Search Documents

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By D. J. Thorkelson

New data indicate Wernecke Breccia-associated iron oxide copper-gold (IOCG) deposits likely formed from moderate-temperature, high-salinity, non-magmatic brines. The breccias formed in an area underlain by a sedimentary sequence that locally contained evaporites (potential source of chloride and possibly sulfur) and was thick enough to produce elevated fluid temperatures. Metals (Fe, Cu, Co, U) were probably derived from host strata, transported as chloride complexes, and precipitated due to changes in fluid temperature and pressure during brecciation. These new data suggest that the spectrum of genetic models for IOCG deposits that typically invoke formation from magmatic or hybrid magmatic-non-magmatic fluids should be expanded to include those systems that formed in a non-magmatic environment. Modifications to the definition of IOCG systems are proposed that reflect the degree of involvement of magmatic and/or non-magmatic fluids and the nature of the mineralizing environment. A division into magmatic, non-magmatic, and hybrid magmatic-non-magmatic IOCG types is suggested. Typical magmatic end-member IOCG deposits include Lightning Creek and Eloise, Australia. Hybrid magmatic-nonmagmatic IOCG examples include Ernest Henry and Olympic Dam, Australia. The Wernecke Breccia and Redbank deposits are suggested as possible representatives of non-magmatic IOCG end members. Endmember magmatic IOCG deposits have similarities to some porphyry deposits, whereas non-magmatic IOCG end members share characteristic with some sediment-hosted Cu deposits, suggesting that the range of IOCG deposits may form a link between intrusive- and sediment-related deposits

Jan 1, 2007

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By Steven R. Munts

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the South Providence Wilderness Study Area (WSA) in 1982. No mines are currently operating in the WSA, however, the Golden Gift Mine in the southeastern part of the WSA produced $6,800 1/ worth of gold and silver and five mines adjacent to the east boundary of the WSA had a total production of about $3,500,000 1/ in gold, silver, lead, and copper. There is no recorded placer gold production. Over 350 lode and placer mining claims are in and immediately adjacent to the WSA. Of these, 74 were actively held (1982) and at least one area, which is partly within the northeast portion of the WSA, was being actively explored by private industry in 1982. Adjacent to the southeastern border of the WSA the Big Horn Mine contains an estimated 200,000 tons of indicated and inferred marginal reserves averaging 0.25 oz/ton gold; and the Hidden Hill Mine has 550 tons of subeconomic resources averaging 0.60 oz/ton gold. An additional 11,000 tons of marginally economic gold-bearing dump reserves average 0.17 oz/ton gold at the Bighorn, Hidden Hill, and the Buena Vista Mines and the Midas Touch Prospect. Sample analyses indicate eight mines and prospects in, and five adjacent to the WSA may have additional gold-silver-lead-copper vein-type resources. Five of these prospect areas may have a disseminated gold resource and one may have gold resources in a skarn. One prospect may have a porphyry-type copper-molybdenum resource. Although gold placer claims were filed sporadically throughout the WSA, none appears to have placer gold resources. Likelihood for mining is greatest at the Big Horn Mine; if a mill is built there, it could process Big Horn Mine ore, ore from the Hidden Hill Mine, and gold-bearing dumps at the Big Horn, Hidden Hill, and Buena Vista Mines and the Midas Touch Prospect. All of these resources are adjacent to the WSA; however, their development would increase likelihood for development of resources in the WSA. Two major fault zones (the Hidden Hill, and the Big Horn) appear to have controlled the mineralization at many of the prospects and mines. All of the prospects or mines with vein-type occurrences and resources are on or adjacent to one of these fault zones. Veins throughout the eastern half of the WSA contain various amounts of gold, silver, and copper; only veins near the Big Horn Mine and in the northeastern corner of the WSA contain lead. Some veins are as thick as 6 ft, are traceable intermittently for over 2 mi along strike, are sporadically mineralized, are encased in prophylitic, argillic, and phyllic altered host rock, contain pyrite, chalcopyrite, galena, specularite, barite, or fluorite, and display multiple stages of quartz veining and (or) brecciation. Sample analyses at five prospects (map nos. 3, 18, 23, 24, and 31) indicate they may have disseminated gold resources. To date no oil or gas has been discovered within the WSA. However, some oil and gas leases are currently (August 1982) held within this study area.

Jan 1, 1984

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By C. D. Hebert, M. R. King

The 56,000' (17 km) long San Vicente Aqueduct Pipeline tunnel is being constructed using precast concrete rings to act as preliminary ground support through two sections of the bored tunnel with lengths of 9,450' (2.9 km) and 33,700' (10.27 km).The six segment bolted trapezoidal ring was manufactured using a combination of steel fiber reinforced concrete and self compacting concrete in vertical moulds. This paper briefly describes the design and function of the segments, and reviews the development stages of the concrete mix, and the advantages and disadvantages of the adopted manufacturing method.

Jan 1, 2007

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By I. Bhattacherya

Over the last three decades, the mining industry has been moving towards underground mechanized mining methods and the number of load haul dump (LHD) vehicles utilized has increased. The growth of mechanization and automation has benefited both workers and mining companies. However, due to the design constraints with LHD vehicles and the limitations of the operating environment, restrictions to operator visibility has contributed to a number of accidents, including fatal injuries. Past researchers have used the light filament technique to collect obscuration zones around mobile equipment and have produced 2D visibility charts (shadow diagrams) of this information. The light filament method involves manually collecting visibility data, which results in errors and is time consuming, requiring around three hours to complete. This research utilizes a MENSI GS100 laser scanner along with 3D modelling software (3Dipsos) to collect and process operator visibility profiles for underground mobile equipment. Results from this test work indicate that a laser scanner can be successfully used to rapidly collect this data and utilize this information for improved mobile equipment design from a visibility perspective. Nomenclature FERIC Forest Engineering Research Institute of Canada ISO International Organization for Standardization JACK Software for digital human modelling and ergonomics LHD Load haul dump vehicle LOS Line of sight MASHA Mines and Aggregates Safety and Health Association (based in Ontario, Canada) PVD Polar visibility diagram SAMMIE3D human modelling computer aided ergonomics design system WSIB Workplace Safety and Insurance Board

Jan 1, 2006

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By C. B. Manula

Bituminous coal mining in the United States is currently experiencing a period of rapid growth which began in the early 1960's. Future demands are conservatively predicted to rise to 700 million tons by 1980 and to anywhere between 1 to 3 billion tons by the turn of the century. This means a continuous expansion of coal production by a factor of at least two can be expected before the end of the century. Over the last few years, production from underground mining has decreased; yet it is about 50% of the total coal output. In the absence of any discovery of near surface coal deposits, and even after conceding that some deeper deposits can be surface mined with changes in technology it can be reasonably assumed that coal production from underground will continue to play an important part in solving the energy crisis.

Jan 1, 1975

By Don W. Lake

Of all the blast monitor& instrumentation systems and techniques av&able today, highspeed photography and videography remain as the most valuable, stand alone, diagnostic techniques to evaluate full scale blasts in the mining and explosives industries. Highspeed image data, coupled with information from other instrumentation systems, such as continuous VOD records, seismographs, laser surveying systems, refraction seismographs, etc. can eIiminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both good and bad blasts is increased, and optimum blast designs are achieved considerably faster when compared to the trial and error approach or relying on just the experience factor.

Jan 1, 1992

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

WITH the exception of the deposits of the Milburn Cement Co near Dunedin, Wilson's Portland Cement Co., on the Mahurangi River (a short distance north of Auckland), and those of the New Zealand Portland Cement Co., at Limestone Island, the cement. Tesources of New Zealand remain practically undeveloped. The Milburn Company utilizes a mixture of limestone and mud for the manufacture of cement, while Wilson's and the New Zealand Portland Cement companies both have the advantage of a natural cement stock which requires but small additions of highgrade limestone to give the mixture required. The plant and deposits of the New Zealand Portland Cement Co are located in Whangarei Harbour, some six miles from thetownship of Whangarei. The works and dwelling-houses are situated on Limestone Island, which, with an area of 92 acres, and rising to a height of 212 ft., supplies the bulk of the raw material required. In addition to the island, the company possesses a high-grade limestone area of, roughly, four acres, situated on the mainland, 11 miles to the south. A better location for a cement works could not well have been chosen. On the east side of the island there is a deep channel, which never shows less than 18 ft. of water alongside the company's...

Jan 1, 1912

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By T Nassis, H M. Nel, T du Toit

Assmang Khumani Iron Ore Mine is exploiting the iron ore deposits that can be found in the Bruce-King-Mokaning farm areas in the Northern Cape, South Africa. The Bruce, King and Mokaning (Khumani) deposits are approximately 10 km south of the town Kathu, adjacent to the Sishen Mine. Assmang Limited is jointly owned and controlled by African Rainbow Minerals Limited and Assore Limited.Measurement, calculation and trending of plant throughput and chemical ore properties are critical in maintaining a successful beneficiation operation due to these values forming the basis of decision-making and thus promotion of efficient ore extraction. The Khumani management and engineering information system (MEIS) supplies information on key process parameters to an operational team and is required to do so within an optimal time frame, for maximum impact.Diverse data is put into the MEIS from multiple specialist systems, with interfaces that require manual intervention. Manual intervention is resource and time intensive to the point which limits the effect on the process and decreases the potential for value addition.Automation of interfaces decreases resource and time requirements, standardising plant wide data sources and providing the opportunity to provide specialist system data to decision-makers in a timely fashion, resulting in maximum impact on the process output.Engineering and metallurgical management systems were interfaced at Khumani Iron Mine by means of an automated table which facilitates the transfer of production data validated within the engineering system as input to the metal accounting system. This interface effectively assigns a master to each specialist data set employed for decision-making and delivers accurate process parameters to the production team within an optimal time frame, resulting in increased potential to improve beneficiation efficiency.CITATION:Nel, H M, Nassis, T and du Toit, T, 2013. The role of metallurgical and engineering information systems in the optimisation of iron ore beneficiation processes, in Proceedings Iron Ore 2013 , pp 453-458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Andrew M. Leszcykowski

In 1985, at the request of the Bureau of Land Management, personnel from the U.S. Bureau of Mines examined 18,700 acres of the 24,922-acre Eighteen Mile Wilderness Study Area to evaluate mineral resources. This study area is in east-central Idaho in Lemhi County, approximately 20 miles southeast of Leadore. The study area is underlain by Paleozoic marine sedimentary rock and Ordovician granitic rock. The sedimentary rock is primarily limestone and dolomite with a minor amount of siltstone. The Nicholia mining district borders the southern boundary of the study area. However, none of the district's mineral-bearing structures appear to trend into the study area. Just outside the northwestern part of the study area, on Clear Creek, is the E. J. Wilson and Sons? open-pit gypsum mine that operated until about 1977. About 120,000 tons of gypsum were produced from the mine for the cement plant at Inkom, ID, and for use as soil conditioner. Two theories for the origin of gypsum deposits are a hydrothermal source and a stratabound occurrence. Hydrothermal deposition is favored for this deposit. Occurrences of gypsum may exist in the study area. However, known reserves are adequate to meet needs for at least 800 years. There are no known mines, claims, or leases in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of part of the Eighteen Mile WSA (Wilderness Study Area) 1/ at the request of the Bureau of Land Management (BLM). The USBM examines and evaluates individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986