Search Documents

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By Xuling Chen, Zhiyun Ji, Min Gan, Wenqi Li, Xiaohui Fan, Zhiyuan Yu

"Specularite and vanadium-titanomagnetite are difficult to granulate, and with the increase of their proportions, the permeability of sintering bed is deteriorated together with the combustion velocity of fuel for the shortage of air through the sintering bed, which can lower sintering speed and specific production capacity significantly. The biomass fuel has a higher combustion velocity than coke breeze, therefore the productivity of specularite and vanadium-titanomagnetite ore can be improved remarkably by replacing coke breeze partly with biomass fuel .The results showed that, when the proportion of biomass fuel replacing coke is 40%,the sintering speed and specific production capacity of 35% specularite were improved from 19.06mm/min, 1.33 t/(m2·h)to 21.45mm/min, 1.47 t/(m2·h),and that of 55% vanadium-titanomagnetite were improved from 17.23mm/min, 1.11 t/(m2·h)to 22.80mm/min, 1.44 t/(m2·h). As a conclusion, biomass fuel is effective to strengthen sintering of refractory iron ore.IntroductionThe iron and steel industry of our country has achieved significant development in the recent years. In 2010, the output of steel has reached to 0.627 billion tons. The increasing scale of iron and steel has led to rigorous domestic iron ore environment, and the reserves of hematite and magnetite that have superior sintering characteristics are on the decline with continually exploiting and utilizing [1]. Therefore, the RIO (refractory iron ores) SP (specularite) and VT (vanadium-titanomagnetite) have to be applied vastly. However, the quality of sinters can be deteriorated when utilizing RIO in high proportion due to their poor granulation and metallogenic performances [2, 3]. Generally, the ratio of SP is 3~5%,which should not exceed 10% in our country currently [4]. Though high rate of VT is adopted in PZH steel for a long time, the productivity is obviously low compared with normal sintering [5]."

Jan 1, 2012

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By Lassi Klemettinen

For better understanding and maximal value utilization of the WEEE smelting process, the behavior and distribution of different trace elements must be known. In this study, the behavior of nickel as a trace element was studied in an equilibrium system with metallic copper—spinel saturated iron silicate slag (with 3 wt-% K2O)—iron aluminous spinel—gas. The experiments were conducted in alumina crucibles at 1300 °C, in oxygen pressure range of 10−10–10−5 atm. A time series of 15–60 min experiments was also conducted for investigating the formation rate of the primary spinel phase in the system. The results show that the distribution coefficient of nickel between metallic copper and liquid slag changes from approximately 70 to 0.4 along the increasing oxygen pressure range. In addition, a significant part of the nickel deports into the spinel phase. The spinel formation was investigated based on composition analysis results and visual observations from SEM-images.

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By Linlin Tong, Xiangling Song, Guobao Chen, Zhenan Jin, Hongying Yang

Biooxidation of a high arsenic-bearing refractory gold ore was investigated to determine the arsenic removal efficiency by the cultured bacteria and to examine the effect of biological pretreatment on subsequent gold cyanidation. The biooxidation pretreatment process utilizes the ability of adapted acidophilic bacteria to oxidize pyrite and arsenopyrite and release the encapsulated gold. The released gold can be efficiently extracted by the subsequent cyanidation process. The biooxidation experiments were conducted with cultured bacteria using various sizes of agitation tanks. Leaching results showed that over 96.26 % arsenic extraction could be obtained from this ore after 6 days of bioleaching with continuous stirred tank reactor (CSTR). Gold extraction during the cyanidation process was increased from 29.35% to 96.71% after biological pretreatment. The content of arsenic in the biooxidation residue was reduced to below 0.3%. The transformation process of As was considered as [AsS]2- ? As (?) ? As (?) during the biological pretreatment.

Jan 1, 2014

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to high-grade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to highgrade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By O. V. Suvorova, V. G. Minenko, D. V. Makarov, A. L. Samusev, E. A. Selivanova

"Saponite is a valuable marketable product widely used foundry, metallurgy and construction, in the chemical, food and consumer goods industries, in medicine, and in agriculture.The feasibility of producing of high-quality construction materials with enhanced physical-chemical and decorative characteristics from saponite-containing products has been given a scientific basis and experimentally validated. The compressive strength of the samples in the sintering temperature range of 800-1000 ?? varied between 35 and 80.9 MPa; the bending strength 8 and 26.7 MPa, which is superior to the high-grade ceramic bricks of the M-300 brand. It has been established that the saponite-containing product obtained using the electrochemical separation of process water has a high sorption capacitance relatively the heavy-metal ions such as nickel and copper (40.7 and 99.8 mg/g, respectively). As a result of sintering at 750 ?? the sorption capacity of the sorbent for the nickel and copper ions increased to 194.2 and 212.8. Using the XRD and SEM with energy-dispersive spectroscopy studies, we diagnosed the metal-containing phases and validated the metal sorption mechanism.This study opens up the possibility of practical realization of the saponite-containing product as high-quality building materials and heavy-metal sorbents while addressing the issue of process water treatment. INTRODUCTION The Lomonosov deposit of the Archangelsk diamondiferous province accommodates 10 kimberlite pipes. The anticipated volume of diamond-bearing ore and dump rock to be removed before reaching the open-pit mining limit is 300 mln t (Karpenko, 2009; Bezborodov, etal. 2003). Rock in the deposit is almost completely displaced by clay minerals, predominantly saponite, amounting to 90% in the vent facies (Karpenko, 2009)."

Jan 1, 2018

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008