Search Documents

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By Syd Peng

"As the International Conference on Ground Control in Mining (ICGCM) enters its 35th year in 2015, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. In the past three decades, ground control has made a tremendous advancement, and many case studies published in the 36 volumes of proceedings have demonstrated its important role in the daily mining operations. However, there is still plenty of room for improvements. This paper discusses the research needs in 12 subject areas, including mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps.INTRODUCTIONThe International Conference on Ground Control in Mining (ICGCM) was founded in 1981. Since then, 1,546 papers have been published in the 36 conference proceedings, including the three surface subsidence workshops held in the 1981, 1986, and 1992. All types of topical areas regarding mining, from geotechnical core loggings in the exploration phase through backfilling after mining to finally spoil piles stability on the surface, have been addressed. A review of these papers, and other related literature as well, indicate that ground control has developed to become an inseparable part of mine design and a problem-solving tool for safe production.After 34 years, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. There is no doubt that the conference series has achieved the goal for which it was originally designed: to provide an annual forum for the exchange of information among the researchers, government regulators, equipment manufacturers, consultants, service providers, and—above all—mine operators. There have been many papers addressing the application of ground control techniques for successful mine design and safe production, and, without these papers, many projects would have failed. In fact, the conference emphasis on application types of papers may have steered too far toward the application side. A review of the conference papers shows that papers have been leaning mostly toward the applied side, leaving most, if not all, fundamental issues behind in nearly every topical area. This paper addresses research needs in 12 topical areas: mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps."

Jan 1, 2015

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By P. J. Coleman

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners? activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly under-stand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985.

Jan 1, 2010

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By Gabriel Alves Gomes

Neste trabalho, nanopartículas de ferrita mista cobre-prata foram estudas como uma opção viável de material bactericida reciclável. As nanopartículas Cu-Ag foram sintetizadas pelo método de combustão em solução e caracterizadas via difração de Raios-X. Ensaios in vitro foram estabelecidos como meio de avaliação do potencial de interação e da taxa média de inibição nas cepas S. Aureus e P. Aeruginosa, usando o método de difusão em meio ágar líquido. Análise por densidade óptica mostrou as comparações de quantidades relativas das cepas que foram eliminadas ou inibidas através dos mecanismos físicos das amostras. Resultados preliminares foram comparados com trabalhos semelhantes na literatura, indicando que a eficiência antibacteriana do material depende tanto do contato das partículas com a membrana celular das bactérias quanto do tamanho médio de cristalito das ferritas.

Oct 30, 2017

Aalde, Kaare. ('40) Gen'I Del., Bisbee. Ariz. Aase, Glenn D., ('40) Univ. of North Dakota. Grand Forks. N. D. Abadesco, Enrique A., ('39) College of Engrg.. Univ. of the Philippines. Manila, P. I. Abbott. John L., ('40) Colorado School of Mines. Golden. Colo. Abdul-Ahad, A., ('39) Montana School of Mines. Residence Hall, Butte. Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acomb, Allen. ('41) Louisiana State Univ., Box 1970, University. La. Acosta S., Gonzalo. ('40) Univ. of Texas, Univ. Sta., Box 1785. Austin, Tex. Adam, Howard W., ('41) Montana School of Mines. Butte, Mont. Adams, Albert, ('381 New Mexico School of Mines, Socorro. N. M. Adams. Charles W., ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams. H. Travis, ('39) 316 South -5th St., Bur¬bank. Calif. Adams, Jack L., ('39) Univ. of Oklahoma, Nor¬man. Okla. Adams. John W., ('41) Colorado School of Mines, Golden. Colo. Adams. Lewis J.. ('39) 402 Del Mar Blvd., Corpus Christi, Tex. Adams, Rob L., ('40) Agricultural & Mech. Col¬ lege of Texas. Box 600, College Sta., Tex. Adamson. Charles R., ('41) Univ. of Utah, Salt Lake City. Utah.

Jan 1, 1941

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By Jussi Vaamol

A commercial CFD-code was used to solve isothermal flow fields of gas and liquid in a Peirce-Smith converter. The model was validated with a 1/4 scale water model, and parametric study. Limits of the modeling technique used were recognized, but calculated results indicate that the present model predicts the general flow field with reasonable accuracy. The model was used to examine general flow conditions in an industrial scale PS-converter. Typical scaling factors of physical models were also evaluated with the aid of predicted bubble distribution, patterns of the flow fields and magnitude of flow velocities. The numerical simulations were found to open new viewpoints to the fluid dynamic related phenomena in the PS-process.

Jan 1, 1998

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire of the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By Edmund S. Leaver

The Precious Metals Section is concerned primarily with ore-testing problems associated with precious metals and with the analysis and concentration of a large number of the strategic-mineral samples that have been included in the research program of the Bureau of Mines. During the fiscal year 1938-39, 30 projects were completed. The requests for this service are based upon the desire f the sponsor to obtain the best or most satisfactory method for maximum recovery of the minerals. In many instances it is a question of improving present milling practice, with due regard to utilization of present equipment. In others, the probable tonnage available maybe the deciding factor in the choice of a particular recovery method. Under all circumstances the results of tests axe prepared with the thought of aiding a competent metallurgist, familiar with local conditions, to formulate a practical flow sheet or to assist the mill operator to correct known losses. A microscopic examination for identification of the mineral constituents and their association in each ore is always a big help, in planning the tests and may indicate the reason for former troubles or assist with best procedure.

Jan 1, 1940

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

Separating Particles by Horizontal Deflection in a Paramagnetic Fluid This paper describes the horizontal deflection behavior of particles in paramagnetic fluids under a high-gradient superconducting magnetic field. Movements of single particle were observed experimentally and indicated that they could be deflected to different positions. Based on these results, the behavior of groups of particles from ore samples was examined in the superconducting magnetic. It was found that these particles could be deflected and settled at a certain position due to the combination of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different susceptibilities and/or densities could be deflected to different positions, thus producing groupings of similar types of particles. The work described here, although in its infancy, could form the basis of new approach to separating particles based on a combination of susceptibility and density.  

Sep 13, 2010