Search Documents

By D. S. Burgess

About 100 tests of flammability were carried out with H2, CH4, and CO in mixtures with air using the Federal Bureau of Mines 12-ft-diameter spherical pressure vessel as an explosion test chamber. The LeChatelier approximation gave slightly conservative estimates of the limits of downward flame propagation (onset of significant pressure rise) using the following measured values for the individual gases, in percent: H2, 8.5; CH4, 5.25; CO, 13.0. No justification could be offered for using the LeChatelier law for upward flame propagation limits and indeed reported data suggest that calculated values would not be conservative. The observed upward limit for methane-air mixtures (4.85 pct) was less than the widely accepted lean limit for this fuel; those for lean hydrogen-air mixtures and carbon monoxide-air mixtures did not differ from the lowest accepted values. Diffusional effects on the propagation of single, binary, and ternary fuel mixtures are discussed.

Jan 1, 1982

By H. E. Thomas

[The Bureau of Mines has conducted a field hydraulic fracturing experiment to determine the preferential orientation of induced fractures in oil shale at a depth of about 400 feet in the Green River Basin of Wyoming. The hydraulic fracturing treatment was performed by injecting extremely viscous water-base gel and 8- to 12-mesh sand into the oil shale through straddle packers set in an impermeable section of smooth-walled, 6-1/4-inch-diameter open hole. An impression packer proved that a horizontal fracture, which has an average width of about 1/2 inch at the borehole, was induced. A corehole drilled 100 feet from the fractured well intersected the fracture and confirmed its horizontal orientation. Because a horizontal fracture was successfully initi¬ated, it is inferred that the creation of multiple, closely spaced horizontal fractures may be feasible in Green River Basin oil shale.]

Jan 1, 1972

By Wijnand Dalmijn, Hans de Ruiter

Experience over the past eight years has proven that partnership and cooperation in mineral engineering education is essential to maintain programs in this field. At this moment the joint European Mineral Masters Engineering Course (EMMEC) has three programs in the areas of mining, minerals engineering and geotechnical/environmental engineering, offered by combinations of nine universities in seven European countries. About 25 companies are associated with the universities in the Federation of European Mineral Programs (FEMP) which coordinates these activities. The EMMEC has applied for recognition under the newly launched EU “Erasmus Mundus” program in which the EU makes 280 million Euro available for bursaries for non-European students and scholars.

Jan 1, 2005

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800's. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Ed Billington, Mike Shields

The trail blaster is faced with a wide range of workrelated challenges, not the least being the work setting itself. It is usually remote, being anywhere from 5 to 30 or more miles (8 to 50 km) from any road. It may be in mountains, high rock desert, or coastal rain forest, and can range from sea level to over 12,000 feet (3700 m) in elevation. The blaster may be part of a 2-person clearing crew, a 4-person maintenance crew, or a 10-person construction crew. The crew will usually be mobile, moving and working up to 10 miles (16 km) or more per day, relying mostly on their own backpacks to move camp, tools and supplies from site to site. Periodic resupply may be by helicopter, aird rop, or even “sherpa” groups, but most often will be by packstrings of horses and mules. The crew goes into the backcountry a n y w h e re from two weeks to three months at a time, and while there, its members “live the job” 24 hours a day, enjoying baking heat, torrential rain or mid-July s n o w s t o rms along with the truly glorious weather that c o m p e n s a t e s . So who is this blaster? Well, “he” may be she, since some of the top trail blasters are women. He/she will also be more than a blaster: Crews are small, so experienced members must be capable of handling the full range of trail work. Thus this blaster is also a driller, and usually also a bucker, snag faller, rigger, dry-stone mason, log and timber carpenter, bridge builder, mule p a c k e r, small-engine mechanic and, not least, camp cook capable of putting out a hot meal from a campfire , in a downpour, in the dark. Being in remote locations, often without reliable communication to the outside world, trail crews enjoy a remarkable degree of independence from “supervision.” With that comes the responsibility to make sound decisions which expedite the work, while promoting crew safety and welfare .

Jan 1, 2004

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

The purpose of this paper is to outline current research on the Paparoa and, at the request of conference organisers, to present a general introduction to the geology of the Greymouth Coalfield as background to more specialised papers. Few results of my present work will be given; these can be presented at the next conference. Briefly, the research aims for an understanding of the controls which depositional environment has exerted on coal character, to be reached by a study of coal type and thickness, shape and extent of seams, integrated with a basinal analysis of the coal measures. An accurate description of the coalfield in these terms should facilitate prediction of subsurface trends, with possible application to the planning of drilling programs, and to mine development. Although study of Paparoa coal types is included here as only part of the research, coal type should be recognised as an important concept which has until revently been almost entirely neglected in New Zealand.

Jan 1, 1979

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968