Search Documents

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By A. D. Hahn

The Federal Bureau of Mines examined ilmenite-bearing sands in southern Texas as part of a program to discover sources of supply for the domestic titanium industry. Deposits were examined from May 1956 through January 1959 in the outcrops of sandstone beds in the Jackson group of Eocene formations in Lee, Burleson, Fayette, and Starr Counties on the Gulf Coastal Plain; in alluvial valley fill in Brewster County in southwest Texas; in the sand beaches of Matagorda Peninsula and the Galveston, Padre, and Brazos Islands--part of the offshore chain of barrier islands along the Texas coast; and in unconsolidated sediments in Willacy County on the Rio Grande delta in the southeast Texas.

Jan 1, 1961

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017

By Jan Boon

"El presente texto describe el nuevo enfoque empleado en la Responsabilidad Empresarial (RSE) en la minería puesto que retoma el control de la agenda paralelo al crecimiento de poderosos ""descertificadores"" de la sociedad civil y la presión de los gobiernos y organizaciones internacionales como el OECD, las Naciones Unidas, entre otras. Además de las firmas que se especializan en RSE, muchas empresas de desarrollo organizacional y legal, así como empresas de consultoría en temas de gestión, estánincorporando un componente de RSE a los servicios que ofrecen y cada vez más y más compañías publican comunicados de RSE, protocolos de RSE. "

Jul 1, 2012

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By Judith L. Bolis

The Bureau of Mines estimated the potential availability of iron ore from 129 domestic and foreign mines and deposits in 25 market economy countries. The availability of four products on a total and regional basis was determined from demonstrated resources of 75.3 billion It. From the resources evaluated there are a total of 18.6 billion It of sinter fines, 4.9 billion It of lump ore, 14.7 billion It of pellets, and 820 MMlt of pellet feed potentially available at a 15-pct DCFROR, f.o.b. port. On a regional basis, at or below a total cost of $0.26 per iron unit there are 1.7 billion It, 2.8 billion It, and 186 MMlt of sinter fines potentially available from Brazil, Australia, and Africa, respectively. There are 825 MMlt of lump ore from Brazil and 1.4 billion It from Australia potentially available at or below a total cost of $0.24 per iron unit. There are 2.1 billion It of pellets potentially available from the United States at or below a total cost of $0.80 per iron unit, while 442 MMlt are potentially available in Brazil at or below $0.38 per iron unit. South America has 208 MMlt of pellet feed potentially available at or below a total cost of $0.28 per iron unit. While the resources of iron ore are more than adequate to satisfy demand, the future of the iron ore industry is very dependent upon changes in the world economy, and on the domestic scene, changes in the domestic steel industry and steel imports.

Jan 1, 1987

By George A. Komadina

The Pima Mining Company lies 20 miles southwest of Tucson, Arizona, and some 45 miles north of the Mexican border. The mill is situated on a hillside overlooking Tucson and the Santa Cruz Valley, the ground generally sloping northeast at a 2.5 percent grade. The hillside location allows for gravity flow generally through the plant as well as for: tailing disposal.

Jan 1, 1965

By Bowen Li, Canhua Li, Mingsheng He

Steelmaking slag is a by-product in considerable volume and a valuable material for various applications. In general, steelmaking slag is an alkaline compound of CaO, Fe2O3, and SiO2. However, its characteristics varies depending on the feedstocks, steelmaking process and cooling method of the slag. To utilize this by-product effectively, this study investigated the characteristics of steelmaking slags taken from Wuhan Iron & Steel Co. Ltd. The results showed that the slags mainly consist of the oxides of calcium, iron, and silicon, with low contents of magnesia, alumina, and manganese oxide with a feature of high alkalinity and lime saturation factor. The major mineral phases include belite, calcium ferrite, calcium hydroxide, wustite, quartz, and small amount of elite. Thermogravimetric analysis indicated the weight loss from ambient temperature to 800 °C is 8% in total. Melting test showed the glass transition temperature is between 1300 and 1350 °C, flow temperature is about 1400 °C. The slag samples investigated in this study can be considered as a typical glass-ceramic composite.

Mar 1, 2018

By G. B. Harris

Much has been written over the past decade concerning the disposal of arsenic from metallurgical processes. In Canada, there are proposed regulations which would classify arsenic in the Primary Group of twenty one persistent, toxic pollutants to be banned or phased out. Since many nickel and cobalt ores, not to mention those of copper, gold and uranium, contain significant amounts of arsenic, it is pertinent to assess the current state-of-the-art of its disposal. The literature is reviewed, and it is demonstrated that from a purely chemical point of view, the family of ferric arsenates largely immobilize arsenic. There is clear evidence from laboratory studies that both crystalline ferric arsenate (scorodite) and amorphous ferric arsenates in which the molar Fe/As ratio is at least three (Fe/As = 3) have very low arsenic solubility; plant data are given to support this. The debate over the long term stability of these compounds continues however; the evidence presented for long term stability and for compound breakdown is critically reviewed in the light? of the recent structural studies, and the role of base metals in these compounds evaluated. Finally, conclusions are drawn as to the viability of a purely chemical process for the long term disposal of arsenic from metallurgical processes.

Jan 1, 1993

By C. H. P. Lupis, Henri Gaye

There are m -I conditions for the stability of a solution of m components with respect to infinitesinzal flucturations. However, in most cases, only one of these conditions has to be considered to determine the domain of instability and the existence of this more restrictive condition greatly simplifies the calculations. It may be used advantageously for the prediction of miscibility gaps and the method is illustrated in details for the case of the Ag-Pb-Zn system. THE thermodynamic conditions for the formation of a miscibility gap may be viewed as a necessary consequence of the conditions for spinodal decomposition. A previous article1 has examined in detail the form of these conditions for multicomponent systems. There is only one condition for the stability of a binary system (with respect to infinitesimal fluctuations), but there are two conditions for a ternary system, and m — 1 conditions for an m-component system. The probability of violating a stability condition, and thus forming a miscibility gap, obviously increases with the number of components, a result which is rather intuitive since the atoms of the solution have now many more ways of redistributing themselves and introducing complexities in the form of the free energy hy-persurface. It is of interest to take advantage of this possibility of precipitating new phases and to examine which stability condition is the likeliest to be violated, that is, which stability condition is thermodynamically the most restrictive. The finding of such a condition would greatly simplify the application of the stability criteria since only one condition could then be considered, instead of m - 1. In Ref. 1, coherency strain energy terms were neglected, thus restricting the applications of the treatment to solutions where they are negligible, such as liquid alloys. In the following study the same assumption will be made. To generalize the treatment to systems where the strain energy terms are sizable, the reader is referred to Cahn's classical article on spinodal decomposition.2 Let us designate by Gij the second derivative of the Gibbs free energy with respect to the number of moles ni and n j. There are several equivalent sets of m — 1 stability conditions.' The one considered here expresses that the successive diagonal determinants of order 1, 2, ... m — 1, associated with the symmetric Gij matrix (for 2 5 i, j 5 m) are positive.' For a binary solution 1-2, the condition for stability is: O(u=G22^0 [1] For a ternary system 1-2-3, the condition [I.] is re- tained (the value of G22 will differ, of course, according to the concentration of 3) and another condition is introduced: £>(21 = G22G33 - Gl3 ^ 0 [2] In a composition diagram, these two conditions define two domains of instability. Starting at a point where the solution is stable (for instance at a point where the solution is very dilute) we gradually change the composition until the condition [I] or [2] is violated. As already noted in the literature, e.g., in the work of Prigogine and Defay,3 it is the boundary of the domain (2) which is first crossed. For if we assume that the boundary of the domain (1) is reached first, at this point G22 = 0 and the second condition is necessarily violated (D(2) = -& 5 0), in contradiction with our original assumption. An exhaustive study of the ternary regular solution case may be found in the work of Meijering.4 Moreover if the boundaries of the two domains have a common point, they also have a common tangent. For if the two lines were to cross each other as is illustrated in Fig. 1(a) any point M in the line QP would be such that £> = 0 and 0"' > 0 which, as shown above, are incompatible results. Thus, the two lines must be tangent at their common point Q as illustrated in the example of Fig. l(b). The reasoning of Fig. l(a) implies that the point Q is not a "singular" point for either boundary line. This singularity may be of two types. First, the lines meet without crossing each other and without being tangent. Second, the tangent at Q for D"' or 0"' is not single-valued. Other types of singularity are unlikely because of the usual analytical forms of D"' and 0"'. The exception to the common tangent requirement due to the first type of singularity was pointed out by John Morral;5 it occurs when the common point, Q' or (3" in Fig. l(b), is located at a boundary of the composition diagram, e.g., at the line X3 = 0. It may also be noted that at the common nonsingular point Q of D(1) and D(2), Fig. 1(b), G23 is necessarily equal to zero, whereas at a point such as Q' or Q", this conclusion is no longer valid because the product G22G33 is now indefinite (of the form 0. a). The exception to the common tangent requirement due to the second type of singularity occurs when two branches of the same boundary line intersect, for example when D(1)or D(2) decomposes into a product of functions, at a point which belongs to the boundary of the other condition. It is possible to show by a simple analytical calculation that, in this case, if Q is a singular point of D(1), then it is necessarily a singular point of D(2), and that the reciprocal is true except if G33 = 0 at Q. For the present article, however, more elaboration on these singularities appears to be unwarranted. To generalize the previous results to an m -component system, we use the mathematical theorem stating that if the diagonal determinant D(r) = 0, then

Jan 1, 1970

By E. G. Charlesworth, M. J. Robertson

"Abstract - Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots.Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confined largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semi­ massive sulfides within tension fractures which are folded, attenuated and fractured .An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Duane L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry and presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a United States Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) utilizes the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package utilizes a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgement scheme that provides an effective method of identifying problem areas which may exist in the mine network. The package was written in Fortran for a 64 kilobyte, Z80-based microprocessor-computer.

Jan 1, 1984

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990