Search Documents

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By S L. Garwin

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Since the Eocene, New Guinea tectonics have been driven largely by the south-westerly-directed collision of accreted arc terranes with the northern margin of the Australian Craton, and subsequent westerly-directed transport of these exotic terranes by left-lateral strike-slip fault systems. The subduction of the Solomon Sea plate beneath north-eastern New Guinea in the mid- to late-Miocene led to magmatism and related gold-copper porphyry and epithermal mineralisation in the Maramuni arc and the formation of the Frieda River, Nena, Wafi-Golpu and other deposits.The development of the world-class porphyry and epithermal deposits in the Medial New Guinea magmatic belt, including Grasberg, Ok Tedi and Porgera, is localised by dilational zones formed about the intersections of north-easterly-trending, reactivated basement faults and north-dipping reverse faults related to the southward progression of the Papuan fold belt during the Late Miocene to Pleistocene. These deposits probably formed during short mantle-derived magmatic episodes in zones of regional isostatic uplift, which are attributed to the delamination of the lithospheric mantle beneath New Guinea.CITATION:Garwin, S L, 2015. The tectonics, geology and gold-copper metallogeny of New Guinea, in Proceedings PACRIM 2015 Congress, pp 151–164 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By Alex Olivas

El presente trabajo señala la tecnología de control e información aplicada a las zonas donde se han instalado diversos equipos de medición y control de una planta de almacenamiento, los cuales están interconectados con un PLC central mediante una red LAN y de bus de campo. Asímismo, se definen dichas zonas y se detalla donde sea pertinente las soluciones en las que se empleó la tecnología de control e información.

Aug 25, 2002

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the utilization of municipal solid waste. One of the primary objectives is the recycling of the magnetic fraction of municipal solid waste (raw refuse). This is consistent with one of the Bureau's goals, which is to minimize the requirements for mineral commodities by maximizing metals recovery from secondary domestic resources, In this investigation, cupola trials were made using combinations of refuse scrap with shredded automobile scrap under basic and acid slag practices. Furnace operating information and the behavior of alloying and tramp elements was obtained. The research showed that it is possible to utilize up to 60 percent refuse scrap in the cupola under basic practice and 30 percent under acid practice, Aluminum in refuse scrap, present in bimetallic cans, increased the recoveries of silicon and manganese charged to the cupola. Increased use of refuse scrap provided iron of lower sulfur. The alumina resulting from oxidation increased the slag volume. The aluminum and tin contents of the iron increased with increasing levels of refuse scrap in the charge. Lead was not a problem with respect to contamination of the iron. In basic practice, operation of the cupola was satisfactory since all slags were adequately fluid. In acid practice, operation became troublesome above the 45-percent level. Under both practices, the cupola iron melting rate decreased. Particulates in scrubber water and stack condensate samples contained lead, zinc, and tin, and the dust load increased. The tensile and transverse strengths of the iron produced under both practices are reported.

Jan 1, 1980

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995