Search Documents

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973

By P Holtham, K Duffy, W Valery, A Jankovic

As high grade ore deposits are depleted, remaining deposits are generally lower grade and require the mining and processing of larger volumes of material per tonne of product. These low grade deposits often contain a large proportion of barren gangue. Pre-concentration aims to remove this barren material at as coarse a particle size and as early in the process as possible. This has the potential to reduce processing costs, energy and water consumption, increase production and improve resource utilisation.There are several technologies that may be applicable for pre-concentration. This paper looks specifically at bulk ore sorting and how it can be integrated into existing or new mining operations to improve profitability and reduce environmental impact. Bulk ore sorting is the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor measurement. It may be used to increase the production rate through fixed plant capacity, or increase production and/or reduce the size of downstream processing equipment in Greenfield operations. Marginal ore sub-economic reserves may be upgraded, making them economic to treat and improving the resource utilization. Bulk ore sorting could also be used to reduce dilution and ore loss in mining operations by improving grade control, or to separate ore types to treat via different process routes. Various applications of bulk ore sorting are discussed in this paper, and three cases are investigated considering the impact on the overall operation and the associated benefits.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Integrating bulk ore sorting into a mining operation to maximise profitability, in Proceedings MetPlant 2015, pp 273–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By David G. Borg

"Although researchers have realized varying degrees of success in numerics modeling, computer blast simulations and small scale in-situ testing, most will agree that the greatest uncertainty in total success stems from the uncontrollable field variables. Given the diverse nature of field conditiorencountered, no reliable and proven method of evaluating fragmentation quantitatively, and the lack of adequate field controls found in many operations, it is unlikely that a universal plug-in model will be developed for all blasting in the imediate future. This does not imply that all research devoted to modeling should cease, for it is precisely here where more research efforts are desperately needed."

Jan 1, 1989

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

By J Widjaja, E Hermawan, M Muharam, L Damanik

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The island of Java lies within the Sunda-Banda magmatic arc, which is characterised by multiple phases of volcanic activity and extensive compressional deformation. Along this zone, significant gold and copper mineralisation occurs, including some of the world’s largest deposits. In West Java, epithermal gold mineralisation is typically located in a series of extensional and strike-slip faults that cut Miocene to Pliocene volcanic rocks. These are all low-sulfidation, epithermal, vein-stockwork-style deposits developed in Miocene to Pliocene calc-alkaline volcanic rocks, which have been intruded by shallow-level plutons.This paper discusses an example of epithermal mineralisation at Mt Subang, West Java. Gold mineralisation was originally identified from stream sediment, panned concentrate and rock geochemistry sampling in the early 1990s. Geophysical surveys (magnetics and induced polarisation resistivity/chargeability), trenching, pitting and diamond hole drilling has subsequently revealed silicified-quartz vein epithermal gold mineralisation hosted within fault structures. It is clear that these structures acted as hydrothermal fluid pathways leading to the development of mineralised offshoots along north–south extensional and en-echelon arrays of north-east–south-west and transtensional faults. A number of vertical offshoots also occur in flexures and fault jogs. Post-mineral faulting has subsequently dissected and offset a number of the offshoots. Therefore, a detailed knowledge of structure and fault kinematics and displacement magnitudes is required in order to understand the geometry and continuity of mineralisation across major structures and maximise the resource potential. A range of exploration targets were modelled, indicating a minimum and maximum of 0.2 and 1.8 Moz of gold respectively.CITATION:Cunningham, M J M, Muharam, M, Damanik, L, Hermawan, E and Widjaja, J, 2015. Structural controls on the localisation of low-sulfidation epithermal mineralisation in West Java, Indonesia , in Proceedings PACRIM 2015 Congress, pp 227–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Lee Nichols

Convergent Bitumen Recovery Context of discussion It should be noted that the CBR process is a conceptual bitumen recovery feed methodology, designed to provide supplemental bitumen to the oil sand operations of Northern Alberta. To date the following have beencompleted. ?Bench Scale testing. ?Peer group brainstorming. ?Energy Balance ?Confidentiality agreements have been signed with several companies Discussions are ongoing with industry and although conceptual atthis stage the process holds significant promise.

May 1, 2007

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995