Search Documents

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By Avery H. Reed

RECORD production of crude petroleum, lime, crushed marble, and talc highlighted the mineral industry of Alabama in 1963. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 86 percent of the total value of production, compared with 82 percent in 1962. The iron-ore industry continued to decline; in 1959 the value of iron ore produced was 12 percent of the total State production value; in 1960, 11 percent; in 1961, 10 percent; in 1962t 8 percent; and in 1963, 5 percent.

Jan 1, 1964

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By M. Oliverio

The Cigar Lake uranium deposit was discovered in 1981 at the south western end of Waterbury Lake, approximately 660 km north of Saskatoon in the province of Saskatchewan (see Figure 1). It is the largest undeveloped high grade uranium deposit in the world. It contains proven and probable reserves of more than 226 million pounds U3O8 at an average grade of 20.7%. The world average grade is less than 1% U3O8. [ ] The ore body is located about 450 m below surface at the interface between sandstone above and basement rock below (see Figure 2). The sandstone is fractured rock and saturated with water. This makes water inflow a real hazard at the mine. In fact there have already been two significant mine inflow events. The first of these occurred in October 2006 and resulted in the flooding of the mine. The second occurred in August, 2008 during mine recovery activities.

Jan 1, 2011

By M. A. Barclay, D. Samson, A. M. Esteves

Several companies have adopted policies and standards aimed explicitly at increasing ‘local procurement’, recognising that local economic participation has benefits for companies and communities alike. From a corporate perspective, local economic participation is seen as one means of maintaining a social license to operate, as well as ensuring reliability of supply by having a supplier located nearby. From a community perspective, the participation of local businesses in the resource project is a means by which the benefits of resource development can flow into their communities. This paper is based on the research undertaken to produce a good practice guide for the mining, oil and gas sector. Our research revealed that the extent to which the local community will actually benefit from local procurement initiatives is dependent on the capacity of the community to supply goods and services to the project and, even more importantly, on its ability to adapt to the inevitable changes that accompany large-scale resource development. We provide guidance on adapting impact assessment tools to guide planning of procurement interventions.

Jan 1, 2011

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006

The lignite resource in the southern part of the South Island is New ZealandÆs largest source of indigenous primary energy. The ten deposits evaluated by the Liquid Fuels Trust Board (LFTB) have a total recoverable reserve of 6.2 billion tones equivalent to 74 000 PJ of energy or 20 times the original energy content of the Maui gas field. Updating the economics of the original LFTB studies indicates that lignite could be mined for between NZ$1.0 and 3.0/GJ. Its conversion to synthesis gas for production of petroleum products, chemical methanol, ammonia/urea fertiliser or electricity would be in the national benefit and likely to be commercially economic at todayÆs product prices.

Jan 1, 2005

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

Thermal method of diagnostic as a nondestructive monitoring is based on data logging of infrared radiation from heated surface or from the associated thermal field. Monitoring of gearcases and motors hidden faults, such as, bearing degradation (deep-seated wears and tears, fretting wear, spalling and jamming solids of revolution) is closely related to high variations in temperature. The use of portable thermal imaging devices provides considerable advantages due to: easy remote access to the unit under test even when it is operating; minimum time required to obtain information and an opportunity for a real-time diagnosis of the tested subject's condition.

Dec 6, 2010

By M E. Dunphy, P Silversmith

The Reefton Goldfield, both historically and potentially, represents a significant gold producing camp in the Westland province of New Zealand. Some two million ounces of gold have been produced from the Greenland Group host rocks between 1870 and 1951 with the most significant producers being the Blackwater and Globe Progress mines.   Steep terrain, high rainfall, poor outcrop, widespread fluvio-glacial deposits, tertiary cover and sometimes onerous environmental access conditions have proved a challenge to conventional exploration techniques. In addition classic exploration techniques have come up against a desire to reduce exploration cycle time and exploration costs while increasing both quality and quantity of geological information.   The trial, and subsequent implementation, of Wacker sampling has proved a highly successful and effective geochemical tool currently being utilised to target, discover, and define potential economic gold mineralisation in the Reefton Goldfield.

Jan 1, 1997

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By J J. J Chen, J C. Zhao

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions. Metal refining is most efficient when fine bubbles are generated and uniformly distributed within the treatment tank. The application of some measuring technique able to detect this distribution within a non transparent operating treatment tank would be invaluable, enabling the optimisation of gas flow and impeller speed.   A technique has been developed to measure the pressure fluctuation levels at specific points in the water model. Comparison of these pressure fluctuation data with photographic evidence obtained in the water model suggests that the flow regime in the metal treatment unit may be determined using this technique.

Jan 1, 1995

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change.   The aims of this paper are to: +        outline alternative types of mining contracts, as well as their strengths and pitfalls; +        describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +        identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

By G. M. J. van Heerden, R. C. W. Webber-Youngman

"This article describes the re-engineering principles applied in the design of a personnel transportation system for the Bafokeng Rasimone Platinum Mine in the Rustenburg area of South Africa. It incorporates conveyor belt travelling, chairlift operation, and also includes consideration of proposed changes/modifications to the existing conveyor belt infrastructure.The purpose of the project was to identify, through a process of evaluation, the appropriate option and/or combination of transportation options that would be safe in terms of personnel transportation as well as cost-effective. Alternative measures for transporting personnel (not using belt riding) would have a significant positive spin-off, increasing the availability of the belt and thereby increasing production. This paper explores the feasibility of interventions that would improve safety through eliminating risk associated with personnel transportation as well as contributing towards improving the mine’s position on the cost curve.The design in consideration at the Bafokeng Rasimone Platinum Mine consists of two shaft systems, namely the North Shaft and South Shaft, each comprising twin decline shafts. One of the decline shafts is equipped with a conveyor belt for rock and personnel transportation, and the other with a winder for trackbound material transport. The conveyor belt has been used for personnel transportation since the commissioning of the shafts. The conveyor belt is equipped with platforms for personnel getting off and on the belt and a number of safety devices designed to ensure safety while travelling on the belt. Intensive training in the practical aspects of belt riding is given to every person, and unsupervised riding on the belt is permitted only once belt riding competence is demonstrated. Despite this, the safety results were poor, with 106 injuries between 2006 and May 2013. Fortunately, no fatalities were reported during this period.An investigation of alternative means for personnel transportation or engineered solutions to the current conveyor belt infrastructure in the safest, most effective, and most economical way was therefore needed. There was a major risk of safety-related stoppages being imposed following another belt accident/incident. This would prevent the mine from transporting personnel underground by belt and result in major production losses. From the commissioning of the Phase 2 shaft deepening project on both shafts, dedicated chairlifts have been used for personnel transportation as opposed to the conveyor belt installed in the Phase 1 area. The chairlifts have been in operation since 2004 and no chairlift-related incidents have been recorded thus far. According to safety statistics, it is clear that the chairlift is the safer method for the transportation of people in the shaft.To fulfil the objectives/scope of this study, it was recommended that both primary (new chairlift decline with infrastructure) and secondary options (modifications to the current conveyor belt infrastructure) be considered for implementation on both the North Shaft and South Shaft to reduce or eliminate accidents/incidents as a result of belt transportation. The associated capital expenditure would be approximately R200 million. Considering the future impact on the business as a whole, this would definitely be capital well spent."

Jan 1, 2016

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013