Search Documents

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By S. B. Johnson

Keywords: Spray, Aluminum, Simulation A stochastic, droplet-resolved model has been developed to describe the behavior of a binary aluminum alloy spray during the spray-rolling process. In this process, a molten aluminum alloy is atomized and the resulting spray is deposited on the rolls of a twin-roll caster to produce aluminum strip. The one-way coupled spray model allows the prediction of spray characteristics such as enthalpy and solid fraction, and their distribution between the nozzle and the deposition surface. This paper outlines the model development and compares the predicted spray dynamics to PDI measurements performed in a controlled configuration. Predicted and measured droplet velocity and size distributions are presented for two points along the spray centerline along with predicted spray averaged specific enthalpy and solid fraction curves.

Jan 1, 2005

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Brian Carr

This workshop will display all of the existing products that are available as stemplug devices and discuss the general concept of the use of them. Actual results will be discussed along with several case histories. There will be adequate time for questions and answers.

Jan 1, 2000

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

Taking Up the AFN Corporate Challenge ?? About MAC ?? ?Towards Sustainable Mining? ??Mining and Aboriginal Peoples Framework ?? AFN-MAC Relationship ?? A New MAC Northern Initiative ??Social and Economic Progress ?? A View to the Future?

May 1, 2009

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6) tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of along wall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936

By Kevin Connor

During 1986, the Government continued with efforts to ease the country's almost total reliance on coffee exports for trade revenues by allocating 45% of the Government's budget to commerce and industrial projects. The collapse in coffee prices in 1985 continued to exacerbate the country's growing trade deficit, weakened currency, and dwindling reserves of foreign exchange in 1986. Amoco Burundi Petroleum Corp., a subsidiary of Amoco International Oil Co., continued with plans to drill at least two exploration wells in Lake Tanganyika in 1987. Both offshore and onshore drilling exploration was planned by Amoco Burundi. Any oil or gas finds were expected to have substantial impact on the Burundian economy, as a major portion of the country's trade deficit was directly attributable to petroleum and gas imports.

Jan 1, 1988

By O. J. C. Runnalls

"Canada became the world's largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada's uranium resources will grow because of the foreseen growth in the world's installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988