Search Documents

By Luis v. Coppa

Since its inception in 1910, the Bureau of Mines has been the principal Federal agency involved in ore reserve estimations, using such traditional methods as polygons of influence and variations of inverse distance weighting While adequate for estimating the average are grades in a mining block or section, these methods do mot, however, provide a consistent way of quantifying the reliability of the estimates. This report describes a technique for enhancing ore reserve estimations using geostatistics, the methodology of which combines the spatial and random aspects of geologic phenomena into a formal theoretical framework for deriving the estimation variance of ore reserves. Correctly used, geostatistics enables confidence intervals to be placed around ore reserve estimates calculated from drill hole data. A geostatistical software system was obtained -From the U.S. Geological Survey and installed, aster slight modifications, on the Bureau's Wang computer. System testing and validation was conducted using a simple cast-book-type example. This was then followed by variogram analysis, point kriging and block kriging of data from a previously worked section of a uranium mine.

Jan 1, 1984

Jan 1, 1970

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By J R. Leeming

Mines require ventilation to ensure an adequate atmosphere for the sustenance of life, and to dilute, render harmless and remove contaminants.This paper describes the developments in the United Kingdom (UK) from natural ventilation, through the introduction of fire and simple fans, to modern fully independent and remotely monitored and controlled installations.CITATION:Leeming, J R, 2017. The history of mine ventilation in the United Kingdom, in Proceedings Australian Mine Vent Conference 2017, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is he ted above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that tallow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009

By Dennis R. Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson’s effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By J. David Gunn, Richard W. Lawrence

Gold and silver often occur finely disseminated in sulphide minerals such as pyrite. The use of biological leaching to dissolve pyrite and liberate gold has been extensively studied for a concentrate from the Porgera deposit, Papua New Guinea. The successful operation of a continuous bioleach circuit has been demonstrated. Bioleach residues were cyanide leached to extract gold and silver, and unreacted pyrite recovered for recycle to the bioleach. A 26 day steady state continuous bioleach test on a concentrate assaying 14.3 g/tonne Au and 87.0 g/tonne Ag produced residues with an average 73.5% weight loss and a pyrite oxidation of 88%. Cyanidation and recovery of pyrite from the cyanide residues for recycle gave overall recoveries of 92.1% gold and 74.6% silver. A proportion of the remaining precious metals was found in the bioleach solutions and may be recoverable. Losses to tails were 3.0% gold and 8.1% silver. Final tails represented 14.3% of the feed weight and averaged 1.84 g/tonne Au. A description of the continuous bioleach circuit and bioleach residue handling procedures, and the results of the study are presented. The features and advantages of biological oxidation as a pretreatment for refractory precious metal ores and concentrates are discussed.

Jan 1, 1985

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By M. Hakala, P. Tolppanen

A method to predict stress-induced failures around excavations based on the mapped geological and rock mechanical information is studied. Totally of 7 km of newly excavated tunnels are mapped in the Inmet’s Pyhäsalmi mine in Finland at depth between 1000 - 1440 m from which the results and conclusions from the firstly mapped 1.7 km of tunnels are reported. The main rock type at the site is very hard volcanite having uniaxial compressive strength of 230 MPa in median and GSI-value 72 - 80. The maximum in situ stress around the tunnels is 65 - 85 MPa. The prediction of observed stress failures was preceded by comparing elastic 3-D simulation results of tunnels with three statistical yield criteria. Read’s or Hoek & Brown’s yielding criteria are found the most relevant, though, the effect of anisotropy was found to be significant. The most important parameters having a correlation with stress failures are the tunnel orientation and the foliation of rock. Also, the rock type and its strength, tunnel shape and the geological anomalies have their effects. Further, a delay time on mapping was found to clearly diminishing of the most violent failures. Une méthode de prédiction des contraintes à la rupture autour d'excavation, établie sur la base de cartographie géologique et d'information sur la mécanique des roches, à été étudiée. Au total, 7 km d'un tunnel nouvellement percé à une profondeur de 1000 à 1400 m ont été cartographiés dans la mine de Inmet’s Pyhäsalmi en Finlande. La roche principale du site est une vulcanite dur ayant une résistance à la compression uniaxiale de 230 MPa (valeur moyenne) et une valeur GSI de 72 - 80. La contrainte in situ maximale autour du tunnel se situe entre 65 et 85 MPa. La prédiction des contraintes à la rupture observées a été évaluée en comparant les résultats d'une simulation 3D d'un tunnel avec trois critères de limite d'élasticité statistiques. Le critère de limite d'élasticité de Read ou de Hoek & Brown’s se trouvent être les plus important, même si les effets de l'anisotropie sont significatifs. Les paramètres les plus importants ayant une corrélation avec la rupture sont l'orientation du tunnel et la foliation de la roche. De plus, le type de roche et sa résistance à la compression, la forme du tunnel et les anomalies géologiques ont aussi leur importance. Finalement, un délai dans la cartographie résulte en une diminution nette des ruptures violentes. Basierend auf kartierten geologischen und felsmechanischen Informationen, wird eine Methode untersucht, um spannngsbedingtes Versagen um Ausbrüche herum vorherzusagen. Insgesamt werden 7 km neu ausgebrochenen Tunnels in einer Tiefe zwischen 1000 und 1400 m in der Inmet Pyhäsalmin Mine in Finnland kartiert. Das hauptsächlich vorkommende Gestein ist sehr hart und vulkanischen Ursprungs mit einer mittleren einachsialen Druckfestigkeit von 230 MPa (Medianwert) und einem GSI-Wert von 72-80. Die maximale In-situ-Spannung im Tunnel beträgt 65-85 MPa. Die Vorhersage von beobachteten Spannungsversagen werden weitergeführt indem man elastische 3-D-Simulationsergebnisse von Tunneln mit drei statistischen Fliesskriterien vergleicht. Read's oder Hoek's Fliesskriteria werden dabei als die relevantesten Kriterien angesehen, obwohl auch der Effekt der Anisotropie als wesentlich erachtet wird. Die wichtigsten Parameter für eine Korrelation von Spannungsversagen sind die Orientierung des Tunnels und die Schieferung der Gesteinsschichten. Desweiteren haben Gesteinsart, Tunnelprofil und geologische Anomalien ihren Einfluss. Ausserdem zeigt sich, dass eine Verzögerung bei der Kartierung die ausgeprägtesten Versagen deutlich verringern.

Jan 1, 2003

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962