Search Documents

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine&apos;s history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

By P R. Denize, V S. Wein

A brief review of the Waipipi Iron Sands Limited company history and operations over the past ten years is made along with a summary of the benefits of this mining company to New Zealand. Land rehabilitation procedures in coastal dune lands are described in detail and brief mention is made of a study of animal health and copper uptake. The paper concludes with a summary of the increased emphasis on agronomy and restoration as the mining operation commences dredging in a better class of grazing land.

Jan 1, 1981

Coal has become an enormously important export industry. Owing to a range of mainly natural advantages, Australia has been able to almost treble its exports in a little over the last decade. Australia is now the world&apos;s second largest exporter and coal is now the nation&apos;s largest single export earner.Despite this very significant growth, Australia&apos;s competitive position is in jeopardy.

Jan 1, 1984

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

It has long been recognised that Australia can benefit substantially in an economic sense from its rich resource base. The significant resources of the Gippsland Basin are a good example of the wealth of this nation. As cited in popular debate, Australia must value-add to its natural resources to ensure its long term economic prosperity. The significant oil, gas and coal resources of the Gippsland Basin have provided the Strategic Research Foundation with the basis for two major research and development initiatives ensuring the long term economic development of the Basin and Australia. The gas and coal reserves of the Basin together with the area&apos;s extensive history in electricity generation provide the rationale for establishing Ceramic Fuel Cells Ltd. A consortium comprising Australia&apos;s leading industrialist - BHP, State energy authorities and the Nation&apos;s major research and development organisations, has formed Ceramic Fuel Cells to undertake and manage research, development and commercialisation of solid oxide (ceramic) fuel cells which convert fossil fuels directly to electricity with greater efficiency and less pollution than existing technologies. The oil and gas resources of the Basin together with the valuable experience of the operators in recovering these resources, have provided the impetus to investigate the feasibility of a Marine Engineering Research Centre. The commercially oriented research, education and training objectives of the Centre are well supported by the leading industrialists in related industries.

Jan 1, 1992

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if&apos; the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.&apos;-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012

Application of Discrete Element Method for Simulating Feeding Conditions and Size Reduction in Cone Crushers

Sep 13, 2010

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks (&quot;magnetite&quot; concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

By K. Woodward

"SynopsisSeismically active mines generally experience an increase in seismic hazard due to rock mass instability following blasting. Re-entry protocols commonly include measures to limit the spatial and temporal exposure of personnel to increased seismic hazard induced by blasting. The management of periods of increased seismic hazard requires the development of re-entry protocols for a unique mining environment. Identifying mining conditions that may result in significant seismicity following blasting relies on retrospective analysis, which is often focused on seismicity occurring within a certain period after blasting and within a certain radius of the blast in the broader context of site-specific experience.The analysis of seismicity without considering blasting times and locations allows for the relationship between seismicity and blasting to be investigated without prior assumptions concerning dependency. To achieve independent analysis, seismicity that is clustered in space and time (referred to as a seismic sequence) must be identified by assessment utilizing only seismic parameters. An automated algorithm is implemented that assesses the timing, location, and quantity of seismicity to identify seismic sequences, represented by the time of the first event and mean location of all events in the sequence.The relationship between sequences and blasts is assessed by calculating the distance and time from each sequence to the closest blast in space and time. Establishing an independent classification between sequences and blasting provides insight into the unique cases where seismic sequences are remote and/or delayed with respect to blasts and identifies cases when sequences exhibit a weak relation to blasting. The nature of seismic responses to blasting has direct implications for the management of the increased seismic hazard associated with seismic sequences.The approach presented in this study contributes to the management of seismic hazard by providing empirical support for the relationship between seismic sequences and blasting. These relationships indicate the portions of sequences that can and cannot be practically managed using tactical approaches. Furthermore, the analysis of sequences reveals the nature and evolution of rock mass responses to blasting. These results have implications for the extent of spatial or temporal re-entry restrictions required for the optimal management of time-dependent rock mass response to mining."

Jan 1, 2015

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By Simon St. John Tose

We have had a long history in supporting the development of training material to ensure “safe” blasting. This has been provided as both significant technical guidance to the industry and input into the development of the new industry surface rockbreakers or shotfirers qualification in South Africa (RSA). The learning material supplied to the industry is based on both a classroom knowledge component and an assessment on the practical application of the learning by the trainee blaster on the job under the supervision of the appointed blaster. This training includes all blasting applications which can often extend beyond the “normal” mining environment of open pits, underground and quarries into civil applications such as trenches, blasting close to private buildings, public roads, pipelines, power lines, swimming pools and the removal of concrete structures and building demolitions etc.

Jan 1, 2013

By A Jewbali, J Phillips, C Boyle

Normal practice in the mining industry is the creation of a single geological model. These models provide a single interpretation of the geological and mineralisation domains. These interpretations infer the exact behaviour of ore domain contacts at shorter scales when resource definition drilling is done on wider scales and are thus locally highly uncertain. The interpreted geological model provides a single number for the volume and tonnes of mineralised material enclosed by the mineralisation envelope. It is on this single number for volume and tonnage that capital intensive mine development decisions (mine design and scheduling, stockpile strategy, waste management, closure planning, dewatering strategy, product quality, etc) are based. Some of these decisions require knowledge of grade variability for small volumes of material such as quarterly production periods. It is generally recognised that this information cannot be derived from single kriged geological models, but can potentially be modelled by conditional simulation techniques. Uncertainty in the extent and continuity of the mineralised envelope and its effect on grade variability for shorter production periods is thus recognised as a major source of uncertainty in new mine development.CITATION:Jewbali, A, Boyle, C and Phillips, J, 2013. Quantifying domain uncertainty for an iron ore deposit, in Proceedings Iron Ore 2013 , pp 157-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013