Search Documents

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By Víctor Cárdenas

El presente trabajo describe el manejo de las herramientas de calidad que aportan a la reducción de riesgos en la compañía minera La Poderosa. Para determinar los defectos, causas y consecuencias, es necesario conocer el procedimiento de control de los mismos a través del diagrama de Ishikawa o el ciclo de PHVA. Esta metodología permite encontrar la solución a los problemas dentro del aseguramiento de la calidad, seguridad y productividad de una empresa, así como establece la fuente de la causa de los accidentes por lesiones, como de los daños a la propiedad privada. En consecuencia, su aplicación se ha estandarizado en las áreas de seguridad y medio ambiente de dicha minera desde hace dos años, obteniendo resultados muy satisfactorios como el Premio Nacional de Seguridad en minería subterránea otorgado por el ISEM.

Sep 13, 2001

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure'acid leaching.

Jan 1, 2002

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By J. W. Thompson

The term "minerals" when employed in a conveyance in the State of West Virginia is understood to include every inorganic substance which can be extracted from the earth for profit, whether it be solid, as rock, fire clay, the various metals and coal, or liquid, such as salt, and other mineral waters and petroleum oil and gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. TERM INCLUDES OIL AND OAS. The term "minerals" used to describe the interest in land granted or reserved bona fide includes petroleum oil and natural gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. INJUNCTION TO PREVENT RElllOVAL. The removal of ore from the premises of another without his consent will be enjoined. Barnes v. Esch (Oregon), 169 Pacific, 512, p. 518. TITLE TO MEXICAN BULLION-JURISDICTION OF FEDERAL COURTS TO DETERMINE. Where bullion within the jurisdiction of the Mexican Government was seized, condemned, and sold for war supplies by the Constitutionalist forces in the revolution acting under authority from Gen. Carranza, claiming to be the provisional President of the Republic of Mexico, a United States district court of Texas, into which State the bullion has been imported from Mexico, has jurisdiction to try and adjudge as to the validity of the title acquired by and through the seizure, appropriation, and sale by the Carranza forces as against an American citizen claiming ownership of such bullion prior to its seizure.

Jan 1, 1919

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

By Frank B. Fulkerson

Barge traffic on the Nation's inland waterways over the past 15 years has been increasing at a rate much faster than intercity freight traffic by all modes, largely due to the growing consumption of mineral commodities, development of more powerful towboats and large and more specialized barges, improvements to loading and unloading facilities, and competition among bargelines for contract shipment of bulk commodities. The Bureau of Mines, in a study to determine barge traffic projections for inland waterways in the South-Central States to the year 1980, gathered data on origin-destination patterns by commodity, quantity moved, equipment used, and rates charged; the trend of each of these factors over time; and the extent of competition between water trans-port and other means of transportation. The Mississippi River and the Gulf Intracoastal Waterway, which together carryover half the Nation's barge traffic, are major carriers of coal, crude petroleum, steel, marine shells, sulfur, salt, cement, and alumina. Greater quantities of these products will be transported by barge; however, oil pipe-lines and unit trains for coal are expected to limit increased barge traffic of these two commodities. Increasing quantities of fertilizer materials will be transported upstream. Although congestion at certain locks is a current problem, the Mississippi River below St. Louis and other open-river stretches have the capacity to handle the increasing number of barges for the foreseeable future.

Jan 1, 1969

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

On a worldwide basis trackbound transportation is on the decline. As mining operations progress from open cast operations to underground operations, most utilise mechanised equipment. However, in South Africa hard rock mines, only a small percentage (¦10 per cent) of the production can be generated by mechanised methods and therefore trackbound mining methods will remain the dominant means to transport ore. In the Australian context there may be occasions where the nature of the orebody would dictate the use of rail transportation with the ore being transported from drawpoints by means of locomotives and hoppers. This paper focuses on horizontal rail haulage systems from the stope loading boxes to the shaft station area and will be largely based on South African experience. It is intended that this document will provide a practical guideline for mine designers and planners during the design process. The paper looks at trackbound transport systems and evaluates such items as construction and management of an underground rail haulage system. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2005

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Peculiarities of Quartz Distribution in Zinc Flotation Products and their Influence to Mineral Processing

Sep 13, 2010

SAG Mill Grinding Design Versus Geometallurgy - Getting it Right for Competent Ores Smarter processing for the future, in the area of SAG mill design involves accurate grinding test data, completing final mill design in less than three months, and at a cost of less than US$80 000. More detailed variability testing on the other hand takes longer, is more expensive, and is used for throughput optimisation for an existing or newly purchased mill. This paper shows that SAGDesignTM testing is excellent for new SAG plant design due to relatively low cost per test and the ability to do more testing for a limited budget on larger projects. It also briefly examines a way to develop proper geometallurgical ore hardness information on every block in the mine model, from the more detailed analysis data.

Sep 13, 2010

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005