Search Documents

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By Aleksandar D. Bugarski

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

May 1, 2007

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982

By Fredrick M. Ryan

Present indications are that in about 2-3 years phosphor tags will be required in commercial explosives. A permissible 254 run ultraviolet lamp assembly has been developed to permit mine inspectors to detect such phosphor tags and therefore to establish if non-permissible explosives were used. This new lamp is powered by a Miner&apos;s cap battery without interference with the normal lighting requirements of the cap lamp battery. It is compact, light, and rugged with very high ultraviolet output.

Jan 1, 1977

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By E. Milke, A. Arnold, B. Friedrich, A. Sydykov

CaF2is often used as a fluoride addition to the chloride salt flux in the melting of aluminium scrap. The solubility of CaF2in the chloride salt system is limited. Dissolved CaF2is considered to improve the properties of salt fluxes. Experimental investigations indicated that the solubility ofCaF2in 70 wt % NaCl/30 wt % KCl, German salt flux used in aluminium scrap melting, might be lower than expected according to literature data. The pseudo binary section CaF2-(70 wt % NaCl-30 wt % KCl) was investigated by differential thermal analysis (DTA). The determined solubility of CaF2appeared to be considerably lower than presented in the literature. The pseudo binary section calculated using thermodynamic data partially confirmed the results. DTA allowed us alsoto determine the crystallization temperature interval of the two phase eutectic consisting of the solid solution NaCl-KCl and CaF2. Keywords: aluminium recycling, phase system, salt flux, CaF2, NaCl, KCl, solubility

Jan 1, 2004

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By Jim Gunderson

Jan 1, 2004

By S M. C Verryn, K Deysel

In heavy mineral sands ilmenite, rutile and zircon are present in economic concentrations. These minerals are important sources of Fe, Ti and Zr for various industrial uses. The beach sands of northern KwaZulu-Natal, along the Zululand Indian Ocean coastline in South Africa, have been mined for 30 years. The various processes involved in mining and processing these minerals have been controlled by time-consuming and labour-intensive analysis methods which, in some cases, can be replaced by X-ray powder diffraction (XRD)-Rietveld analysis. Heavy minerals are concentrated in the plant to produce a heavy mineral concentrate (HMC). The heavy mineral extraction plant is controlled and informed of the proportions of minerals in the HMC according to their magnetic susceptibility. The different fractions are called magnetic, paramagnetic and non-magnetic fractions and quality control is based on their magnetic fraction weights combined with X-ray fluorescence (XRF) elemental analysis. This current quality control process is very time consuming and labour intensive. We have aimed to show that we can, by XRD, identify and quantify all the minerals in the HMC and also in the magnetic separations. These results are then compared with results obtained by Mineral Liberation Analyser (MLA) as well as with the results from the physical separation. It was possible to detect all minerals present in the material by XRD and use the Rietveld method for a full bulk mineral quantification. A maximum of 15 minerals can be included in the Rietveld refinement due to computational restraints. Major minerals detected are rutile, ilmenite and zircon and minor minerals are quartz, epidote, anatase, amphibole, monazite, magnetite, titanite and augite. The XRD and MLA results correlate relatively well and detailed results will be presented for HMC and magnetic fraction samples. Small differences were observed for some minerals due to the different ways in which minerals are detected or due to preparation methods within each method. Rutile seems to be more abundant in the XRD analysis and the detection of Anatase is possible by XRD, but not MLA. Leucoxene (consisting of mainly microcrystalline anatase, rutile and titanite is not detectable by XRD since it is not a mineral, but ilmenite alteration phases are observed instead. There is, however, a correlation between anatase, titanite and rutile detected by XRD and leucoxene analysed by MLA.

Jan 1, 2008

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief&apos;s home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800&apos;s and give effective protection.

Jan 1, 1984

By Julie N. Walker

This U.S. Bureau of Mines report reviews the first 2 years of the agency&apos;s progress in implementing total quality management (TQM), which the agency refers to as Quality Improvement (QI). All employees have been trained in basic TQM concepts, a cadre of facilitators has been selected and trained, and 13 Bureauwide teams are addressing specific issues that were identified by Bureau employees nationwide as problem areas. Also in place are a Quality Council composed of the Bureau&apos;s top executives, a Quality Management Board, and eight QI Working Groups to provide a national 01 infrastructure. There are also Quality Steering Groups at each Bureau location nationwide to address local concerns. In addition to the narrative text, the texts of salient memoranda and other documents are included as appendixes.

Jan 1, 1992

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934