Search Documents

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations' removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

Jan 1, 1920

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By Haitao Wang, Shen Wang, Dongyin Li, Yongjia Xu, Jinzhao Liu, Xiangjun Chen

The safe and efficient driving of the roadway along the gob is becoming an increasing challenge due to the influence of the integrity and bearing capacity of the side coal and rock mass in the gob under the roof cutting mining mode. The mechanism of protection of the gob-side roadway is shown by modeling the influence of roof cutting and the application of a destress technique on the lateral coal and rock mass zones. The distribution characteristics of stress, displacement, and fracture in the overburden are analyzed by numerical simulation method under the three working conditions. The results indicate (1) construction of row holes and blasting can form artificial structure’s fracture plane above the roadway, which can effectively cut the connection of overburden. The artificial structure’s fracture plane decreases the peak value of the lateral coal body’s support pressure. The peak point and the critical location of the stress reduction area are both transferred to the deep part at the same time, providing adequate space for the gob-side roadway. (2) The stress arch foot in the lateral rock mass rises to the rock layer at the bottom of the roof cutting plane after top cutting, as does the high-pressure area of deviator stress. The fracture plane prevents lateral coal and rock mass instability and limits the negative effects of roof deformation above the gob-side roadway. (3) The triangle slip fracture zone moves to over the roof cutting drilling zone due to the fracture plane, showing a high position compared to its original zone.

Jul 11, 2023

By D. W. Alexander

Researchers from the U.S. Office of Mine Safety and Health Research (OMSHR) of the U.S. National Institute for Occupational Safety and Health (NIOSH) completed field trials during coal mine rescue contests using simulated gas detectors in place of placards. The gas monitor simulator (GMS) devices replaced static, paper placards to deliver gas concentration data. Eleven teams were observed during the field contest, which was approved by the Mine Safety and Health Administration (MSHA). GMS devices were given to three team members (the captain and both gasmen). Observation of teams revealed that team members changed behavior by acknowledging and sharing information more often while using the GMS. As a result of this research, it has been demonstrated that under the existing contest format, the newly developed GMS device may be used with no adverse impact on team contest performance. Furthermore, when GMS technology advantages are used, contest realism is improved. In the future, competency assessment may be incorporated.

Jan 1, 2012

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By Arthur P. Nelson

In opening, I want to thank the program committee and members of the Society of Mining Engineers of AIME for the opportunity to speak to you. Various chapters of AIME this past year have expressed interest in the Federal Metal and Nonmetallic Mine Safety Act. We want to see that interest continue, because the reason for the legislation was the safety and health of the industry's workforce. The Department of the Interior was directed by the Congress to administer the provisions of the Act and is therefore held directly accountable for the success or failure of its intent. We intend to see it succeed. Among other things, the Act does provide for education and training under Section 15. This provision has been implemented and is expanding. However, the responsibility of my office is inspection and enforcement and that is my subject today.

Jan 1, 1973

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By Shounak Banerjee, Suresh Babu Dasari, Dharmendr Kumar, Shashank Pardhikar, Beena Rai, Venugopal Tammishetti

Recent increase in steel demand has led to the increased usage of high grade iron ores. During the mining, crushing and washing of ore, huge quantities of fines and slimes (<150 µm) are generated, majority of which is dumped into tailing ponds owing to their high alumina contents (~10-15%). Due to rapid depletion of high grade iron ore, it is the need of the hour to utilize low grade iron ore fines and slimes. These fines and slimes contain high iron values assaying 45-60% Fe. Dumping these valuable resources in ponds locks enormous land space and causes environmental hazards. The constituent minerals present in Indian iron ores comprise of hematite, goethite, gibbsite, kaolinite and quartz. Our research is focused on beneficiation of iron ore slimes through selective flocculation. We use density functional theory simulations to screen the reagents and perform experiments with screened reagents to determine the experimental conditions for effective performance of the reagents. Our studies revealed that reagents like starch, guar gum and carboxymethyl cellulose exhibit excellent selectivity in high alkaline pH range. However, the higher cost of alkali makes the process economically less attractive. In the present study, a commercial reagent from NALCO Water (Hi-Tex 83570) has been explored as selective flocculant for beneficiation of iron ore slimes in wide pH range (4-11). However, the reagent was also found to be the most selective in alkaline pH range only. Full factorial design of experiments was done considering three parameters namely, pulp density, flocculant dosage and settling time. Regression models were developed for yield, iron grade, alumina grade and iron recovery in the concentrate, using experimental results. Further parameter optimization was done to achieve high Fe recoveries and low alumina recoveries. The optimal parameters thus arrived at were validated with the experiments. We were able to achieve a concentrate grade of 60.0% Fe and 5.1% Al2O3 with 68.8% Fe recovery from a feed containing of 53.1% Fe and 8.9% Al2O3. The performance of flocculant Hi-Tex 83570 was also compared with reagents starch and guar gum.

Jan 1, 2018

By André Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Mines Camchib Inc.. It is characterized by very fine first generation gold and very coarse second generation electrurn. Successful milling required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented. As a result of the circuit modifications, gold recovery increased from 65 to 81% in flotation and cyanidation. Overall gold recovery increased from 77% to 88-89%. These improvements are mostly attibutable to the recovery of -10 urn gold, whose presence in the Joe Mann ore and original circuit tails had been identified by process mineralogy.

Jan 1, 1989

Variety among deserts is nearly as great as among other climatic environments. Common to most deserts, and to areas downwind from them, is the dominance of aeolian transport of surface material, at least during some seasons of the year. The result is dilution of local surface materials with varying proportions of chemically uniform fine sand and silt, often imported by the wind from remote areas. Fortunately, desert pavement,.even though separated from bedrock by a meter or more of nearly pure loess, is simply a diluted reflection of nearby bedrock. Infiltration of loess through the surface debris and the rudimentary soil-forming processes in the desert usually preserve the integrity of the pavement. This pavement, or its "downstream" derivatives, provides a suitable sample for exploration geochemistry if proper care is taken to circumvent the aeolian dilution. The simplest and most commonly used method of circumventing the dilution is to use a coarse fraction of soils or stream sediments, discarding or retaining the finer fraction depending upon the magnitude of the dilution. Where the coarse surface debris is composed of rock chips representative of the bedrock sources, the method is successful. Under most circumstances the coarse fraction of the surface material will give a fair representation of gross lithology and will occasionally give an indication of mineral- ization. The major drawback to this approach is that selective weathering and erosion in the vicinity of mineral deposits often lead to the loss of ore minerals into the finer fraction, leaving a coarse residue enriched in feldspar and particularly in quartz; thus, the geochemical signature from a mineral deposit is effectively reduced or completely masked. The second most commonly used method to overcome aeolian dilution, and probably the most effective at present, is to use a heavy- mineral concentrate. This approach presupposes that the chemical signature sought resides in a heavy mineral. Fortunately, the arid weathering cycle is conducive to the formation of a wide variety of secondary ore

Jan 1, 1988

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By Peter Allen, John R. Stuermer

COUNTRY RISK ANALYSIS A company operating in a foreign country assumes all the risks that it would at home. However, beyond these, it assumes risks that arise from the unique political economic, financial conditions of the foreign country which it operates. These risks are known as "country risks". The importance of these risks has grown appreciably in the recent past (particularly in the aftermath of Iran&apos;s revolution in the late 1970s and Mexico&apos;s debt rescheduling of 1982-83), and as a result, country risk analysis has become an increasingly useful management tool. Country risk analysis seeks to assess the probability that countries will service their aggregate foreign liabilities on time, as well as the probability that country conditions could inhibit the debt service capability of private sector debtors. This involves assessment of both the ability and the willingness of countries to meet their external liabilities in a timely fashion. "Ability" is linked economic and financial variables: principally, a country&apos;s economic structure, foreign exchange generating capacity and debt service burden. On the other hand, "willingness" is tied to political factors: mainly the economic/financial orientation of government policy and the stability of economic decision making. Ability: Economic, Financial Conditions and Prospects Judgement of a country&apos;s ability to meet foreign financial obligations begins with a detailed study of a country&apos;s external balance sheet which compares the country&apos;s foreign liabilities and assets. Table 1 below presents country balance sheets for Mexico, Korea and Indonesia. [TABLE 1 The External Balance 3-,-et 1983 (billions of dollars; Indonesia Mexico Korea Foreign Liabilities 31.1 67.6 40.5 By Source: Bank 13.1 75.5 26.3 Non-bank 18.0 12.114.2 Foreign Reserves 9.3 4.7 7.0] The large magnitude of Mexico&apos;s external debt (nearly $90 billion), compared to foreign assets of approximately $5 billion, illustrates the weakness of this country&apos;s external payments position, and the main reason that it has been unable to meet interest and principal payments and been forced to reschedule its foreign debt. On the other hand, the relationship between Korea&apos;s external liabilities and assets ($50.5 billion and $7 billion, respectively), is more favorable and helps explain why Korea has been able to meet debt service payments and maintain its access to the international capital markets. Indonesia has even a more favorable relationship between its foreign assets and liabilities, $31 billion and $9 billion, respectively, and its debt is mostly lower interest rate, non-bank debt, making for a less onerous debt service burden. After the balance sheet, the analysis turns to a comparison of the country&apos;s foreign exchange earning capacity and its prospective financing requirements, that is, the country&apos;s future earnings stream

Jan 1, 1985

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By Anderson Azevedo Agra

O Pó de Aciaria Elétrica (PAE) é um resíduo sólido gerado durante a fabricação de aços em usinas com Forno Elétrico a Arco (FEA). Esse resíduo contem quantidades apreciáveis de metais, tais como ferro e zinco, tornando sua reciclagem interessante não só do ponto de vista ambiental como econômico. Assim, esse trabalho teve como objetivo avaliar a autorredução de misturas de pó de aciaria elétrica e coque verde de petróleo (CVP). Para isso, misturas e pelotas de PAE:CVP, com variados teores de redutor, foram submetidas a ensaios de autorredução em termobalança e, na forma de pelotas autorredutoras, numa retorta aquecida em forno elétrico vertical. A redução das amostras foi analisada a partir da perda de massa das misturas. Além disso, a redução das pelotas autorredutoras foi observada através de análises de difração de raios X. Nestas análises foi possível verificar decomposição da Franklinita e a redução dos óxidos de Ferro e Zinco.

Aug 17, 2017

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There &apos;."&apos;as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924