Search Documents

Chalcopyrite concentrate was combusted in oxygen-nitrogen atmospheres, the composition of which ranged from 1-100 per cent oxygen. Factors studied included particle size, experimental temperature and oxygen concentration. The study was assisted by chemical and X-ray diffraction (XRD) analysis and temperature measurements of single particles. Size reduction occurring after melting was found to have a major effect on the overall reaction time. Thus time to attain ignition was largely determined by the original particle size, whereas combustion time was independent of this factor. For particles larger than 40 I'm in air the time to attain ignition predominated. The maximum temperatures measured for single particles were the result of pyrite present in the concentrate. Chalcopyrite did not attain thesame temperatures. Vaporization, either as CU(g) or CuO(g) lImited the temperature. Maximum temperatures measured for single particles of pyrite ranged from 1610°C in 14 per cent oxygen to 2360°C in 100 per cent oxygen (both at 700°C). Measured temperatures were compared with those calculated from a diffusion-based model.

Jan 1, 1983

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

Development on the North Kalgurli mine has established a major penetration of ore into calc schist. This is controlled by a system of east-dipping strike faults. Previously, most calc schist ore bodies were regarded as being confined to the quartz dolerite greenstonecak schist contact environment.INTRODUCTIONOne of the most interesting and economically important developments which has taken place in the Kalgoorlie Field over the past 20 years is the proved penetration of ore into calc schist on the North Kalgurli Mine. This is quite extensive, both laterally and in depth, and has occasioned some modification of geological thought in the search for additional ore sources.Ore has been mined in calc schist almost since the first major gold discoveries were made and the principal features of the various types of deposit are well covered in the literature of the field. However, occurrences in calc schist have not been characterised by the same degree of continuity or frequency as the innumerable lode formations in the more favourable quartz dolerite, and there has been a tendency to regard them as isolated and discontinuous ore bearing structures, occurring only under very special conditions.It is not intended to describe the whole range of calc schist ore occurrences but only major controlling structures, whose penetration therein has been definitely established and in which an appreciable amount of ore has been and is still being found. It is considered that similar structures may present a major objective for future exploratory work in other parts of the field.

Jan 1, 1964

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By E. Stoetzer

In all known deep mixing processes the existing soil is mixed with self hardening slurry by mixing tools that rotate about a vertical axis (augers, mixing paddles). Wall panels are constructed using sets of multiple mixing tools combined into a single unit. These techniques have been developed on the principle of the rotary drilling technology. In contrast, the new Cutter Soil Mixing or CSM technique is derived from the cutter technology. The soil is loosened and broken down by cutter wheels, then mixed in-situ by the rotating cutter wheels with the self-hardening slurry - introduced into the ground between the two wheels - to form a soil-slurry mortar. The main area of application lies in the construction of cut-off and retaining walls.

Jan 1, 2006

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

By Peter White

A bridge reconstruction project involved driving pipe piles for the new foundations. Disturbances within soil layers at depth caused sinkholes to open up within the construction site. After a near fatal accident, the pile driving installations were suspended. The solution involved ground im­provement through cement grouting with sleeve pipes and special grout additives to minimize migration of cement grout.

Jan 1, 1997

Urban development to the south of Sydney is approaching areas of current and proposed coal mining. Already some structures and residential areas are affected by mining subsidence.Subsidence resulting from either conventional pillar extraction methods or longwall mining has been monitored for 15 years to enable the characteristics of the surface deformation to be determined.The vertical and horizontal displacements of survey stations on the surface are monitored and the results arc used to calculate subsidence, changes in slope of the surface, curvatures along the subsidence profile, and the ensile and compressive strains. These features are in turn related to the underground extraction to give a description of surface subsidence and the development of subsidence with time.Subsidence investigations have been carried out over all or part of the workings of six collieries in the Southern Coalfield.Two case histories illustrate the procedure in the investigation of subsidence phenomena. The first example is the study of the subsidence over a series of longwall panels in one seam and the second is a study of subsidence over pillar extraction in two seams one above the other. From the results of the investigations the effects of panel widths on subsidence are determined.This and other information assists mine planning in areas where surface movement and deformation are important considerations.

Jan 1, 1980

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011