Search Documents

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Beavis FC, Box JC

The important chemical and fluid flow phenomena in heap, dump and in situ leaching are summarised. Published, quantitative models of these processes are critically reviewed, and their potential applications outlined. Comparison between the independent predictions of one of the models and column leach test data reported by others confirms the potential. Some recent developments by the authors in the fields of fluid flow through unbroken ore and modelling of the more complex chemical systems are briefly Described.

Jan 1, 1981

By H. Lyn Bourne

This is the fourth annual tabulation that gives mineral royalty information. The table presents previous information plus about two dozen new entries. In addition to the royalty information, some entries show the cost of purchased reserves. Last year's tabulation appeared in two issues, to accommodate all of the information. This year the format has been changed slightly so the table can be printed in one issue. This year's table presents the commodities in the same sequence as last year. Sand and gravel information appears first, followed by: crushed stone for aggregate; other stone; industrial sand; other industrial minerals; energy minerals (coal, oil shale, uranium); and finally metals. As always, a caveat relates to factors that influence the reserve values. The data should serve only as a general reference. The table is not intended to present an absolute scale of reserve costs. Several factors influence the value of mineral commodities. These factors include: • location and transportation costs (especially significant for most industrial minerals); • market conditions for both the commodity and the company acquiring the right to mine it; • quality or grade of the deposit as it reflects the amount of processing and beneficiation necessary to produce the finished product; • and legislative restrictions and conditions for mining a given material at a given site. These and other factors will influence reserve costs of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity; the location (either by state, US geographic area, or Canadian province); the cost (R for royalty and P for purchased cost); and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cuft), tons (/T) (2000 lbs) or acres (/A). 1 cu yd = 0.76m3 1 cu ft =0.28m3 1st = 0.9 t7 1 acre = 0.40 ha or m2 In several cases the royalty is a percentage of the finished products, sale price and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: J. Dunn, T. Eyde, K. Loda, L. Morgan, F. Nix, H. Sorenson, and L. Williams. Several people have said they would like this to be an annual tabulation. That can happen if new information comes to the writer. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write or call: H. L. Bourne, c/o Neyer, Tiseo & Hindo, Ltd., 38955 Hills Tech Dr., Farmington Hills, MI 48018, (313) 553-6300. Only with new information can this become an annual and current source of reserves costs.

Jan 8, 1986

By Bibhu Mohanty, Sheng Huang

Accurate measure of fragment size distribution is a key objective in all blasting and crushing operations. Several generic distribution functions have been devised to describe the degree of fragmentation for the representative range of fragments from selected measurements. The application of four distribution functions, i.e. Rosin-Rammler, Swebrec, Grady and Gilvarry, in describing fragment size distribution of impact-induced fragmentation of a limestone rock has been investigated. A modified Hopkinson Pressure Bar experimental set-up is used to control both impact velocity and energy input into the target rock. The feed size in the sample holder is varied from 6.35mm to 15.88mm in three ranges and the impact velocity up to 14m/s. The size distribution in the product is determined by sieve analysis for a range of impacts. The experimental results are fitted to the four distribution functions to examine their relative accuracy and reliability.

Jan 1, 2016

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

This report has been prepared in response to a request by the Bureau of Land Management (BLM) Fairbanks Alaska District Office that the Bureau of Mines quantitatively assess the potential supply of minerals from undiscovered deposits in the White Mountains National Recreation Area (WMNRA) and the western part of the North Steese National Conservation Area (SNCA) in Alaska. The assessment will be used to assist in future land-use decision-making. Resource Management Plans (RMPs) for the WMNRA and the SNCA were approved by the BLM in 1986. These plans imposed significant restrictions on new mineral development in the two areas. The level of public concern regarding these actions, especially on the part of the mining industry, has spurred BLM to seek additional information about the potential supply of minerals from the two areas with assistance from the Bureau of Mines. The assessment focuses on an area within the WMNRA and the SNCA which has been administratively closed to mineral entry. The study area encompassed approximately 1.24 million acres and included all of the WMNRA and the western portion of the North SNCA (fig. ES-1). Three quantitative estimates of the potential supply of minerals from the study area were developed: 1) For all lands in the study area, assuming that they are open to mineral entry-the baseline analysis; 2) For those lands which have been closed to mineral entry; and 3) For eleven prospective mineral activity areas, assuming that all are open to mineral entry.

Jan 1, 1989

By Y Xie, L O’Connor, S C. Dominy

Sheeted vein gold deposits are characterised by multiple subparallel veins and often free milling gold. Variability in gold grade and recovery parameters are enhanced by poorly designed sampling and test work protocols. Poor quality samples generally equate to an enhanced nugget effect. A sample can be described as being representative when it results in acceptable levels of bias and precision. Total sampling variability can be quantified by the relative sampling variance, which measures the total empirical sampling variance influenced by the heterogeneity of the lot being sampled under the current sampling / test work protocol. Effort should be made to minimise the relative sampling variance through Theory of Sampling (TOS) and quality assurance / quality control (QA/QC) application. This contribution reports on a case study that exemplifies how high-quality grade and recovery data can be gained from a well-designed and planned drilling, sampling and test work program, followed by bulk sampling. Results across historical resource drilling, geometallurgical drilling, laboratory assay / test work, geometallurgical modelling and a bulk sampling/pilot processing study are reconciled. A whole core, entire-sample test work protocol was used to acquire fit-for-purpose gold grade and recovery data for inclusion into a Pre Feasibility Study reported in accordance with the JORC Code.CITATION:Dominy, S C, O’Connor, L, Xie, Y and Glass, H J, 2017. Geometallurgical sampling protocol validation by bulk sampling in a sheeted vein gold deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 185–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By E. D. Calvert

This Bureau of Mines report discusses the electric-arc reduction of zirconium and hafnium oxides with carbon yielding a metal-metallic carbide mixture. The carbon to oxide ratio in the feed determines the metal to carbide ratio in the product. A sample of this product was produced -or testing as a feed for the deBoer iodide-dissociation process. A new technique for producing pure carbides is described, which uses the intense heat of the arc to volatilize the carbide. The condensed vapor form , crystals of nearly stoichiometric carbide, INTRODUCTION This research examines the preparation of refractory metal carbides in the controlled atmosphere electric-arc furnace.

Jan 1, 1962

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

By Michael B. Cortie

The young field of nanotechnology has as its objective the design and construction of useful devices made of nanoscale materials. Objects or structures which have at least one important dimension in the range 0.5 to perhaps 50 nm may be considered to be in the nanoscale domain. These sizes lie far below the 200 nm or so that can be resolved with an optical microscope, and are closer in size to the 0.3 nm diameter of individual atoms. Nanotechnology, which is the study and exploitation of these tiny structures, is attracting keen interest at present. The excitement is motivated by the observation that control of matter at the nanoscale holds the promise of faster computing, better medicines, and smarter materials. In this paper, the physical phenomena on which this optimism is based are broadly discussed and explained. Where appropriate, examples of the rather different and curious properties of gold at the nanoscale are used to illustrate the points covered.

Oct 1, 2003

Jan 1, 1996

By Sadettin Bagdatli, Ali Kahriman, Umit Ozer, Alper Celtikci, Yucel Karakus

Due to population growth and rapid urbanization in Turkey, the need for the construction of residential units, transportation and infrastructure facilities has become increasingly more pressing. Since rock units encountered in the surface and underground in the construction of the subway, infrastructure and housing facilities, it is a necessity to use blast excavation methods. In recent years, large housing construction projects have been carried out especially in Turkish metropolitan areas, involving foundation excavations giving rise to great amounts of earthmoving. Since rock units encountered during foundation excavations are usually hard and solid, excavation with conventional machinery proves to be inadequate and unproductive, hence the necessity for the application of blasting technology.

Jan 1, 2014