Search Documents

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

Recovery Process of Carbon Dioxide with Metal Oxides and Metal Hydroxides

Sep 13, 2010

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By P E. H Gregg, R B. Stewart

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed.   After seven years, the rate of increase of N, C, P and S, losses of Sand P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site. Further tailings trials have been initiated to investigate alternative land use options for the tailings dam. Growth increases of 73% occurred in native species growing directly in tailings, and growth increases of 78% occurred in tailings amended with compost over the first six months. Pasture trials on tailings with and without a compost amendment have also been initiated. Research has commenced to investigate the restoration options for acid producing pit slopes. The early field trials have been put into practice with the restoration of oxidised waste on the tailings embankment. This is progressive with approximately 16 ha restored to productive pasture at present. Yields compare well with those of the most versatile and productive soils types investigated in baseline studies of the area before the tailings dam was constructed.

Jan 1, 1995

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By K. G. Kebkal, R. Bannasch

"Because the operation of tethered underwater vehicles in the deep ocean or under drifting ice areas is very complicated or impossible, the application of autonomous underwater vehicles (AUV) is preferred or even the only possible solution. However, this implies the possibility of a direct and real-time control over all AUV functions, which is only achievable with the availability of accurate positioning/navigation and a high-speed communication link. This paper presents a flexible bottom- or surface-based solution enabling high positioning accuracy of underwater objects (harvester, AUVs, bottom nodes); specifically, a multifunctional system that combines Ultra Short Baseline (USBL) transceivers and Long BaseLine (LBL) stations deployed at a large depth. Moreover, each baseline transponder is equipped with a high-speed communication device to provide the means for real-time AUV control based on the information about its current position, e.g. navigate it with direct commands and operating its actuators and other mechanisms. Moreover a communication link with a high data rate can provide valuable visual information from the operation area.Depending on how many nodes the LBL grid comprise has, target transponder positions can be estimated with an accuracy of several to tens of centimetres. The purpose of the paper is to present the experiments with all key elements of the multifunctional Hydro-Acoustic USBL-aided LBL Positioning and Communication System."

Sep 1, 2014

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By William W. Odell

Certain gas-making processes are in use in Europe, particularly in Germany, which differ radically from those in common use in America. A number of them are of particular interest because they are different. The questions naturally arise: Are any of them applicable to the making of gas in this country and, if so, with what particular type of solid fuel? It is a fact that some of them were developed with consideration of a particular set of conditions and for the utilization of solid fuels available in Germany. The latter fuels, in certain characteristics, are unlike the high-rank fuels commonly used for making gas in the United States; therefore, in attempting to evaluate the various foreign- developed processes with regard to usefulness here, one must give attention to the particular conditions that will prevail in any specified case and also the characteristics and requirements of the process and generator under considera- tion. Three of the processes that were developed and put into commercial operation in Germany, and which have some characteristics in common, are con- sidered in particular in this publication; they are: 1. Lurgi pressure gasification process. 2. Winkler process. 3. The Leuna slagging-type producer-gas process. Each of these processes requires steam and oxygen as gas-maiding fluids. For a number of years, oxygen, has been used in a relatively pure state,. along with steam, in making gas in Germany, and many of the difficulties initi-. ally encountered have been overcome. Although it appears that oxygen recovered from air was first used in this manner as a method of utilizing a byproduct in a plant that used the nitrogen complement in the manufacture of ammonia; more recently, the oxygen was made particularly for the purpose. The fuels - brown coal or lignite used in processes 1 and 2 were not suitable for use in the older and commonly used intermittent-type water-gas generators, and it was necessary, therefore, to devise a different process for gasifying them. A gas of higher heating value than producer gas, was desired, and the use of oxygen (not air) along with steam made possible the production of the desired gas without nitrogen dilution, which characterizes producer gas. Operating data presented herein are based upon observations by, members of the Technical Oil Mission at plants in Germany, on records, and on information vocally given to members of the lässion, including the author, while visiting those plants, and they are believed to be reasonably correct; however, certain hasic observations, comparisons, and conclusions are. made by the author.

Nov 1, 1947

By David Ziegler

Rough sketches, field notes, an on-site conference or a phone call may no longer suffice to establish your blast plan at a job site. More and more, general contractors, site supervisors, owner re p resentatives, or the owners themselves want to know details about proposed drill and blast operations at their site, in advance. We are seeing more contracts that re q u i re a blasting plan to be submitted in writing. The purpose of this session is to discuss items that you might want to include and address in a written blast plan, and some ideas about how to present them. This is not intended to be a complete list of items that could be included in a blast plan. Contracts may list specific items that need to be addressed. Only a few of the more common elements will be covered here. The bro a der purpose of this discussion is to get you thinking, about what you might want to include in your own “standard ” blast plan.

Jan 1, 2004

By G. R. Brough

"Today it is more important than ever to get the maximum possible return on capital invested in the processing industry. To this end the plant is often operated continuously and the choice of equipment is, consequently, extremely important.Screening spans a wide range of particle sizes and there are many different types of screening elements. The following types are common:1. Cloths and elements of rubber.2. Wire mesh screens with round wires.3. Wire mesh screens with profiled wires.4. Perforated steel plates.5. Elements of plastic.6. Gratings of steel beams.7. Gratings of iron rods.We would like to deal with two of these types namely rubber and briefly on plastics.We first introduced rubber screens to the Canadian Mining Industry in November, 1963. This stemmed from a conversation with the superintendant of one of Canada's largest screening plants containing 48 vibrating screens, with an average wire cloth life of 10 to 12 days. We contacted the manufacturer of rubber screen cloths who had supplied rubber screens to a mine in Northern Sweden for a 50,000 ton per day plant in 1951."

Jan 1, 1983

By Roberto Chambi

"El presente trabajo señala la expansión de la producción de la mina Condestable a través de las innovaciones tecnológicas en clasificación de molienda como: la utilización de estas zarandas derrick de cinco pisos cada uno, donde se aumenta la capacidad de cada molino instalado en planta en un 17% en promedio, así como el grado concentrado supera el promedio de 26.35%."

Sep 9, 2007

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By Raymundo Del Carpio

El presente trabajo señala las bases que fundamentan la aplicabilidad del extracto de quebracho como depresor en el proceso de flotación, donde se realiza una combinación de un dispersante (producto obtenido a partir de extractos vegetales). También se muestra los avances sobre procesamiento de minerales con alto contenido de pirrotita. En ese sentido, se busca desarrollar una tecnología eficiente y ambientalmente limpia, considerada como una herramienta para la mejora de la competitividad de la empresa, a partir de una visión de desarrollo sostenible.

Sep 9, 2007