazine's offices at SME headquarters before the end of June 1991. An SME volunteer took on the task of tabulating and analyzing data from the forms, but the press of other business interfered with this work, and publication has been delayed until this issue of MINING ENGINEERING. Appreciation is extended to SME members who took the time to fill out and return the salary survey forms, and our apologies go to MINING ENGINEERING'S readers for the delay in publication. Of the total number of forms received, more than 97% were from SME members. The geographic distribution of the respondents closely mirrored that of SME membership as a whole, about 50% being from the Society's Western Region, 19% from the Central Region, and 23% from the Eastern Region. About 8% were from outside the US. Average salaries for each of the four geographic areas ranged between $55,000 and $60,000, with the highest average in Eastern Region (Fig. 1). Respondents were asked to answer a number of questions formulated to determine if there are significant differences in salaries based on the type of organization for which they work. As indicated by Table 1, salary averages at mining companies do not vary markedly with the size of the company: • Large companies, defined as those having more than $1 billion in annual sales, accounted for just over 16% of the returns. Their average salary was $61,840 per year.

Jan 1, 1992

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By C. E. Doran

Since the early 1990s the underground mining industry has embarked on a vigorous program of improving process and eliminating costs. A leading development in this program has been the implementation of leaky feeder radio systems as an enabling infrastructure for future automation. El-Equip Inc. has led this development with more than 175 mines implementing mine-wide radio infrastructures for voice and data. In this paper, we describe the implementation of a digital radio network which supports existing installations through to an automation infrastructure employing full digital cellular communications with mobile video roaming capabilities. We outline the evolutionary path from existing low speed data communications links through to 155 Mbps and beyond.

Sep 1, 2001

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

By Albert H. Fay

Through the hearty cooperation of the State coal-mine inspectors, the bureau is able to present in this paper a a complete statement of the coal-mine fatalities occurring throughout the United States during the calendar year 1919. The reports received from the inspectors for the year just closed show a reduction of 10.58 per cent in coal-mine fatalities as compared. with 1918, while in 1918 the reduction was 4.3 per cent from 1917 figures. The total number killed was 2,307 in 1919 and 2,580 in 1918, a reduction of 273. There was a decrease of 128, or 25 per cent, in fa tali ties resulting from mine cars and locomotives, and a decrease of 198, or 15 per cent, in the fa tali ties due to fall of coal or rock. Surface accidents show a decline of about 25 per cent as compared with the previous year. There were, however, increases in accidents due to gas and dust explosions and also explosives. There occurred during the year nine disasters in which five or more men were killed, representing a total of 201 fatalities. The worst disaster of the year was the one occurring at the Baltimore Tunnel No. 2, Wilkes-Barre, Pa., resulting from the explosion or burning of a number of kegs of powder, by which 92 lives were lost. This disaster emphasizes the need for stricter regulations relating to hauling men and explosives into the mine at the same time. The question of whether electricity was responsible or not does not affect the consideration of the various dangers which arise in underground transportation and handling of explosiveB. At best the handling and hauling of explo.sives is hazardous and such being the case, no one, other than the necessary attendants, should be permitted to ride in cars or cages transporting explosives. As a result of this disaster, the report b of the coroner's jury to the governor of Pennsylvania brings out some important dangers to be avoided in the use and transportation of explosives.

Jan 1, 1920