Search Documents

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

The Development of a Non-Roasting Technology for Polymetallic Gold and Silver-Bearing Sulfide Concentrates Treatment

Sep 13, 2010

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By William C. B. Gates

Demolition blasting next to an active railroad can be very challenging because of track safety, blasting vibrations, potential track fouling by blast debris, and short work windows on a live track. Recently, in eastern Washington, one of the major railroad companies has been aggressively constructing a second main track to accommodate the expected increase in rail traffic of natural resource products. To accommodate construction of the second line, the railroad company used blasting demolition techniques to remove an old railroad trestle pier on the Milwaukee Road that was in the footprint of the new track bed. The trestle bridged the present rail line and flanked the track with two massive 550-ton (499 tonne) twin-columned steel reinforced concrete piers. The railroad contracted with a specialized contractor to remove the south pier using blasting demolition techniques. The blasting design presented the following challenges: blasting during live track conditions and short work windows; designing a V-notch blast pattern to ensure the pier fell away from the live track; drilling, loading, and timing of the shot; maintaining blasting vibrations at the track below 4 in./sec (102 mm/sec); maintaining ambient overpressure noise below 133 dB; control of fly rock and debris; and track protection and emergency debris removal plan.

Jan 1, 2016

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By Miguel Rutti

El presente trabajo señala la geología, litología y mineralización del yacimiento minero El Tapado del distrito Yanacocha, situado al norte de Cajamarca. Este se encuentra conformado por diferentes depósitos auríferos epitermales de alta sulfuración, los cuales se desarrollan dentro de un vulcanismo calco-alcalino de composición andesítica a dacítica de edad Mioceno y son correlacionables con la Formación Porculla del Grupo Calipuy. La geología del depósito está conformada por rocas porfiríticas (intrusiones) y flujos piroclásticos tales como tufos de cristales, tufos líticos y brechas piroclásticas afectados por eventos eruptivos de brechas freáticas - freatomagmáticas. Todas estas rocas han sufrido posterior alteración hidrotermal con ensambles típicos de sistemas tipo ácido-sulfato. La mineralización económica está controlada por procesos hidrotermales y se encuentra asociada a sílice masiva y sílice vuggy ( 1-10 g/t Au y estructuras de hasta 136 g/t Au ) y en menor grado sílice alunita y sílice granular (moderada a baja ley).

Apr 22, 2003

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By B. C. Lewis

Have technological advancements in underground coal mining driven people's skills to new highs or have the expanded skills of mining people driven the industry's technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer's (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

The Tennant Creek goldfield is situated in the Northern Territory, 360 miles north of Alice Springs, or a tot~l distance of 1,300 miles north of Adelaide, and 600 miles south of Darwin. The auriferous area extends 20 miles north and south by 50 miles east and west. The overland telegraph line and the AIice Springs-Darwin road pass through the centre of the field.HISTORY, PRODUCTIONThe country comprising the goldfield was traversed by J. MacDouall Stuart between 1859 and 1861 in the course of his last three exploring expeditions, which terminated respectively at Attack Creek, Newcastle Waters and at the mouth of the Adelaide River. The explorer named Tennant Creek and also Mount Samuel, on which mining operations are now in progress. The overland telegraph line was completed in 1872 and a relaying station established eight miles north of the site of the present township. There was no other settlement in the adjacent country prior to the opening up of the goldfield.Gold was discovered in 1926 on what is known as the Great Northern lease, three miles north of the township. The field was remote; the nearest plant at which gold ore could be treated was at Peterborough, in South Australia, 1,186 miles distant, and it was not until 1932 that the development of the field actively commenced.The production of the field from its inception to December 31, 1939, was 57,895 QZ. of gold, valued at £522,000, recovered from 61,793 long tons of ore, won from 98 mines. In 1940 seven of these mines had reached depths between 100 ft. and 230 ft., the workings of the majority being less than 60 ft. below surface.TOPOGRAPHY, WATERThe country is traversed by parallel and sub-parallel lines of hills trending east and west and rising to altitudes varying from 50 ft. to 100 ft. above the intervening valleys. The low ranges and isolated hills owe their survival to the resistance offered by their indurated, harder rocks to erosion which has removed the softer intervening formations. Their elevation and area depend to a considerable extent upon the presence of; and, the size of, the more or less exposed haematite formations, or are due to the influence of extensive siliceous dykes which traverse the locality.Watercourses head from the hills and either flood out on the flats within a short distance, or in a few cases follow longer courses to the northward. In the channels of the larger creeks billaoongs, which form important water storages for a considerable part of the year, -are to be found. Tennant...

Jan 1, 1942

By Tracy Brettmann

Equipment ? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2004

Australia is not capitalizing on the raw gems and precious minerals that it produces in abundance. In particular, there is an unrealised value for diamonds due to lack of processing after mining. Australia could enhance the value of its raw jewellery products by developing and integrated jewellery industry. For instance, initiation of a diamond industry would require training programmes to educate people in the requisite skills, such as diamond sorting, cleaving, sawing, bruting and polishing. Equally important would be the training of people in design jewellery, manufacturing, and appropriate diamond grading and sales techniques. Future technological advances in diamond processing will decide where the major diamond processing centres of the world will be. Australia, for a relatively small investment, could develop a highly productive diamond processing capacity using the new technology available. Australia's geographical position, and advanced banking and communication facilities provide the potential for this country to become a major trading centre for diamonds. KEYWORDS: Argyle Diamond Mine, Diamonds, Diamond Production, Diamond Sorting, Jewellery Industry

Jan 1, 1989

By D. J. Kunz

Myanmar Ivanhoe Copper Company Ltd. (MICCL) has been operating the Sabetaung- Kyisintaung (S&K) Project producing LME Grade A Copper Cathode using the Heap Leach-SX-EW Process since 1998. The mineralization is mainly Chalcocite and the mine has a life of 20 years at the designed annual production of 25,000 tonnes of cathode copper. Design capacity was achieved within two of months of start-up. The mine is among the world’s lowest cost, Heap Leach-SX-EW operations. Information regarding plant design and operation are presented along with the challenges lying ahead and the latest developments. Daniel Kunz is President and Chief Operating Officer of Ivanhoe Mines, and a director of MICCL. He has more than 20 years’ experience in mining, construction and engineering. Prior to joining Ivanhoe Mines in 1996, Mr. Kunz was Vice President and Controller of Morrison Knudsen Corporation, a major international mining and construction company. He was also President and Chief Executive Officer of MK Gold Company, a public mining company listed on NASDAQ.

Jan 1, 2001

By Abouzar Vakili

Longwall Top Coal Caving (LTCC), as the most attractive method for thick coal seams, has been suffering from insufficient geomechanical understanding for the past few years. Cavability without doubt is the most critical geomechanical issue associated with the top coal caving method. A discontinuum method has been used for comprehensive modeling of LTCC operation by using the Universal Distinct Element Code (UDEC). In addition Particle Flow Code (PFC) and Phase2 were used as support for the caving mechanics analysis. Although the previous researches of gravity flow in caving operations neglected the effect of continuous span expansion, it has been observed in this study that face advancement has a great impact on roof symmetrical behavior. The amount of symmetry fluctuates between different face distances. Horizontal displacement seems to be the best indication for roof symmetrical evaluations. Two critical caving conditions have been modeled and parameters such as horizontal displacement, caving angle and recovery rate have been compared thoroughly. Results show that unsymmetrical behavior on the roof is closely related to face stability.

Jan 1, 2007

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957