Search Documents

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

Alluvial gold grades are typically highly erratic. It is very often difficult to establish with confidence the in situ grades of reserve blocks due to the small number of pit or drill hole samples available, and their erratic values. Trends in grade are often obscure. Geostatical methods are inappropriate due to the extreme nugget effect found in alluvial gold field data. Classical statistics appear more suited to such data but require assumptions to be made regarding the nature of the population sampled. Recent developments in computer intensive non-parametric statistical methods provide a new approach to dealing with some of the above problems. These methods avoid making assumptions about the type of population distribution, usually through some kind of re-sampling scheme. The bootstrap procedure involves taking the estimate of interest and synthesising its population of by re-sampling the original data a large number of times (1000+), at random and with replacement. The synthetic population is then used to draw conclusions about the likely behaviour of the true population.

Jan 1, 1985

The use of black and white and colour infrared film in remote sensing of natural resources is reviewed. In heavlly-forested areas such as New Zealand, the main value of the method is in surveying the vegetation cover to detect the existence of plant communities characteristic of specific geological formations. By contrast in arid areas of Australia where the vegetation cover is sparse and where rocks and soils are well exposed, the method can be used in detecting different rock types or other geological differences.

Jan 1, 1972

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

Geological hazards such as faulting, basement ridges, and zones of "thin" (< 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

Eco-Efficient Gravity Separation Solutions in India Sustainable development and social responsibility issues are a principal aspect of mineral processing operations around the world. With the need for more environmentally effective technologies, some gravity separation systems have provided eco-efficient mineral processing solutions in places where it is not otherwise viable because of lack of fresh water or for other environmental reasons. Advanced spiral separation technologies developed in Australia offer a cost effective and environmentally viable way to process minerals. In particular, we review recent case studies of spiral plants commissioned in India where environmentally sustainable solutions to design problems included the use of spirals operated with sea water and the use of high capacity (HC) spirals to provide low consumption of energy and materials and a reduced plant footprint. This paper evaluates the performance of various spiral plants in India and how critical environmental issues which affect the overall viability of wet concentrating processes where resolved.

Sep 13, 2010

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By C. O. Aksoy, H. Kose, K. Heasley, E. Yalçin

"In Turkey, the growing demand for lignite has resulted in increased lignite production and an emphasis on improving underground recovery. This has resulted in a gradual increase in the application of the retreat longwall mining method and also in the extraction of the safety pillars protecting permanent underground structures (drifts, shafts) in mines prior to their abandonment.Extracting these safety pillars presents a special hazard to mine employees and the stability of the mine. Often subjected to high stresses, the behaviour of these pillars is not always predictable. Special care must be taken to ensure that infrastructure does not collapse prematurely, and that working conditions remain safe. Otherwise the extraction must be halted, and the remaining coal lost.This investigation reports on a study of the stability of safety pillars during the final extraction phase of the Hustas mine in Soma, Turkey.” The model construction was based on mine plans, and material properties were derived from physical properties testing. Observed subsidence effects from other mining events were used to calibrate the overburden lamination thickness.The model results compared well with surface physical disturbance occurring as a result of mining, as well as with conventional longwall stress redistribution theory and underground observations. The study has shown that properly calibrated models can be useful in assessing mine safety during remnant pillar extraction. The LAMODEL results demonstrate the convenience of this easy to use software."

Jan 1, 2004

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office operations. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggedized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys are accurate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine planning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of operations, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, productivity charts, and graphs. This information can be disseminated through various mine communication systems to provide operators and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in extensive trials are reporting productivity increases of 4 -7% or more thereby providing rapid payback to the mine.

Jan 1, 1998

By McLennan R. G

The principle of personal safety is as old as the human race. The application of this principle to industry is of much more recent origin, and may be said to be almost exclusively the product of the twentieth century. The enormous strides in technique and production mode prior to the turn of the century had been achieved without any real regard for the crippled human by-products of that expansive era. It was accepted that. accidents were inevitable and formed part of the price that must be paid for production. It was not until 1885 that the first Workmen's Compensation Act was passed in Germany making the employer financially liable for injuries suffered on his plant.With awakening social conscience came the first organised efforts to reduce accidents in industry. Early 19th century literature dealing with the development of powerdriven machinery and the growth of industry in Europe contains many references to the unsafe and unhealthy working conditions that accompanied the change-over from the home workshop to the industrial plant. By the year 1900, there were in Germany - and a little later in England governmental regulations dealing with the guarding of hazardous machinery. American industry, now the acknowledged leader in industrial safety, admits freely that when an organised safety movement commenced in that country, there was already a considerable amount of information available to them from European experience. The steel industry was well to the fore in this work, and in...

Jan 1, 1957

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By A. Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tons of which 22 million tons was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (north and south) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/h, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (define?measure?analyse ?improve?control), which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for ongoing fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of unblasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance with plan for actual hole depths was temporarily monitored by manual hole dipping, but this is now being replaced with a fully automated drill data management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods for the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire drill and blast process.

Jan 1, 2008